Bio-Wax Latex-Modified Paper as Antimicrobial and Water-Vapor-Resistant Packaging Material

Beeswax and carnauba wax latex particles grafted with antimicrobial agents polyhexamethylene guanidine hydrochloride and polyhexanide were prepared by coupling reaction using N-(3-dimethylaminopropyl)-N’-ethylcarbodiimide hydrochloride as a coupling reagent. As a bifunctional agent for the surface treatment of paper the modified bio-wax latex improved the property of water-vapor resistance and antimicrobial activities of paper significantly after coating. Compared with the control sample the water vapor transmission rate (WVTR) of the paper with coating weight of 12 g/m² was reduced significantly from 2788.8 g/m²/d to 222.0 g/m²/d (BW-Gly-PHGH) thus demonstrating excellent water vapor barrier performance. The shaking flask method was utilized to investigate the antimicrobial activity against E. coli. The results showed that antimicrobial performance was improved substantially when the amount of added modified bio-wax particles was higher than 20 mg/g fiber. The bacterial inhibition ring test indicated that the antimicrobial mode of the modified bio-wax particles was likely based on the contact mode.     

浅谈煤粉锅炉干渣除渣系统设备选型

结合新疆南部某新建规模为2×130 t/h高温高压煤粉锅炉工程项目,为了选择合适的煤粉锅炉干渣除渣系统,比较了冷渣设备、输渣设备、渣库类型和装车卸料设备等,选择了风冷干渣机、斗式提升机输送、钢结构渣库和散装机装车卸料的干渣除渣方案,既节能环保,又技术可靠。     

铜铝异步轧制复合工艺及组织性能

采用异步轧制工艺进行了铜铝薄带的复合,并对复合带进行了退火处理,利用金相显微镜、扫描电镜和拉伸试验机进行了复合带组织的观察和性能的测定.结果表明,异步轧制相比同步轧制的界面波浪状形貌明显减少,界面更加平整;在相同的压下率下,异步轧制的轧制力要小于同步轧制的轧制力,使轧制的稳定性和精度得到了提高,有益于提高界面剥离强度;异步速比与复合带界面的剥离强度呈抛物线关系,异速比为1.25界面的剥离强度最大;异步速比增加,铜/铝复合带Cu/Al厚度比增加.所得结果在铜铝薄带轧制复合领域的研究有重要意义.     

Experimental studies on the effects of bearing supply gas pressure on the response of a permanent magnet disk-type motor rotor

Vibrations, particularly low-frequency vibrations caused by self-excited gas films, significantly affect the safety and economy of turbomachinery, which becomes dangerous at high rotational speeds. This experimental study focuses on the dynamic characteristics of a Permanent magnet (PM) disk-type motor rotor supported by gas aerostatic bearings. Nonlinear dynamic behavior, including double low frequency and gas film half whirling, was analyzed in the experiments. The dynamic features of double low frequency and gas whirling are described in the paper. The most important finding is that the sum of the whirling ratios of low frequencies 1 and 2 is always 1.00. The occurrence mechanism requires further study. The effects of bearing supply gas pressure on the dynamic response characteristics of the multi-disk PM rotor are implemented to improve rotor stability.     

Numerical simulation of cavitation surge and vortical flows in a diffuser with swirling flow

The strong swirling flow at the exit of the runner of a Francis turbine at part load causes flow instabilities and cavitation surges in the draft tube, deteriorating the performance of the hydraulic power system. The unsteady cavitating turbulent flow in the draft tube is simplified and modeled by a diffuser with swirling flow using the Scale-adaptive simulation method. Unsteady characteristics of the vortex rope structure and the underlying mechanisms for the interactions between the cavitation and the vortices are both revealed. The generation and evolution of the vortex rope structures are demonstrated with the help of the iso-surfaces of the vapor volume fraction and the Qcriterion. Analysis based on the vorticity transport equation suggests that the vortex dilatation term is much larger along the cavity interface in the diffuser inlet and modifies the vorticity field in regions with high density and pressure gradients. The present work is validated by comparing two types of cavitation surges observed experimentally in the literature with further interpretations based on simulations.     

Sn改性Ti-Zr-Cu-Ni钎料的微观组织和力学性能

采用自制Ti-Zr-Cu-Ni-Sn钎料钎焊TA2钛合金,研究了不同Sn元素含量改性Ti-Zr-Cu-Ni钎料的熔化特性、微观组织及物相、润湿及熔蚀性、接头拉伸强度。研究表明,Sn含量增加,Ti-Zr-Cu-Ni-Sn钎料固、液相线温度基本升高,但温度差值基本变窄,可更好地抑制钎焊界面脆性化合物形成。Ti-Zr-Cu-Ni-5Sn钎料组织由Ti、Zr基体和晶体相构成,Sn倾向与Ti、Zr结合形成Ti₂Sn₃、Ti₆Sn₅、Zr₅Sn₃等低熔点共晶相。Sn≤1.5%时,随Sn含量增加,钎料对TA2钛合金的润湿性逐渐变差;继续增加Sn,钎料润湿性改善,添加5%Sn的钎料对基体润湿最佳。添加5%Sn并降低Cu、Ni总量的改性钎料对TA2钛合金熔蚀减弱。相同钎焊工艺下,添加5%Sn接头的强度和塑性均有提升。钎焊温度升高,Ti-Zr-Cu-Ni钎料产生更多强化物相,致接头强度大幅提升,而Ti-Zr-Cu-Ni-5Sn钎料产生的含Sn物相强化作用对接头强度提升有限;相...     

SiC纳米线对Ni-Cr-P钎料及Ni-Cr-P/Q235焊点组织与性能影响

采用具有优良高温强度、高热导率、高耐磨性能和耐腐蚀性能的SiC纳米线为Ni-Cr-P钎料的添加物,研究了钎料/焊点的组织与性能。结果表明,钎料的组织由Ni(Cr)固溶体、Ni₃P固溶体以及Ni(Cr)和Ni₃P共晶组织组成,微量的SiC纳米线可以显著细化基体组织,使焊点抗剪切强度提高29.6%。SiC纳米线的添加使钎料的熔化温度提高约4℃,显著促进钎料在Q235基板表面的润湿性,增幅达到12.5%。然而,过量添加SiC纳米线会显著粗化基体组织,降低钎料的润湿性和焊点的抗剪切强度。在不同SiC含量的Ni-Cr-P钎料中,Ni-Cr-P-0.1SiC钎料/焊点具有明显的优越性。     

TiC/Ti层状复合材料组织与力学性能研究

为了平衡钛基复合材料（titanium matrix composites, TMCs）的强度和延展性,通过电泳沉积将氧化石墨烯（graphene oxides, GOs）沉积到Ti箔表面,然后进行放电等离子烧结（spark plasma sintering, SPS）制备了具有层状结构的原位TiC/Ti复合材料,并对复合材料进行冷轧和退火处理从而进一步优化复合材料的综合力学性能。结果表明,烧结过程中,Ti箔表面的GOs与Ti基体反应形成了原位TiC,从而形成了TiC/Ti层状复合材料,随着沉积时间的增加,分布在Ti层之间的TiC的含量增加;复合材料经过冷轧和退火后,退火态材料的晶粒为等轴晶,且TiC仍然保持层状分布特征。沉积时间120 s时,烧结态材料的抗拉强度（UTS）为555 MPa,伸长率（δ）为15%;退火态材料的抗拉强度为568 MPa,伸长率为27%,相比于烧结态材料,退火态材料达到了较好的强塑性匹配。此外,基于微观组织及断裂行为的分析对复合材料的强韧化机制进行了讨论。     

装配式拼装型减震墙板框架单元性能试验研究

为研究装配式拼装型减震墙板框架的减震机理与性能,设计4榀单层单跨装配式减震墙板框架、普通墙板框架和空框架模型试件,通过低周反复加载试验对比研究其破坏特征、滞回曲线、刚度退化和耗能能力等。试验结果表明：装配式拼装型减震墙板框架滞回曲线饱满、耗能能力强;拼装型减震墙板所提供的附加抗侧刚度和水平承载力有限,释放对装配式框架的过强约束作用,从而减轻或避免普通填充墙板附加刚度效应所带来的结构抗震不利影响;无论拼装与否,减震墙板通过合理构造与设计均可减小或避免大位移加载工况下墙板自身的破坏;拼装型减震墙板应注意墙板施工精度控制,否则会影响其减震性能,导致不必要的墙板破坏。