热压烧结Ti3AlC2材料的制备、结构与性能研究

采用热压工艺研究了不同工艺制度和原料中不同的Si含量对Ti3AlC2合成的影响.研究表明在1 300℃～1 500℃,30MPa压力和Ar气氛中热压摩尔比为n(TiC)n(Ti)n(Al)n(Si)=2110.2的混合粉末,可以得到纯度达98%(质量分数)以上的致密块体Ti3AlC2材料;添加的Si均匀分布在基体中,形成固溶体,当添加Si的摩尔比为0.2时,固溶体的化学式为Ti2 76Al0 78Si0.22C2.烧结试样的晶体为层片状结构,1 300℃和1 400℃时,烧结试样的晶粒尺寸分别为10μm～15μm和20μm～30μm.材料的维氏硬度为3.3 GPa～5.0 GPa,弹性模量为289 GPa,抗压强度为785 MPa,抗弯强度为375 MPa,断裂韧性为7.0 MPa·m1/2;25℃时,电导率为3.1×106 S·m-1,热容为125.4 J/mol·K,热导率为27.5 W/m·K;热膨胀系数为8.8×10-6 K-1.     

Zr－1Nb合金吸氢性能研究

研究了１３种不同加工热处理制度的Ｚｒ－１Ｎｂ合金在堆外高压釜内３６０℃、１９ＭＰａ水中的吸氢性能，对其影响因素和吸氢机理进行了分析，并讨论了吸氢动力学，建立了吸氢动力学方程，计算了吸氢动力学参数。     

Electrochemical Study on Formation of Dy-Ni Alloy in Molten Chlorides

ＥｌｅｃｔｒｏｃｈｅｍｉｃａｌＳｔｕｄｙｏｎＦｏｒｍａｔｉｏｎｏｆＤｙ－ＮｉＡｌｌｏｙｉｎＭｏｌｔｅｎＣｈｌｏｒｉｄｅｓＴｏｎｇＹｅｘｉａｎｇ；ＬｉｕＧｕａｎｋｕｎ；ＹａｎｇＱｉｑｉｎ；ＨｏｎｇＨｕｉｃｈａｎ，（童叶翔）（刘冠昆）（杨绮琴）（洪惠婵）...     

我国火电锅炉和电站用钢管的现状与发展

介绍了我国火电锅炉和电站用钢管的现状，以及国内外发展趋势。     

LX—2型变频式喂线设备的研制及应用

根据炼钢生产的实际需要,分析了喂线技术的工艺要求,介绍了所研制的LX－2型变频式喂线机的结构特点,指出了影响喂线机使用效果的因素,并提出了若干措施。     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

基于Rough集的磨削参数决策系统

本文介绍了5层模糊神经网络的优缺点，提出了基于Rough集构造模糊神经网络的方法，并应用于多传感器的磨削参数决策系统，达到控制磨削加工质量的目的。     

冶金工业的发展及其对冶金轧辊的需求

从冶金工业的发展现状可知高质量的轧辊仍是一个很大的市场。高速钢轧辊具有很强的竞争力。离心铸造法生产高速钢轧辊是主要的工艺方法。     

Structural stability of single-layered LaNi4.25Al0.75 film and its electrochemical hydrogen-storage properties

AB5-based hydrogen storage thin fdms （LaNi4.25Al0.75）, deposited on Cu substrate by dc magnetron sputtering were investigated in this study. X-ray diffraction （XRD） revealed that the microstructure of the layer was in crystal form. SEM and AFM analyses proved that the film appeared to be rather rough with numerous randomly sized pores of approximately 15-40 in nm diameter. Structural stability of the film was examined by the combined analyses of DSC, XRD, and SEM, which indicated that this film maintained its structural stability below 500 K or so, and a network structure was observed on the film after being heated at 700 K for 30 min. Electrochemical hydrogen-storage properties of the films were investigated by simulated battery tests. It was found that single-layered LaNi4.25A10.75 film exhibited electrochemical hydrogen-storage properties similar to typical AB5 alloys in bulk, and the maximum discharge capacity of the film was about 220 mAh/g. After 20 charge/discharge cycles, small needle-shaped aluminium oxide was formed on some fractions of the film surface.     

均苯四甲酸铕发光配合物的合成与表征

在乙醇和水的混合溶剂中合成了均苯四甲酸(H4L)铕发光配合物。通过元素、化学分析、红外光谱确定其化学组成为Eu4/3L·7H2O。热分析表明,配合物在530℃以下稳定性较好,X射线衍射结果表明,配合物为晶体物质,扫描电镜照片表明配合物为块状物质,晶粒10μm-20μm,荧光光谱分析表明配合物在紫外光的激发下发出铕的特征荧光。