Cardiovascular effects produced by R-(+)-8-hydroxy-2-(di-n-propylamino) tetralin in the preoptic area of conscious rats

The effect of ancrod-induced defibrinogenation on thrombosis and bleeding time was determined in anesthetized rats. Functional plasma fibrinogen levels were reduced 42, 71, 94 and 93% by ancrod doses of 5, 10, 20 and 30 U/kg, respectively, while a 2.5 U/kg dose was without significant effect. Ancrod inhibited vena cava thrombosis induced by partial stasis of blood flow combined with mild vascular injury. Thrombus weight was decreased 85 and 93% by the 10 and 20 U/kg doses, but was unaffected at lower doses. In contrast, ancrod doses of up to 30 U/kg did not significantly decrease carotid artery thrombi formed in response to oxidative transmural vessel injury. Ancrod caused a dose-dependent increase in bleeding time measured by puncturing small mesenteric arteries with a hypodermic needle. The bleeding time increase was approximately 38% in response to the 2.5 and 5 U/kg doses, and 182% in response to the 10 U/kg dose. These studies demonstrate that ancrod-induced reductions in plasma fibrinogen more effectively inhibit venous compared to arterial thrombosis, although these activities require doses that also increase bleeding time in small arteries.     

Localization of G-proteins in macrophages and E. coli during phagocytosis

Heterotrimeric GTP-binding proteins (G-proteins) have been shown to play an important role in cellular signalling. However, G-protein involvement in the intracellular spreading of bacterial pathogens is still poorly understood. In this study, antibodies, that recognize G-protein alpha-subunits (anti-G alpha), were used to investigate the localization of G-proteins in the macrophage-like cell line P388D1 and E. coli, also in their L-forms, during phagocytosis. In E. coli, anti-G alpha-binding sites were detected preferably in the cell wall and septa of the whole bacterial forms as well as in the cytoplasm of L-forms. Western blotting of bacterial lysates demonstrated protein bands with positive immunoreaction to antibodies against Gs alpha, Gi alpha, and Gcommon alpha with a higher affinity to the antibody against Gs alpha. Immunoreaction with the anti-Gs alpha-antibody was markedly higher in pathogenic strains of E. coli. Because of the conserved structure in all GTP-binding proteins which seem to derive from a single primordial protein involved in signal transduction mechanisms, it is reasonable to assume that some anti-Ga-positive proteins in E. coli might be related to G-proteins of higher organisms. A putative candidate for bacterial G-proteins seems to be a 36 kDa protein. Enhancement in G-protein immunostaining in the cytoplasm of macrophages around the internalized bacteria testifies to the involvement of G-proteins in mediation of endocytosis responses of phagocytes.     

Hierarchical production control for a flow shop with dynamic setup changes and random machine breakdowns

In this paper, we study a manufacturing system consisting of two machines separated by two intermediate buffers, and capable of producing two different products. Each product requires a constant processing time on each of the machines. Each machine requires a constant non-negligible setup change time from one product to the other. The demand rate for each product is considered to be piecewise constant. Each machine undergoes failure and repair. The time-to-failure and time-to-repair are exponentially distributed random variables. The setup change and processing operations are resumable. We model our system as a continuous time, continuous flow process. An optimal control problem is formulated for the system to minimize the total expected discounted cost over an infinite horizon. To determine the optimal control policy structure, a discrete version of the problem is solved numerically using a dynamic programming formulation with a piecewise linear penalty function. A real-time control algorithm is then developed with the objective of maintaining low work-in-process inventory and keeping the production close to the demand. The algorithm uses a hierarchical control structure to generate the loading times for each product on each machine in real time and to respond to random disruptions in the system. The system is simulated using this algorithm to study its performance. The performance of the algorithm is also compared to alternative policies.     

Chemical characterization of in vivo aged zinc phosphate dental cements

The chemical composition of zinc phosphate dental cements aged in vivo was studied. Twenty-seven samples aged 2 to 43 years were investigated using X-ray diffraction, infrared spectroscopy, ³¹P nuclear magnetic resonance spectroscopy, thermogravimetric analysis and differential scanning calorimetry. Evidence for the presence of zinc oxide, amorphous zinc phosphate, water of hydration and crystalline zinc phosphate tetrahydrate was found. The latter was identified as hopeite; it was present in 92% of the cements studied. No correlation with time concerning either the chemical structure of the components or their relative amounts was found. Zinc phosphate dental cements show very good chemical stability on long-term use.     

Wind energy systems

Wind energy has matured to a level of development where it is ready to become a generally accepted utility generation technology. A brief discussion of this development is presented, and the operating and design principles are discussed. Alternative designs for wind turbines and the tradeoffs that must be considered are briefly compared. Development of a wind energy system and the impacts on the utility network including frequency stability, voltage stability, and power quality are discussed. The assessment of wind power station economics and the key economic factors that determine the economic viability of a wind power plant are presented     

Energy expenditure in workers who install plastic and metal pipes for water supplies and sewage

Since 1985, many drug abuse treatment centers and health care providers have implemented special education programs for individuals who inject drugs. They focus primarily on increasing awareness of the threat of the human immunodeficiency virus (HIV) being spread through drug injection equipment and by sexual activities. As part of the Drug Abuse Treatment for AIDS-Risk Reduction (DATAR) project, the AIDS/HIV Risk Reduction Module was designed to meet these special intervention needs. This study examined program impact on 110 methadone treatment clients. Results indicated that for those in treatment less than 4 months, the AIDS intervention program enhanced specialized knowledge about AIDS, aided in the reduction of AIDS-risky behaviors, and enhanced attitudes toward achieving and maintaining abstinence from drug use. Thus, AIDS education and intervention programs appear to be effective and should be emphasized in the early phase of drug abuse treatment.     

Effect of internal heating during hot compression on the stress-strain behavior of alloy 304L

The temperature change due to the conversion of mechanical deformation to internal heat and its effect on the as-measured stress-strain behavior of alloy 304L was investigated by means of initially isothermal (compression specimen, dies, and environment at same temperature at initiation of test), constant strain rate, uniaxial compression of laboratory-sized cylindrical specimens. Strain rate was varied in the range 0.01 to 1 s⁻¹, where the thermal state of the test specimen varied from nearly isothermal to nearly adiabatic, respectively. Specimens were deformed in the temperature range of 750 °C to 1150 °C to a strain of 1. The change in specimen temperature with applied strain was calculatedvia finite-element analysis (FEA) from the asmeasured stress-strain data. Selected predictions were confirmed with embedded thermocouples to verify the model employed. Temperature was found to increase monotonically with strain at a strain rate of 1 s^-1, consistent with what is theoretically expected for the adiabatic case. At the 0.1 and 0.01 s^-1 rates, the sample temperature initially increased, peaked, and then decreased as the sample thinned and the contact area between the sample and the cooler dies increased. As-measured stress was corrected for softening associated with deformational heating by interpolation between the various instantaneous stress-temperature behaviors. The resulting isothermal flow data are compared to those predicted by a conventional method that employs an empirical estimate of the heat retention efficiency of the test specimen, assumed dependent on strain rate but independent of strain, to reduce the increase in temperature calculated for the adiabatic case. Differences between the calculated isothermal stress-strain data from the two methods are discussed. Values for the apparent activation energy of deformation and the strain to the peak in the flow curve, which is associated with the onset of dynamic recrystallization, determined from isothermal stress-strain data differed significantly from those obtained from the as-measured compression test data. Formerly Senior Systems Engineer with EG&G Rocky Flats, Inc., is retired.     

Umbilical warts: a new entity?

Two cases of umbilical warts are described. The occurrence of these lesions was not previously known. In both cases there was a history of long-standing genital warts.