Fluidised pellet bed bioreactor: a promising technology for onsite wastewater treatment and reuse.

A pilot-scale fluidised pellet bed (FPB) bioreactor, which combines chemical coagulation, biological degradation, particle pelletisation and separation in one unit, was applied for onsite wastewater treatment and reuse. As a result of rational use of inorganic coagulant and organic polymer and moderate mechanical agitation, spherical particles were generated in the upflow column and a well-fluidised bed was formed. With a continuous supply of dissolved oxygen through a recycling loop, an aerobic condition was kept in the bottom section of the FPB column. Under such conditions the pellets in the FPB column showed the following characteristics: (1) compact structure and high density; (2) rich in microorganisms; and (3) high MLSS and MLVSS concentrations. Therefore, the FPB bioreactor achieved more than 90% removal of SS, COD, BOD and TP from raw domestic wastewater within a total hydraulic retention time (HRT) of only about 30 minutes. It also showed nitrification and denitrification ability and the TN removal could be about 50% as the recycling ratio was increased to 1:1. The treated water quality is generally competitive with the secondary effluent from a conventional activated sludge process. With these advantages the FPB bioreactor is recommendable as a compact system for onsite wastewater treatment and reuse.     

Asynchronous sensorless thyristor electric drive

A speed regulated electric drive for a thyristor voltage converter-induction motor system is presented. The frequency of rotor rotation is determined on the basis of the EMF and the stator voltage     

A video codec LSI for high-definition TV systems withone-transistor DRAM line memories

A video codec LSI for high-definition television (HDTV) systems has been developed. By using a time-compressed integration encoding technique, it converts a 20.0-MHz bandwidth luminance signal and two 5.0-MHz chrominance signals into a compressed image signal at 48.6-MHz sampling frequency. It is useful in many HDTV application systems, such as 400-Mb/s digital transmission system, a video disk player system, or an analog transmission system. Over 288000 elements, including a 52-kb one-transistor DRAM (dynamic random access memory) line memory specially developed for this LSI, were integrated on a 12.16×12.10-mm² chip. A standard cell layout method and a 1.2-μm CMOS logic LSI process were used     

Novel microwave projection imaging for determination of internal structure

A novel microwave imaging technique based on the generalised weighted backprojection operator is introduced and tested using experimental data. Images of the internal structure of penetrable objects using this technique are compared and contrasted with images found from the classical back-projection method. It is demonstrated that the new method provides high-quality images of both discrete and continuous internal structure without the distortions characteristic of traditional methods.     

Heat transfer from a stretching sheet with uniform suction and blowing

Summary The conjugate problem of heat transfer from an accelerating surface in presence of suction and blowing has been solved analytically. The effects of different parameters on cooling of the surface have been discussed.With 3 Figures     

Self-aligned diffusion technique for n-InP JFETs

A self-aligned diffusion process has been demonstrated in the fabrication of n-InP JFETs on semi-insulating InP. This process utilises the anisotropic and selective etching properties of InP/GaInAs materials. Using this technique, sub-micrometre gate lengths can be achieved even with conventional photolithography. Devices with trans-conductance of >35mS/mm, leakage current of < 10nA/mm and gate capacitance of <0.7pF/mm have been fabricated with a cutoff frequency of 7 GHz.     

Slow lowering of pH induces gel formation of myosin

It has been found that solutions of myosin (10 mg/ml) form gels at 5°C if the pH is decreased slowly, by dialysis, to a value in the region of 2.5 to 5.5. Gel strength displays strong dependence on final pH, having a maximum at about pH 4.5. Salt (KCl) concentration was found to affect gel strength positively and linearly. Differential scanning calorimetry revealed that the myosin of pH-induced gels absorbed no thermal energy when heated, implicating acid-induced denaturation as the basis of gel formation. By comparison with heat-induced gelation of myosin and from the fact that low pH is conducive to filament formation, it is suggested that filaments may also be involved in the gelation process.     

Microstructure evolution during mechanical working of three RS aluminium alloys: Al-4Cr-1Fe,Al-5Cr-2Zr and Al-6.43Cr-1.67Zr

Three Al-Cr alloys containing additions of Zr and Fe have been fabricated via cold compaction and hot extrusion. The decomposition of the powder microstructure and the subsequent coarsening during thermomechanical treatment have been studied. Detailed electron microscopy investigations were performed at different locations of partially extruded billets at 450 °C. The microstructure of the dead metal zone reflects the effect the induction heating exerts on the as-atomized powder microstructure. In the low Cr alloys, Al-4Cr-1 Fe and Al-5Cr-2Zr, decomposition of the rapidly solidified microstructure commences at the rich intercellular network, whereas the microstructure of the Al-6.43Cr-1.67Zr alloy remains relatively unaffected. Within the deformation zone the precipitation kinetics are affected by the shearing and the temperature rise. The cells and the powder particles are aligned along the extrusion direction. Precipitation is taking place within the primary segregation-free areas, observed in Al-4Cr-1 Fe and Al-5Cr-2Zr alloys, whereas in the Al-6.43Cr-1.67Zr alloy, decomposition of the powder microstructure starts at the Cr-rich intermetallic particles. The as-extruded microstructure is fibrous and heterogeneous. The heterogeneity of the as-extruded microstructure is a result of the microstructural variation observed within different size powder particles and within individual ones.     

Integrated modelling under uncertainty in watershed-level assessment and management.

Uncertainty in water quality model predictions is inevitably high due to natural stochasticity, model uncertainty, and parameter uncertainty. An integrated modelling system (modified-BASINS) under uncertainty is described and demonstrated for use in receiving-water quality prediction and watershed management. A Monte Carlo simulation was used to investigate the effect of various uncertainty types on output prediction. Without pollution control measures in the watershed, the concentrations of total nitrogen (T-N) and total phosphorus (T-P) in the Hwaong Reservoir, considering three uncertainty types, would be less than about 4.4 and 0.23 mg L(-1), respectively, in 2012, with 90% confidence. The effects of two watershed management practices, wastewater treatment plants (WWTP) and constructed wetlands (WETLAND), were evaluated. The combined scenario (WWTP + WETLAND) was the most effective at improving reservoir water quality, bringing concentrations of T-N and T-P in the Hwaong Reservoir to less than 3.4 and 0.14 mg L(-1), 24 and 41% improvements, respectively, with 90% confidence. Overall, the Monte Carlo simulation in the integrated modelling system was practical for estimating uncertainty and reliable in water quality prediction. The approach described here may allow decisions to be made based on the probability and level of risk, and its application is recommended.