Accelerated weathering properties of compatibilized composites made from recycled HDPE and nonmetallic printed circuit board waste

The main aim of this work is to examine the influence of the contents of nonmetallic printed circuit board (PCB) waste component on the photodegradation of recycled high‐density polyethylene (rHDPE) composites. The properties tested were chemical changes, flexural properties, color stability, water absorption, leaching properties, and crystallinity changes of the composites after exposure to 2,000 h of accelerated weathering. Surface degradation for composites with nonmetallic PCB was less compared to unfilled rHDPE mainly because glass fibers covered almost the whole surface of specimens, acting as a protective layer, thus, slowing down the photodegradation reaction. Incorporation of compatibilizer in rHDPE/PCB composites had played an important role in resisting degradation due to UV exposure. All the composite samples became lighter in the early stages of weathering exposure; however, compatibilized composites showed less lightening and reduction on strength and modulus. Carbonyl index increases with exposure time indicating that the oxidation reaction continuously occurred during the aging process. Incorporation of compatibilizer had successfully reduced the water absorption uptake by the composites and effectively delayed some degradation properties of weathering. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43110.     

Gallium gradients in Cu(In,Ga)Se2 thin‐film solar cells

The gallium gradient in Cu(In,Ga)Se₂ (CIGS) layers, which forms during the two industrially relevant deposition routes, the sequential and co‐evaporation processes, plays a key role in the device performance of CIGS thin‐film modules. In this contribution, we present a comprehensive study on the formation, nature, and consequences of gallium gradients in CIGS solar cells. The formation of gallium gradients is analyzed in real time during a rapid selenization process by in situ X‐ray measurements. In addition, the gallium grading of a CIGS layer grown with an in‐line co‐evaporation process is analyzed by means of depth profiling with mass spectrometry. This gallium gradient of a real solar cell served as input data for device simulations. Depth‐dependent occurrence of lateral inhomogeneities on the µm scale in CIGS deposited by the co‐evaporation process was investigated by highly spatially resolved luminescence measurements on etched CIGS samples, which revealed a dependence of the optical bandgap, the quasi‐Fermi level splitting, transition levels, and the vertical gallium gradient. Transmission electron microscopy analyses of CIGS cross‐sections point to a difference in gallium content in the near surface region of neighboring grains. Migration barriers for a copper‐vacancy‐mediated indium and gallium diffusion in CuInSe₂ and CuGaSe₂ were calculated using density functional theory. The migration barrier for the In_Cu antisite in CuGaSe₂ is significantly lower compared with the Ga_Cu antisite in CuInSe₂, which is in accordance with the experimentally observed Ga gradients in CIGS layers grown by co‐evaporation and selenization processes. Copyright © 2014 John Wiley & Sons, Ltd.     

A Nanochannel Platform for Single DNA Studies: From Crowding,Protein DNA Interaction,to Sequencing of Genomic Information

The study of nanochannel-confined DNA is important from biotechnological and biophysical points of view. We produce nanochannels in elastomer with soft lithography and proton beam writing. Issues concerning DNA confined in such quasi one-dimensional channels are discussed. We describe DNA stretching via the control of channel diameter and buffer conditions and how the extension can be interpreted with theory and computer simulation. We then discuss the conformation of nano-confined DNA crowded by neutral polymers and like-charged proteins. As an example of a protein that has an affinity to DNA, the effect of heat-stable nucleoid-structuring protein, H-NS, on the folding and compaction of DNA is reviewed. Compaction of DNA by eukaryotic protamine and unpacking of pre-compacted DNA through an increase in salt concentration are discussed. We review results obtained with a novel, cross-channel device that allows the monitoring of the dynamic, conformational response of DNA after exposure to a ligand or protein and/or a change in buffer conditions in situ. As a biotechnological application, linearization of DNA by bottlebrush coating with a polypeptide copolymer is discussed. It is demonstrated that large-scale genomic organization can be sequenced using single DNA molecules on an array of elastomeric nanochannels. Overall, our results show that the effects of ligands and proteins on the conformation, folding, and condensation of DNA are not only related to classical controlling factors, such as osmotic pressure, charge, and binding, but that the interplay with confinement in a nanospace is of paramount importance.     

Nanopaper membranes from chitin–protein composite nanofibers—structure and mechanical properties

Chitin nanofibers may be of interest as a component for nanocomposites. Composite nanofibers are therefore isolated from crab shells in order to characterize structure and analyze property potential. The mechanical properties of the porous nanopaper structures are much superior to regenerated chitin membranes. The nanofiber filtration‐processing route is much more environmentally friendly than for regenerated chitin. Minerals and extractives are removed using HCl and ethanol, respectively, followed by mild NaOH treatment and mechanical homogenization to maintain chitin–protein structure in the nanofibers produced. Atomic force microscope (AFM) and scanning transmission electron microscope (STEM) reveal the structure of chitin–protein composite nanofibers. The presence of protein is confirmed by colorimetric method. Porous nanopaper membranes are prepared by simple filtration in such a way that different nanofiber volume fractions are obtained: 43%, 52%, 68%, and 78%. Moisture sorption isotherms, structural properties, and mechanical properties of membranes are measured and analyzed. The current material is environmentally friendly, the techniques employed for both individualization and membrane preparation are simple and green, and the results are of interest for development of nanomaterials and biocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40121.     

Kinetic modeling of hemicellulose hydrolysis in the presence of homogeneous and heterogeneous catalysts

Kinetic models were developed for the hydrolysis of O‐acetyl‐galactoglucomannan (GGM), a hemicellulose appearing in coniferous trees. Homogeneous and heterogeneous acid catalysts hydrolyze GGM at about 90°C to the monomeric sugars galactose, glucose, and mannose. In the presence of homogeneous catalysts, such as HCl, H₂SO₄, oxalic acid, and trifluoroacetic acid, the hydrolysis process shows a regular kinetic behavior, while a prominent autocatalytic effect was observed in the presence of heterogeneous cation‐exchange catalysts, Amberlyst 15 and Smopex 101. The kinetic models proposed were based on the reactivities of the nonhydrolyzed sugar units and the increase of the rate constant (for heterogeneous catalysts) as the reaction progresses and the degree of polymerization decreases. General kinetic models were derived and special cases of them were considered in detail, by deriving analytical solutions for product distributions. The kinetic parameters, describing the autocatalytic effect were determined by nonlinear regression analysis. The kinetic model described very well the overall kinetics, as well as the product distribution in the hydrolysis of water soluble GGM by homogeneous and heterogeneous catalysts. The modelling principles developed in the work can be in principle applied to hydrolysis of similar hemicelluloses as well as starch and cellulose. © 2014 American Institute of Chemical Engineers AIChE J, 60: 1066–1077, 2014     

Influence of Ignition Sources on Heat Release Rate in the Furniture Calorimeter

When measuring the production rates of heat and smoke of upholstered furniture the ignition source must not influence the test results. In this paper variations in the strength, application time and geometry of the ignition burner used in the furniture calorimeter are studied. Results from replicate furniture calorimeter chair test show that the burning behaviour is almost independent of the burner intensity in the applied regime. Tests on six different furniture items were performed in the furniture calorimeter. The test objects were exposed to three intensity levels of ignition source. The sources were: a large propane burner giving 30 kW during 120 s and a smaller propane burner used at two levels of heat output, 1.7 and 5.8 kW during 90 s. The results showed that the burning behaviour of the furniture was very similar regardless of which burner was used. This was especially evident when the time regime between 50 and 400 kW was studied. The length of this period is a measurement on how quick untenable conditions are developing in a single, well-ventilated compartment.     

Role of Tyrosine Kinase Syk in Thrombus Stabilisation at High Shear

Understanding the pathways involved in the formation and stability of the core and shell regions of a platelet-rich arterial thrombus may result in new ways to treat arterial thrombosis. The distinguishing feature between these two regions is the absence of fibrin in the shell which indicates that in vitro flow-based assays over thrombogenic surfaces, in the absence of coagulation, can be used to resemble this region. In this study, we have investigated the contribution of Syk tyrosine kinase in the stability of platelet aggregates (or thrombi) formed on collagen or atherosclerotic plaque homogenate at arterial shear (1000 s⁻¹). We show that post-perfusion of the Syk inhibitor PRT-060318 over preformed thrombi on both surfaces enhances thrombus breakdown and platelet detachment. The resulting loss of thrombus stability led to a reduction in thrombus contractile score which could be detected as early as 3 min after perfusion of the Syk inhibitor. A similar loss of thrombus stability was observed with ticagrelor and indomethacin, inhibitors of platelet adenosine diphosphate (ADP) receptor and thromboxane A₂ (TxA₂), respectively, and in the presence of the Src inhibitor, dasatinib. In contrast, the Btk inhibitor, ibrutinib, causes only a minor decrease in thrombus contractile score. Weak thrombus breakdown is also seen with the blocking GPVI nanobody, Nb21, which indicates, at best, a minor contribution of collagen to the stability of the platelet aggregate. These results show that Syk regulates thrombus stability in the absence of fibrin in human platelets under flow and provide evidence that this involves pathways additional to activation of GPVI by collagen.     

Fluidization of spherical versus elongated particles: Experimental investigation using magnetic particle tracking

In biomass processing fluidized beds are used to process granular materials where particles typically possess elongated shapes. However, for simplicity, in computer simulations particles are often considered spherical, even though elongated particles experience more complex particle– particle interactions as well as different hydrodynamic forces. The exact effect of these more complex interactions in dense fluidized suspensions is still not well understood. In this study we use the magnetic particle tracking technique to compare the fluidization behavior of spherical particles to that of elongated particles. We found a considerable difference between fluidization behavior of spherical versus elongated particles in the time-averaged particle velocity field as well as in the time-averaged particle rotational velocity profile. Moreover, we studied the effect of fluid velocity and the particle's aspect ratio on the particle's preferred orientation in different parts of the bed, which provides new insight in the fluidization behavior of elongated particles.