A lumped-parameter transducer model for piezoelectric and ferroelectret polymers

We have developed a model to describe the sensor operation of piezoelectric and ferroelectret polymer materials. The lumped-parameter model for the sensors describes the interaction between a mechanical motion and an electrical signal. The differences in material properties are considered in the model, and especially, the effects of dynamic and static forces and temperature to the electrical output signals provided by the sensors constructed from the materials are discussed.     

System- and circuit-level optimization of PLL designs for DVB-T/H receivers

This article proposes a framework for the optimization of voltage-controlled oscillator (VCO) designs in frequency synthesizers for digital video broadcasting ?C terrestrial/handheld (DVB-T/H) receivers. Linear time-invariant phase-domain model of a charge-pump phase-locked loop (PLL) is devised and includes both flicker (1/f) and thermal noise contributions from the loop oscillators. By modeling the entire receiver, it is shown that there are combinations of flicker and thermal noise contributions that result in a constant sum of inter-carrier interference (ICI) and adjacent channel interference, and constant symbol error rate as well. Consequently, optimization of the VCO phase noise spectrum is defined while maintaining the standard-specified symbol-error rate. Link-level performance evaluation is carried out to validate the stipulated trade-off. The effect of ICI mitigation schemes is discussed. Circuit-level VCO design approaches utilizing the derived trade-off are finally presented. The proposed optimization procedure is generic and is also applicable to other systems based on Orthogonal Frequency-Division Multiplexing.     

Targeting Efficiency and Biodistribution of Zoledronate Conjugated Docetaxel Loaded Pegylated PBCA Nanoparticles for Bone Metastasis

In an attempt to improve tumor localization of docetaxel (DTX)‐loaded nanoparticles (NPs), zoledronic acid (ZOL) is used as a ligand to target bone metastasis. DTX‐loaded ZOL‐conjugated polyethylene glycol (PEG)ylated polybutyl cyanoacrylate (PBCA) NPs are prepared using an anionic polymerization technique. PBCA‐PEG‐ZOL NPs are subjected to cytotoxic assay in both BO2 and MCF‐7 cell lines. Cell cycle arrest and apoptosis induced by the PBCA‐PEG‐ZOL NPs are studied. Quantitative cellular uptake, NP uptake route characterization, confocal microscopy and IPP/ApppI levels are performed. PBCA‐PEG‐ZOL NPs show an enhanced cytotoxic effect in both BO2 as well as MCF‐7 cell lines due to higher uptake following ZOL‐mediated endocytosis. The molecular basis of apoptosis reveals the involvement of a cytoplasmic protein in activating the programmed cell death pathway. Route characterization studies reveal that PBCA‐PEG‐ZOL NPs uptake is not completely blocked even by using both inhibitors (genistein and phenyl arsinoxide) simultaneously, conferring that uptake is not entirely based upon clathrin or caveolae. PBCA‐PEG‐ZOL NPs showed 7 and 5.3 times increase in IPP and ApppI production, in comparison to ZOL treatment, and 138 times higher than the control group in MCF‐7 cell line. In BO2 cell line, after treatment with NPs, IPP was 5.35 times higher than ZOL solution. No ApppI in BO2 cell line after treatment with NPs and ZOL solution was found. NP distribution in tumor infected bone is also significantly high in comparison to the normal bone at any time point. It is concluded that ZOL‐conjugated NPs provide an efficient and targeted delivery of DTX, with synergistic effects. Thus, these NPs present a promising treatment in the near future, by actively targeting metastatic tumor.     

Identification of adequate neurally adjusted ventilatory assist (NAVA) during systematic increases in the NAVA level

Neurally adjusted ventilatory assist (NAVA) delivers airway pressure (P(aw)) in proportion to the electrical activity of the diaphragm (EAdi) using an adjustable proportionality constant (NAVA level, cm·H(2)O/μV). During systematic increases in the NAVA level, feedback-controlled down-regulation of the EAdi results in a characteristic two-phased response in P(aw) and tidal volume (Vt). The transition from the 1st to the 2nd response phase allows identification of adequate unloading of the respiratory muscles with NAVA (NAVA(AL)). We aimed to develop and validate a mathematical algorithm to identify NAVA(AL). P(aw), Vt, and EAdi were recorded while systematically increasing the NAVA level in 19 adult patients. In a multistep approach, inspiratory P(aw) peaks were first identified by dividing the EAdi into inspiratory portions using Gaussian mixture modeling. Two polynomials were then fitted onto the curves of both P(aw) peaks and Vt. The beginning of the P(aw) and Vt plateaus, and thus NAVA(AL), was identified at the minimum of squared polynomial derivative and polynomial fitting errors. A graphical user interface was developed in the Matlab computing environment. Median NAVA(AL) visually estimated by 18 independent physicians was 2.7 (range 0.4 to 5.8) cm·H(2)O/μV and identified by our model was 2.6 (range 0.6 to 5.0) cm·H(2)O/μV. NAVA(AL) identified by our model was below the range of visually estimated NAVA(AL) in two instances and was above in one instance. We conclude that our model identifies NAVA(AL) in most instances with acceptable accuracy for application in clinical routine and research.     

Thermoset lactic acid‐based resin as a matrix for flax fibers

Thermoset composites were produced from flax fibers and a novel lactic acid (LA)‐based thermoset resin. This resin is based on methacrylated, star‐shaped oligomers of LA. The main purpose of this work was to evaluate whether this resin can be used to produce structural composites from flax fibers. Composites were prepared by spray impregnation followed by compression molding at elevated temperature. The tests showed that composites can be produced with as much as 70 wt% fiber. The composites were evaluated by tensile testing, flexural testing, charpy impact test, dynamic mechanical thermal analysis (DMTA), and low‐vacuum scanning electron microscopy. The ageing properties in high humid conditions were evaluated, the Young's modulus ranged from 3 GPa to 9 GPa in the best case. This work shows that structural composites can be produced from renewable material. It is clear from the results that these composites have properties that make them suitable for furniture, panels, or automotive parts. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Photoluminescence of spray pyrolysis deposited ZnO nanorods

Photoluminescence of highly structured ZnO layers comprising well-shaped hexagonal rods is presented. The ZnO rods (length 500-1,000 nm, diameter 100-300 nm) were grown in air onto a preheated soda-lime glass (SGL) or ITO/SGL substrate by low-cost chemical spray pyrolysis method using zinc chloride precursor solutions and growth temperatures in the range of 450-550°C. We report the effect of the variation in deposition parameters (substrate type, growth temperature, spray rate, solvent type) on the photoluminescence properties of the spray-deposited ZnO nanorods. A dominant near band edge (NBE) emission is observed at 300 K and at 10 K. High-resolution photoluminescence measurements at 10 K reveal fine structure of the NBE band with the dominant peaks related to the bound exciton transitions. It is found that all studied technological parameters affect the excitonic photoluminescence in ZnO nanorods.PACS: 78.55.Et, 81.15.Rs, 61.46.Km.     

Synthesis of poly(ester‐anhydride)s based on poly(ϵ‐caprolactone) prepolymer

The objective of this study was to prepare high molecular weight poly(ester‐anhydride)s by melt polycondensation. The polymerization procedure consisted of the preparation of carboxylic acid terminated poly(?‐caprolactone) prepolymers that were melt polymerized to poly(?‐caprolactone)s containing anhydride functions along the polymer backbone. Poly(?‐caprolactone) prepolymers were prepared using either 1,4‐butanediol or 4‐(hydroxymethyl)benzoic acid as initiators, yielding hydroxyl‐terminated intermediates that were then converted to carboxylic acid‐terminated prepolymers by reaction with succinic anhydride. Prepolymers were then allowed to react with an excess of acetic anhydride, followed by subsequent polycondensation to resulting high molecular weight poly(ester‐anhydride)s. Upon coupling of prepolymers, size exclusion chromatography analyses showed an increase from 3600 to 70,000 g/mol in number‐average molecular weight (M_n) for the 1,4‐butanediol initiated polymer, and an increase from 7200 to 68,000 g/mol for the 4‐(hydroxymethyl)benzoic acid‐initiated polymer. 4‐Hydroxybenzoic acid and adipic acid were also used as initiators in the preparation of poly(?‐caprolactone) prepolymers. However, with these initiators, the results were not satisfactory. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 176–185, 2001     

Transition metal phthalocyanine-modified shungite-based cathode catalysts for alkaline membrane fuel cell

The alkaline anion exchange membrane fuel cell (AEMFC) is one of the green solutions for the growing need for energy conversion technologies. For the first time, we propose a natural shungite based non-precious metal catalyst (NPMC) as an alternative cathode catalyst to Pt-based materials for AEMFCs application. The Co and Fe phthalocyanine (Pc)-modified shungite materials were prepared via pyrolysis and used for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) studies. The most promising ORR performance was observed in alkaline media for FePc-modified and acid-leached shungite-based NPMC material. The catalysts were also evaluated as cathode materials in a single cell AEMFC and peak power densities of 232 and 234 mW cm^?2 at 60 °C using H₂ and O₂ gases at 100% RH were observed for CoPc- and FePc-modified acid-treated materials, respectively.     

Effect of Shot Peening Parameters to Residual Stress Profiles and Barkhausen Noise

The production of gear components includes numerous manufacturing operations which are carried out to ensure proper surface characteristics of components to deal with wear and fatigue. Surface shot peening is one way to increase the compressive residual stresses on the surface and thus ensure better wear and fatigue resistance. An experimental plan for shot peening was conducted to produce samples with varying surface characteristics. Residual stress profile and Barkhausen noise measurements were carried out for the samples. The objective of the study was to evaluate the interactions between the shot peening parameters studied, the residual stress profiles and the Barkhausen noise measurements. A multivariable regression analysis was applied for the task. Some remarkable correlations were found between the shot peening parameters, residual stress profile and Barkhausen noise features. The most important finding was that when the shot peening intensity was high enough, over 0.5 mmA, it dominated the shot peening coverage density parameter and thus no correlations could be gained. On the other hand, if the intensity parameter was lower than the limit of 0.5 mmA, the correlation between residual stress and Barkhausen noise measurements was remarkable. This means that the surface Barkhausen noise measurements could be used for the evaluation of the stress gradient in the shot peening process.