Deformation behavior and microstructure of an Al-Zn-Mg-Cu-Zr alloy during hot deformation

The hot deformation behavior and microstructures of Al-7055 commercial alloy were investigated by axisymmetric hot compression at temperatures ranging from 300°C to 450°C and strain rates from 10-2 to 10 s-1,respectively.Microstructures of deformed 7055 alloy were investigated by transmission electron microscopy (TEM).The dependence of peak stress on deformation temperature and strain rate can be expressed by the hyperbolic-sine type equation.The hot deformation activation energy of the alloy is 146 kJ/mol....     

Improved response surface method based on sample point selection strategies

In the reliability analysis of complex structures,response surface method(RSM)has been suggested as an efficient technique to estimate the actual but implicit limit state function.A set of sample points are needed to fit to the implicit function.It has been noted that the accuracy of RSM depends highly on the so-called sample points.However,the technique for point selection has had little attention.In the present study,an improved response surface method(IRSM)based on two sample point selection techniques,named the direction cosines projected strategy(DCS)and the limit step length iteration strategy(LSS),is investigated.Since it uses the sampling points selected to be located in the region close to the original failure surface,and since it needs only one response surface,the IRSM should be accurate and simple in practical structural problems.Applications to several typical examples have helped to elucidate the successful working of the IRSM.     

采用优化的腐蚀工艺对TiSi2接触特性的改善

针对传统TiSi_2工艺中RCA1(NH_4OH:H_2O_2:H_2O)溶液对于TiN/Ti与TiSi_2的选择性不好会造成硅化物的损失、提高接触电阻的问题,提出一种采用2次选择性腐蚀的工艺方法进行改善.通过具体的工艺实验证明,与传统工艺方法相比,该工艺方法可以在保持低漏电流的前提下,有效减少TiSi_2的损失,使得方块电阻降低约18%.该工艺方法具有简单易行的特点,适用于大规模工业生产.     

煤岩组成与水煤浆成浆性能的关系研究

为了考察煤岩组成对成浆性能的影响,以惰质组含量较高的神府榆家梁煤为研究对象,采用重液离心法进行煤岩组分的分离和富集,配制出具有不同煤岩组成的制浆用模型煤样,然后在相同的条件下进行制浆试验,研究得出了煤岩组成与成浆性的定量关系.结果表明:成浆性随惰质组含量的增加和镜质组舍量的减少而先增加后降低,对于本试验所用的神府榆家梁煤,当惰质组含量大约为24%时制浆效果最好.     

油气管道堵塞检测及定位技术研究

针对油气输送管道中的堵塞现象,提出利用管道堵塞前后两端压差的剧烈变化,以及利用管道两端压力的模拟值与实际测量值的差异来检测管道的堵塞,提出通过检测管道水力坡降曲线奇异点的方法确定油气管道的堵塞位置的原理和方法,通过采集管道两端运行参数,并建立管道运行的数学模型,对管道实施仿真,获得整条管线的水力坡降曲线,再应用小波变换对管道的水力坡降曲线进行奇异性检测,而管道水力坡降曲线的奇异点将对应管道的堵塞位置.该方法具有所需设备少,操作费用低,操作简单等优点,优于现有管道堵塞位置确定方法.     

天然气管道事故严重度评价体系研究

为解决由于天然气管道管材的老化、腐蚀以及外力破坏引发事故的评价问题,以目标层、准则层和指标层3层结构体系,构建了天然气管道事故严重度评价体系,该体系从管道类型、事故类型、事故发生地点和事故已有损失4个方面来评价事故的严重程度,采用百分制权重加和法得到事故严重度指标值G,依据G值大小将事故分为3个等级,评估结果可以为管理层提供参考,为制定天然气管道事故抢修抢险方案起到导向作用.     

H型截面单层单跨钢框架火灾行为试验

对2榀H型截面单层单跨钢框架进行了火灾行为的足尺试验研究.全部试验采用自行研制的火灾试验炉,试验结果表明炉子性能稳定,使用方便.试验中考虑了不同受火工况对钢框架火灾行为的影响.通过试验得出了钢框架温度场分布和变形的变化规律.试验结果表明:火灾下,梁柱全部受火的单层单跨钢框架(节点受到保护)破坏方式为钢柱压屈破坏,破坏位置在受到保护的钢节点下部的钢柱上.试验研究为今后钢结构火灾行为的研究提供依据.     

＂Nonlinear＂ characteristics of the static earth pressure coefficient in thick alluvium

Exact calculations of the static earth pressure from a thick alluvium require accurate K0 values. These calculations influence the sinking cost and the safety of the freezing method. The static earth pressure coefficient (K0) of thick and deep soil was analyzed using laboratory tests. The results show that the static earth pressure coefficient of thick and deep soils is nonlinear and different from that of superficial soils. The constant of superficial soils is usually invariant and the total stress or incremental stress definitions used in traditional geo-mechanics give the same value. The influence of load increments when calculating for superficial soil is ignored. The difference in values of K0 for thick alluvium defined by the total stress or the incremental stress methods is over 10%. The effects of the thick alluvium on K0 should be considered during the design of frozen shaft projects. Such things as the frozen shaft thickness and the excavated section height should be chosen to assure the rationality of the design and to avoid potential faults and accidents.     

微藻固定高浓度CO2技术的研究进展

自工业革命以来,不断增长的燃料消耗导致大气中CO2浓度日益升高,由此所产生的温室效应已经受到全世界的普遍关注.近年来,国际上已经开展了生物固碳技术的相关研究.详细介绍了目前国内外利用微藻固定高浓度CO2技术的研究现状.