Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

Application of the methylene blue test to cement raw materials

Characterisation of raw materials for Portland cement manufacture by use of the methylene blue adsorption method is discussed. The method is shown to be a simple, convenient ‘rule of thumb’ procedure. It provides a guide to the quantity and type of argillaceous minerals present in a given raw material sample.     

Wear in check valves due to flow induced motion

Experiments showing the frequency and amplitude of the flow induced motion of the gate for a 2- and a 4-in. swing check valve have been performed. The gate motion is due to turbulence in approach flow. We have found the dominant turbulent frequency of the approach flow is about half the natural frequency of the valves. The valves appear to be almost critically damped. Because of this, the valves respond almost as they would to a static force of the magnitude characteristic of the turbulent fluctuation in the flow. Both the dimensionless exciting force and the damping ratio have been found to be independent of valve size so the above statements are true for larger valves also. The recommended valve oscillation amplitudes and frequencies are used to calculate the wear at the shaft and at the stop. For an unpegged check valve, such as one of the 10-in. valves which was used at the San Onofre Nuclear Generation Station, it was found that shaft bearing wear would amount to 0.27 in.³/year and stop wear to 0.03 in.³/year.     

Why is software late? An empirical study of reasons for delay insoftware development

A study of the reasons for delay in software development is described. The aim of the study was to gain an insight into the reasons for differences between plans and reality in development activities in order to be able to take actions for improvement. A classification was used to determine the reasons. 160 activities, comprising over 15000 hours of work, have been analyzed. The results and interpretations of the results are presented. Insight into the predominant reasons for delay enabled actions for improvements to be taken in the department concerned. Because the distribution of reasons for delay varied widely from one department to another, it is recommended that every department should gain an insight into its reasons for delay in order to be able to take adequate actions for improvement     

Efficient QoS support in a slotted multihop WDM metro ring

A novel distributed access protocol for a slotted wavelength-division-multiplexing (WDM) metro ring employing all-optical packet switching and supporting quality-of-service (QoS) classes is presented and analyzed. Since we assume that there are more nodes than available wavelengths in the network, we obtain a scalable multihop WDM ring as underlying network architecture. By dividing each channel into several time slots and further applying destination release and slot reuse, data packets can be efficiently transmitted and received in a statistically multiplexed manner. In our architecture, each node is equipped with one tunable transmitter and one fixed-tuned receiver. Furthermore, as we generally consider so-called a posteriori access strategies, different packet selection schemes are proposed and compared. An analytical model based on the semi-Markov process methodology is developed to quantify the performance of one of these schemes. As a key element of the protocol, an efficient QoS support access mechanism is proposed and its performance is evaluated. The new QoS control scheme adopts a frame-based slot reservation strategy including connection setup and termination, which only slightly increases the signaling and node processing overhead. Thus, an efficient hybrid protocol combining connectionless and connection-oriented packet transmissions is proposed     

Intramolecular crosslinking of poly(vinyl alcohol)

Poly(vinyl alcohol) is crosslinked in dilute solution (c=0.1 wt%) with glutaraldehyde. The reaction product is characterized by viscometry and gel permeation chromatography (g.p.c.). The intrinsic viscosity decreases with increasing degree of crosslinking and does not depend on temperature. G.p.c. reveals that the reaction product is not homogeneous, but consists of a mixture of particles with different sizes, possibly both intra- and intermolecularly crosslinked molecules. The intramolecularly crosslinked molecules are smaller in size than the initial polymer molecules and their size depends on the degree of crosslinking. They possess a narrow particle size distribution even if the initial polymer sample had a broad molecular weight distribution.     

Immobilization and activation of vanadium(III) and titanium(III) single‐site catalysts for ethylene polymerization using MgCl2‐based supports

Significant increases in the activity of vanadium(III) amidinate catalysts for ethylene polymerization have been obtained by immobilization on a MgCl₂‐based support prepared by reaction of AlEt₃ with a MgCl₂/ethanol adduct. Catalyst immobilization and activation on this type of support prevents the rapid decay in activity observed under homogeneous polymerization conditions with unsupported catalysts. Stable polymerization activity is also observed with analogous titanium(III) complexes. Polyethylene with narrow molecular weight distribution and spherical particle morphology is obtained without reactor fouling. Copyright © 2005 Society of Chemical Industry