Particulate emissions from large-scale medium-speed diesel engines: 1. Particle size distribution

This paper addresses particulate matter (PM) size distributions in large-scale diesel engine exhaust. The test engines were multivariable large-scale turbo-charged, after-cooled medium speed (~ 500 rpm, ~ 1 MW power per cylinder) direct injection diesel engines. Emissions measurements were carried out while burning heavy fuel (HFO) and light fuel (LFO) oils. Test modes for investigation were propulsion mode (marine) and generator mode (power plant), with load varying from 25 to 100%. PM was measured using a gravimetric impactor with four impactor stages plus a filter, classifying particles between 0.005 and 2.5 μm (aerodynamic diameter). The results show that HFO firing produces significantly higher PM emissions (more than factor of ~three on mass bases for high load operation) compared to LFO, especially for particles smaller than 0.5 μm. This is mainly due to higher ash-forming elements and sulphur content of HFO. For HFO, the fraction of the finest particles increases with load, more strongly for generator mode than for propulsion mode, with generator mode giving ~ 50% higher PM emissions than propulsion mode. With LFO firing, the largest amount of fine PM was emitted at the lowest load, for propulsion mode being lower and almost independent of load at higher loads, while for generator mode a steady decrease in emissions with increasing load is seen for all PM size classes measured.     

Thermodynamic properties of malonic, succinic, and glutaric acids: evaporation rates and saturation vapor pressures

This work provides thermodynamic data, in particular, liquid-state saturation vapor pressures of three common slightly water soluble secondary organic aerosol components, namely, malonic, succinic, and glutaric acids. A modified tandem differential mobility analyzer system was used to measure evaporation rates of nanometer sized aqueous malonic, succinic, and glutaric acid droplets at relative humidities and temperatures relevant in the lower troposphere. Liquid phase saturation vapor pressures and other thermodynamic properties were derived from the measurements using a binary condensation model. The obtained expressions for liquid phase saturation vapor pressures compare well with extrapolated literature data. The importance of the choice of method for calculating activity coefficients is discussed.     

Infection of the Sunagoke moss panels with fungal pathogens hampers sustainable greening in urban environments

Drought and heat tolerance of the Sunagoke moss (Racomitrium japonicum) and the low thermal conductivity of the dry moss tissue offer novel greening and insulation possibilities of roofs and walls to mitigate the heat island phenomenon in urban environments. However, damage may appear in the moss panels under humid conditions in Japan. In this study we characterized fungi associated with the damaged areas of the Sunagoke moss panels. Fungi were identified by morphology and internal transcribed spacer (ITS) sequence analysis and tested for pathogenicity on R. japonicum (Grimmiaceae) and an unrelated moss species (Physcomitrella patens; Funariaceae) under controlled conditions. Alternaria alternata, Fusarium avenaceum and Fusarium oxysporum caused severe necrosis and death, whereas Cladosporium oxysporum and Epicoccum nigrum caused milder discoloration or chlorosis in both moss species. The fungi pathogenic on moss were closely related to fungal pathogens described from cultivated vascular plants. Ammonium increased severity of fungal diseases in moss. This study demonstrated that fungi can cause economically significant diseases in cultivated moss and hamper commercial use of the moss panels unless appropriate control methods are developed. Use of a single moss clone to cover large surfaces and the air pollutants such as ammonium may increase the risk for fungal disease problems.     

Softwood Distillate as a Bio-Based Additive in Wood-Plastic Composites

The possibility of using softwood distillate as a bio-based additive or filler in wood-plastic composites (WPCs) was studied by adding various amounts (1–20 wt%) of distillate to a commercial WPC consisting of thermally treated sawdust in a polypropylene (PP) matrix. Softwood distillate was obtained as a secondary product from industrial ThermoWood® processing and it was further processed in the laboratory. The addition of softwood distillate significantly enhanced the mechanical properties of WPC when the distillate content was 2 wt%; tensile strength increased by 5%, tensile modulus by 3%, flexural strength by 3%, and modulus of elasticity by almost 2% compared with the unmodified WPC. In addition, a considerable decrease (over 16%) in water absorption was observed on distillate addition. Proton-transfer-reaction time-of-flight mass-spectrometry (PTR-TOF-MS) analyses revealed that the addition of softwood distillate increased release rates of volatile organic compounds (VOCs) in general, and that the odor of acetaldehyde and guaiacol is detectable in several WPCs. Overall, softwood distillate had positive effects on this particular WPC.     

Temperature optimisation of a diesel engine using exhaust gas heat recovery and thermal energy storage (diesel engine with thermal energy storage)

Modern automotive diesel engines are so energy efficient that they are heating up slowly and tend to run rather cold at subzero temperatures. The problem is especially severe in mail delivery operations where the average speed is low and the drive cycle includes plenty of idling. The problem is typically solved by adding a diesel fuelled additional engine heater which is used for the preheating of the engine during cold start and additional heating of the engine if the coolant temperature falls below a thermostat set point during the drive cycle. However, this additional heater may drastically increase the total fuel consumption and exhaust gas emissions of the vehicle. In this study the additional heater was replaced by a combination of exhaust gas heat recovery system and latent heat accumulator for thermal energy storage. The system was evaluated on a laboratory dynamometer using a simulated drive cycle and in field testing in the city of Oulu (65°N), Finland in February 2009.     

Synchrotron radiation investigations of the Sr2MgSi2OT：Eu^2＋,R^3＋ persistent luminescence materials

The electronic and defect energy level structure of polycrystalline Sr₂MgSi₂O₇:Eu²⁺,R³⁺ persistent luminescence materials were studied with thermoluminescence and different synchrotron radiation spectroscopies (UV-VUV emission and excitation, X-ray absorption near-edge spectroscopy (XANES) and extended X-ray absorption fine structure (EXAFS)). Special attention was paid on the effect of the R³⁺ co-dopants on the persistent luminescence properties of the materials. Theoretical calculations using the density functional theory (DFT) were carried out simultaneously with the experimental work. The experimental band gap energy (E_g) value of ca. 7.1 eV agreed very well with the DFT value of 6.7 eV. The variation of the E_g value was attempted to relate with the trap structure as well as with the different properties of the R³⁺ co-dopants. The trap level energy distribution depended strongly on the R³⁺ co-dopant except for the shallowest trap energy above the room temperature remaining practically the same, however. The different processes in the mechanism of persistent luminescence from Sr₂MgSi₂O₇:Eu²⁺,R³⁺ were assembled and their contributions discussed.     

Water quality retrievals from combined Landsat TM data and ERS-2 SAR data in the Gulf of Finland

This paper presents the applicability of combined Landsat Thematic Mapper and European Remote Sensing 2 synthetic aperture radar (SAR) data to turbidity, Secchi disk depth, and suspended sediment concentration retrievals in the Gulf of Finland. The results show that the estimated accuracy of these water quality variables using a neural network is much higher than the accuracy using simple and multivariate regression approaches. The results also demonstrate that SAR is only a marginally helpful to improve the estimation of these three variables for the practical use in the study area. However, the method still needs to be refined in the area under study.     

Indoor Climate and the Performance of Ventilation in Finnish Residences

The purpose of the study was to gather information about the actual ventilation and indoor air quality and to evaluate the differences between houses and apartments with different ventilation systems. A sample of 242 dwellings in the Helsinki metropolitan area was studied over periods of no weeks during the 1988-1989 heating season. The mean air-exchange rates had a high variation (average 0.52 l/h, range 0.07-1.55 l/h). The ASHRAE minimum value of 0.35 l/h was not achieved in 28% of the dwellings. The air-exchange rates were significantly her in the houses than in the apartments (averages 0.45/0.64 l/h, p < 0.001); in the natural ventilation systems they, were slightly her than in the mechanical systems. The average temperature in the bedrooms was approximately 22 °C (range 18–27 °C), slightly but significantly higher in the apartment than in the houses. The average dust depositions were higher in the balanced ventilation systems than in the other systems. The median radon concentration was 82 Bq/m³ (range 5-866 Bq/m³); the Finnish target value of 200 Bq/m³ was exceeded in 17% of the houses but in none of the apartment. The measurements indicate that the indoor air quality in Finnish dwellings is not always satisfactory with reference to human health and comfort.