Agility through discipline: a debate

While Beck asserts that agility is only possible through greater discipline on the part of everyone involved, Boehm counters that you don't broaden the definition of "discipline" by rejecting parts of it. Yet, from inside extreme programming, it seems that the only way to achieve the desired results is to view the world in 'both-and" terms instead of "either-or" terms.     

Thermal storage efficiencies of two solar saltless water ponds

A comparative study between two types of solar ponds is presented. The first type has its free surface covered by a thin layer of transparent paraffin oil. The second type is covered by transparent glass floating devices. Each device disposes an air-vacuum chamber. The free water surface between these devices is covered by transparent paraffin oil also. The thermal storage efficiency of each pond is estimated during two time periods: between sunrise and sunset and from midnight to midnight. The calculated efficiency between sunrise and sunset corresponds to the average transmittance–absorptance product. This is estimated using linear regression and also a maximum likelihood identification technique. The behavior of the system was studied by solving numerically the heat transfer equations of the system. Also an ARMAX (AutoRegressivie Moving Average with eXogenous signal) model allowing the assessment of its performance was presented. This efficiency is larger for the first pond during the sunrise to sunset period and smaller when calculated from midnight to midnight. Thus, the first type of pond could be preferred for a use just after the sunset of the same day, while the second for use after one or more days of heat storage.     

One-dimensional diffuser based on a thick layer of dichromated gelatin

A new diffuser capable of scattering light in one direction (one-dimensional diffuser) has been developed and experimentally tested. The diffuser is formed in a thick layer of dichromated gelatin. The scattering indicatrices of the diffuser measured in two mutually perpendicular directions are presented. It is demonstrated that the indicatrix width in one direction is significantly greater than that in the perpendicular direc-tion. However, no zero-order diffraction has been observed. The proposed one-dimensional diffuser exhibits close scattering indicatrices for reading at a wavelength of 0.44 and 0.63 μm.     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.     

Electrospray droplet sources for thin film deposition

Electrospraying utilises electrical forces for liquid atomisation. Droplets obtained by this method are highly charged to a fraction of the Rayleigh limit. The advantage of electrospraying is that the droplets can be extremely small, down to the order of 10’s nanometres, and the charge and size of the droplets can be controlled to some extent be electrical means. Motion of the charged droplets can be controlled by electric field. The deposition efficiency of the charged spray on an object is usually higher than that for uncharged droplets. Electrospray is, or potentially can be applied to many processes in industry and in scientific instruments manufacturing. The paper reviews electrospray methods and devices, including liquid metal ion sources, used for thin film deposition. This technique is applied in modern material technologies, microelectronics, micromachining, and nanotechnology.     

Static and pulsed pressures measured using electrically conducting rubbers

A method of measuring static and pulsed pressures using electrically conducting rubber sensors is proposed. The method is based on a change in the volume resistivity of a filled rubber under the action of external pressure. The pressure-induced change in resistance of the rubber sensor is proportional to the applied pressure and can be measured by a bridge circuit. Using this method, it is possible to evaluate the degree of homogeneity of the pressure distribution over a solid surface. This is achieved by distributing rubber sensors over the given surface.     

Copper-zirconium tungstate composites exhibiting low and negative thermal expansion influenced by reinforcement phase transformations

A fully-dense Cu-75 vol pct ZrW₂O₈ metal matrix composite was fabricated by hot isostatic pressing of Cu-coated ZrW₂O₈ particles. A small amount of the high-pressure γ-ZrW₂O₈ phase was created during the cooldown and depressurization following densification; near complete transformation to γ-ZrW₂O₈ was achieved by subsequent cold isostatic pressing. The thermal expansion behavior of the composite between 25°C and 325°C was altered by the cold isostatic pressing treatment, and also depended on the length of time that had passed between thermal cycles. The measured thermal expansion coefficients within specific temperature ranges varied from −6·10⁻⁶ K⁻¹ to far above the thermal expansion coefficient of the copper matrix. The complex temperature-dependent expansion/contraction behavior could be justified by considering the evolution of phase transformations taking place in the ZrW₂O₈ phase, which were observed by in-situ synchrotron X-ray diffraction measurements.     

Study of phase equilibria in the Al - Pd - Re system

Scanning and transmission electron microscopy have been combined with x-ray diffraction to examine the phase equilibria in the Al - Pd - Re system at 1000°C for compositions from 50 to 100 at.% Al, and the corresponding isothermal section has been constructed. The binary monoclinic Al₃ Re phase has been observed for the first time. It is confirmed that there is a stable icosahedral phase in this system. The boundaries to its homogeneity region have been determined and the phase equilibria in which it participates.     

The Computational Chemistry Prototyping Environment

Evolving technologies, as exemplified by computational grids and Web services, have made it possible to solve new scientific problems that would not have been feasible previously. In order to make such advances available to the community in general and to be able to solve new problems, not necessarily from the same discipline, it is imperative to build tools that provide a common user interface in order that application programmers and users do not have to be concerned with particulars of Web services and their underlying code, computational platforms, or with data file formats. We will describe our efforts in creating a computational chemistry environment that encompasses a general scientific workflow environment, a domain specific example for quantum chemistry, our ongoing design of a workflow user interface, and our efforts at database integration.     

Modelization of the whispering gallery mode in microgear resonators using the Floquet-Bloch formalism

In this paper, a two-dimensional (2-D) method describing the whispering gallery mode in a microgear resonator is presented. The microgear is a microdisk surrounded by a circular grating. The method, which is based on the Floquet-Bloch formalism, analytically describes the field within the disk and outside the grating. On the other hand, the field within the grating is calculated using a finite-difference scheme in polar coordinates. Matching the boundary conditions, it is possible to work in a forced oscillation regime or in a free oscillation regime (laser mode). The resonant wavelength and quality factor can then be deduced. Compared to the coupled mode theory and to 2-D finite-difference time-domain computations, the method is faster and more accurate. Moreover, a polarization effect of the microgear is demonstrated. The TE polarization experiences a Q-factor improvement contrary to TM polarization. Finally, microgear structures prove to be more efficient than micro flowers.