Quasi-static and dynamic crushing behaviors of aluminum and steel tubes with a cutout

Tubular members are commonly used as an energy absorber in engineering structures and many such members have a cutout. In this study, the crushing behaviors of tubes with a cutout are characterized and the effects of cutout on the energy absorption capabilities of these tubes are quantified. Systematic parametric studies were carried out to study the effect of material properties, including yield and ultimate strength of material, strain rate effect, location of cutout, tube length and impact speed on the crushing behaviors and energy absorption capacity of aluminum and steel tubes. First, a numerical model was constructed with a commercial explicit finite element code. It will be first proven that the numerical simulation can produce sufficiently accurate results in an economic manner. Subsequently, the crushing behavior of aluminum and steel tubes with a cutout was experimentally characterized and their energy absorption capacity was evaluated in terms of mean crushing force, peak crushing force and specific energy absorption (SEA). Tubes of various lengths with a cutout located at different locations, subject to both quasi-static and dynamic impact loadings were considered. For steel tubes, the numerical simulation investigated the influence of the strain rate effect and variation in strain hardening ratio of the material. Empirical equations describing the mean and peak crushing forces of aluminum and steel tubes with a cutout were developed using linear and nonlinear regression methods applied to the results obtained from the numerical and experimental studies.     

UV-LIGA深度光刻机平滑衍射技术研究

UV-LIGA深度光刻技术是加工微型机电系统的一项重要的微细加工技术。介绍了一种平滑衍射效应的位错强度叠加原理，它采用了蝇眼积分透镜去平滑衍射，并模拟数值计算了硅片表面的光强分布，最后给出了光刻结果。     

Bioactivity of antifouling paints based on organotin toxicants

This paper discusses the bioactivity of antifouling paints based on organotin toxicants, such as tributyltin fluoride (TBTF) and triphenyltin fluoride (TPTF). These compounds were used alone or mixed as the main toxicant in formulations. The use of TPTF or mixtures of TPTF and TBTF, with vinyl binders, led to paints with satisfactory bioactivity during a 24 months immersion period. With the same binders, TBTF alone provided only 12 months of antifouling protection. The correlation coefficients calculated from the fouling attachment values and the rosin content in the binder showed that the bioactivity of the tested formulations depended on the solubility of the toxicant in sea water and on the composition and solubility of the binders.     

Income, Time Effects and Direct Preferences in a Multimodal Choice Context: Application of Mixed RP/SP Models with Non-Linear Utilities

Transport problems typically involve at least two types of constraints, on income and on time. Therefore, the indirect utility function depends either on the income available after having subtracted the cost of the discrete alternative and on the free time left after having worked and travelled by each competing option. In the typical linear-in-the-attributes and in-the-parameters specification, that represents the first grade approximation of the indirect utility function, the effect of income and time constraints cancel out and only the cost and time of the alternatives matter in the comparison between them. From a microeconomic point of view this is equivalent to assume that income and time effects could be disregarded; which is not always the case. To account for these effects the utility function should include second order attributes; however, in non-linear utility functions it may not be easy to distinguish among several effects that could be relevant: direct preferences for good and leisure, and simple interactions between attributes other than income and time effects. This paper analyses these effects from a theoretical point of view focusing on the possible confounding problem in detecting income and time effects. We use a dataset collected for a modal choice context and containing both revealed and stated preference data, and estimate several NL models examining the effect of the different second-order terms on detecting income and time effects. We compared specifications including square cost and time attributes, interactions between time and cost, cost divided by the income available to be spent on free time, and time multiplied by free time. Our results confirm the strong effect of direct preferences for goods and leisure time on choice, and the potential confounding effect between quadratic attributes and other non-linear omitted terms. Finally, we also found that care should be taken in highlighting income and time effects using mixed data sources, since confounding effects can occur when non-linearities are accounted for in both data sets.     

On the behavior of microstructures with multiple length scales

The current study aims to provide fundamental insight into the behavior of microstructures containing grain sizes that span multiple length scales. A commercial 5083 Al alloy was selected as the material of interest to facilitate comparison with recently published data. The materials studied here were prepared via the thermal consolidation of powders that were cryomilled for different times (i.e., 0, 2, 4, and 8 hours). Following consolidation, the resultant microstructure was characterized by an equiaxed grain morphology with a size distribution centered around 200∼300 nm. Dispersed among the 200- to 300-nm grains were coarse-grained regions or ligaments with a grain size ranging from 600 nm to 2 μm. The occurrence of coarse-grained regions is rationalized on the basis of recrystallization or subgrain coarsening, whereas the occurrence of equiaxed fine regions is proposed to be a result of continuous grain growth. Two types of microstructures were selected for study, containing coarse-grained volumes of approximately 28 pct and 43 pct that corresponded to an ultimate tensile strength (UTS) of 566 MPa and 535 MPa, and a fracture strain of 3.2 pct and 3.5 pct, respectively. The observed ductility and the relevant toughening mechanisms were discussed in light of the presence of multiple length scales.     

Recovering spectral data from natural scenes with an RGB digital camera and colored filters

Many spectral‐recovery methods using RGB digital cameras assume the underlying smoothness of illuminant and reflectance spectra, and apply low‐dimensional linear models. The aim of the present work was to test whether a direct‐mapping method could be used instead of a linear‐models approach to recover spectral radiances and reflectances from natural scenes with an RGB digital camera and colored filters. In computer simulations, a conventional RGB digital camera with up to three colored filters was used to image scenes drawn from a hyperspectral image database. Three measures were used to evaluate recovery with the direct‐mapping method: goodness‐of‐fit, root‐mean‐square error, and a color‐difference metric. It was found that with two and three filters both spectral radiances and reflectances could be recovered sufficiently accurately for many practical applications. With little increase in computational complexity, an RGB camera and a few colored filters can provide significantly better recovery of natural scenes than an RGB camera alone. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 352–360, 2007     

Mechanical properties of iron processed by severe plastic deformation

In the present study, the mechanical properties of Fe processed via severe plastic deformation (equal-channel angular pressing (ECAP)) at room temperature were investigated for the first time. The grain size of annealed Fe, with an initial grain size of about 200 μm, was reduced drastically during ECAP. After eight passes, the grain size reaches 200 to 400 nm, as documented by means of transmission electron microscopy (TEM). The value of microhardness during pressing increases 3 times over that of the starting material after the first pass and increases slightly during subsequent pressing for higher-purity Fe. Examination of the value of microhardness after eight passes as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization, an observation that resembles the behavior reported for heavily deformed metals and alloys. The tensile and compression behaviors were examined. In tension, a drop in the engineering stress-engineering strain curve beyond maximum load was observed both in the annealed Fe and the ECAP Fe. This drop is related to the neck deformation. The fracture surface, examined by scanning electron microscopy (SEM), shows vein patterns, which is different from the dimples found on the fracture surface of annealed Fe. In compression, an initial strain-hardening region followed by a no-strain-hardening region was observed in the ECAP Fe. The yield strength in tension of the ECAP Fe was observed to be higher than that in compression. The strengthening mechanisms and softening behavior are discussed.     

Optical signal routing using emission packet positioning of semiconductor heterostructure

We present a novel optical switching technique utilizing emission packet positioning of semiconductor heterostructure. A modulation-doped p-AlGaAs-GaAs heterostructure is employed to control spontaneous emission packet positioning with electric fields. Emission packets generated by optical input signals are brought over 150 /spl mu/m with electric fields, so the output fibers can detect the emission intensity as signals. The first-order analysis indicates that the drift velocity of minority electrons in GaAs limits the detectable maximum data rate and nanoseconds timescale signal routing operation at 20 Gb/s is possible at an electron drift velocity of 2/spl times/10/sup 7/ cm/s.