Finite difference method for dynamic response analysis of anchorage system简

Based on some assumptions, the dynamic analysis model of anchorage system is established. The dynamic governing equation is expressed as finite difference format and programmed by using MATLAB language. Compared with theoretical method, the finite difference method has been verified to be feasible by a case study. It is found that under seismic loading, the dynamic response of anchorage system is synchronously fluctuated with the seismic vibration. The change of displacement amplitude of material points is slight, and comparatively speaking, the displacement amplitude of the outside point is a little larger than that of the inside point, which shows amplification effect of surface. While the axial force amplitude transforms considerably from the inside to the outside. It increases first and reaches the peak value in the intersection between the anchoring section and free section, then decreases slowly in the free section. When considering damping effect of anchorage system, the finite difference method can reflect the time attenuation characteristic better, and the calculating result would be safer and more reasonable than the dynamic steady-state theoretical method. What is more, the finite difference method can be applied to the dynamic response analysis of harmonic and seismic random vibration for all kinds of anchor, and hence has a broad application prospect.     

导磁体在汽车零件感应加热中的应用技术

本文简单介绍了导磁体工作的基本原理，并给出在汽车零件大规模生产中所积累的导磁体应用的一些经验，以阐明如何更有效地使用导磁体。     

Oxidation behavior and mechanism of aluminum oxynitride (AlON) at elevated temperatures

The oxidation behavior and mechanism of aluminum oxynitride (AlON) powder exposed to air at elevated temperatures between 800°C and 1300°C was investigated by X-ray diffractometry (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), nuclear magnetic resonance (NMR), and simultaneous thermogravimetry, differential thermal analysis, and mass spectrometry techniques (TG-DTA-MS). The weight of AlON gradually increases to a maximum value at 1150°C and then decreases with further heating. Meanwhile, AlON powder undergoes chemical changes, as evidenced by lattice expansion, and turns eventually into alumina. ESR spectra reveal the occurrence of lone pair electrons in the oxidized products and the intensity of corresponding resonance signal increases before disappearing with the increase in temperature. Combined with the results of NMR and TG-DTA-MS, the measured data suggest that Al-N in [AlO₃N] tetrahedron and [AlO₅N] octahedron are gradually oxidized into Al-O-N group with lone pair electrons, which causes continuous weight gain and lattice expansion. Further oxidation at higher temperatures results in alumina and N₂.     

用含Pb、As、Sn地方生铁砂型铸造生产D型石墨铸铁的研究

基于Ph、As、Sn等元素有增大铁液过冷倾向的作用，利用含Ph、As、Sn的地方生铁，采用合金化和砂型铸造可以获得D型石墨铸铁，对其工艺方案进行了研究。用正交试验法设计试验方案，得到最佳工艺方案为：在亚共晶成分（WB％：3．2C，2．1si）的铁液中加入适量的铝（0．6％）和钛（0．8％），可以得到含有100％D型石墨的铸铁，其抗拉强度最高可达276MPa。     

Electrochemical properties of some cobalt antimonides as anode materi-als for lithium- ion batteries

Some cobalt antimonides have been prepared and studied as the candidate anode materials for lithium ion batter-ies. Reversible capacities of 424,423 and 546 mA·h·g-1 were measured at the first cycle for as-solidified CoSb2, CoSb3 and annealed CoSb3 respectively. A low lithium ions diffusion coefficient in the order of 10-16 m2·s-1 was estimated from the coulometric titration measurements in the annealed CoSb3 electrode. It was found that the electrochemical properties of fine powders are significantly better than coarse powders. However the SEM picture shows that the nano-sized CoSb3 powders gathered to larger granules, which worsens somewhat the capacity retention of the nano-sized materials, although the volume capacities of the annealed and ball milled CoSb3 remain near twice of that of graphite after 50 cycles.     

易门铜业公司18kt／a粗铜及硫酸车间的技改工程

介绍了易门铜冶炼厂烟气制酸系统的技术改造工程.从工艺流程、设备复核、工艺参数、设备配置等方面阐述了技改的过程.     

钨钴硬质合金电化学蚀刻加工研究

对YG6硬质合金电化学蚀刻工艺进行了研究,提出了采用光致抗蚀剂作保护膜,在生成一定钝化膜的情况下进行电化学蚀刻的方法.在一定的蚀刻深度范围内,该工艺的可控性好、腐蚀区表面质量较好.     

模式识别方法研究影响转炉炼钢脱磷的因素

利用模式识别方法中的偏最小二乘法对转炉炼钢的磷分配比及主要影响因素进行了分析 ,用二维分类图给出了优化趋势 ,结果符合一般脱磷理论和实际 ,可以作为冶炼的参考。     

含B2O3渣系的热力学计算模型

根据炉渣结构的共存理论和相图，推导了ＣａＯＢ２Ｏ３和ＦｅＯＦｅ２Ｏ３Ｂ２Ｏ３渣系的热力学计算模型。结果表明：（１）理论计算的ＣａＯＢ２Ｏ３渣系的作用浓度ＮＣａＯ及ＮＢ２Ｏ３与实测的活度ａＣａＯ及ａＢ２Ｏ３一致；（２）理论计算的ＦｅＯＦｅ２Ｏ３Ｂ２Ｏ３渣系的氧化能力ＮＦｅｔＯ与实测的炉渣ＦｅｔＯ的活度值相符合。这说明本文提出的热力学计算模型是合理的。     

施工环境下无线网络测试方案

专业无线网络测试方案,测试环境苛刻,测试技术复杂,不便于施工现场进行测试。为了快速定位施工现场无线网络的运行状态,通过对无线网络技术的深入了解,以具体项目为契机,以发现并解决无线网络出现的问题为目的,制定详尽的无线网络测试方案,得出无线网络测试结果,分析结果得出网络出现的问题并解决。