Novel biocatalysts: Recent developments

The limited number of suitably well characterized biocatalysts continues to limit progress in the application of biological routes in the synthesis of compounds for novel pharmaceuticals, materials, or performance chemicals. In this situation, the discovery of novel biocatalysts or novel functionalities or substrates on existing ones is an important task. This work describes a range of novel biocatalysts obtained recently through one of three techniques: environmental sampling or screening, protein engineering on existing enzymes, or extension of the catalytic profile of existing catalysts.     

Reactions of glycerol with poly(ethylene ether carbonate) polyols

Poly(ethylene ether carbonate) polyols can be modified by chemical reactions with polyglycol modifiers under conditions of elevated temperatures and reduced pressures. The modifier becomes chemically incorporated into the modified polyol and is used to control properties such as moisture sensitivity, CO₂ content, T_g, density, etc. in the resultant polyol. However, glycerol cannot be used as a modifier for poly(ethylene ether carbonate) polyols under the same conditions since it reacts with poly(ethylene ether carbonate) polyols by a transesterification reaction sequence to form glyceryl carbonate. As the temperature is increased, the glyceryl carbonate decomposes to yield glycidol and carbon dioxide. These reactions are conveniently followed by ¹³C-NMR. The preparation of glyceryl carbonate by this process has not been previously reported.     

Application of image analysis based on SEM and chemical mapping on PC mortars under sulfate attack

The degradation mechanisms of cementitious materials exposed to sulfate solutions have been controversial, despite considerable research. In this paper, two methodologies of image analysis based on scanning electron microscope and chemical mapping are used to analyse Portland cement mortars exposed to sodium sulfate solution. The effects of sulfate concentration in solution and water to cement ratio of mortar, which are considered as the most sensitive factors to sulfate attack, are investigated respectively by comparing the macro expansion with microstructure analysis. It is found that the sulfate concentration in pore solution, expressed as sulfate content in C-S-H, plays a critical role on the supersaturation with respect to ettringite and so on the expansion force generated.     

Combination of the Elevated Stearic Acid Trait with Other Fatty Acid Traits in Soybean

Stearic acid is one of five major fatty acids found in soybean oil. It is a fully saturated lipid and is known for neutral or positive effects on LDL cholesterol when consumed by humans. Unfortunately, stearic acid only accounts for about 4% of the total seed oil produced in commodity soybean. Previous work has shown that stearic acid can reach levels as high as 28% of the total oil fraction when the SACPD-C gene, encoding the delta-9-stearoyl-acyl carrier protein desaturase responsible for most of the stearic acid variation in soybean seed, is ablated in combination with other loci. In order to increase stearic acid content and create soybeans with improved utility based on fatty acid composition, we combined mutations in SACPD-C with other mutations in the fatty acid biosynthetic pathway. Soybean plants carrying mutant alleles of both SACPD-C and FAD2-1A produce seed with stearic acid levels from 14% to 21%, and with elevated levels of oleic acid. Soybeans carrying mutations in both SACPD-C and FAD3A or FAD3C have both statistically significantly elevated levels of stearic acid (from 15–21%) and statistically reduced linolenic acid levels. Neither mutant combination appears to affect other agronomic properties such as plant morphology or seed protein levels making this a potentially viable trait.     

Chemical and morphological effects of blended sulfonated poly(styrene-isobutylene-styrene) and isopentylamine for direct methanol fuel cell applications

In this study, blend membranes based on a combination of sulfonated poly (styrene-isobutylene-styrene) (SIBS) with isopentylamine (IPA) were synthetized as potential candidates for direct methanol fuel cell (DMFC) applications. The impact of sulfonation level (57–93 mol%) and percentage of IPA incorporation (1, 3, and 5 wt%) were analyzed via different properties of the resulting membrane. FTIR analysis showed that IPA was successfully incorporated into the sulfonated polymer matrix and also confirmed the interaction between the sulfonic and amine groups. This interaction generates significant morphological changes in the nanostructure of the membranes that are evident through results of small angle x-ray scattering and atomic force microscopy analysis. Proton conductivity and methanol permeability of the membranes were also analyzed. Proton conductivity was significantly enhanced with the incorporation of IPA at an optimum loading, creating additional paths for the conduction of protons through the membrane. It was also sensitive to the morphological changes produced after the IPA incorporation and the interconnection between the ionic domains. Methanol permeability increased slightly due to the additional water domains and the inability of the isopentyl groups of IPA to block the free-volume in the membrane. Despite this, the selectivity (proton conductivity over methanol permeability) of the membranes was comparable to the state-of-the-art Nafion®, especially at an optimum IPA incorporation of 3 wt%.     

Effect of substrate surface roughness on the adherence of NiCrAlY thermal spray coatings

The adherence of plasma sprayed NiCrAlY bond coats can be improved by an appropriate substrate surface finish. The interface fracture energy for crack propagation along the coating/substrate interface has been measured for different surface roughness by means of a specially designed four-point bending test. An increase of the interface fracture energy of about 15% was observed for a three times higher surface roughness. In addition, four-point bending tests with the coating on the side face of bending specimens were performed to analyze the fracture and spalling behavior of the coatings both under large tensile and compressive substrate deformations.     

Design considerations for highly efficient edge‐lit quantum dot displays

Quantum dots (QDs) are increasingly the technology of choice for wide color gamut displays. Two popular options to incorporate QDs into displays include on‐edge and on‐surface solutions. The opto‐mechanical design for an on‐edge QD solution including a LED light bar (“on‐edge QD light bar”) is more complex than the design for a standard white phosphor LED light bar. In this paper, we identify and investigate a range of design parameters for an on‐edge QD light bar, and we show that these parameters have significant influence on system efficiency and color uniformity. The effects of varying these parameters are explored through the use of a custom adjustable testbed and optical raytracing methods. Our testbed data demonstrate the inherent trade‐offs between efficiency and color uniformity and provide guidance for the design of high‐performing displays. The optical raytracing data demonstrate a good predictive capability and support the use of optical modeling methods for a detailed exploration of a wider range of design parameters.     

Development of a high pressure automated lag time apparatus for experimental studies and statistical analyses of nucleation and growth of gas hydrates

Nucleation in a supercooled or a supersaturated medium is a stochastic event, and hence statistical analyses are required for the understanding and prediction of such events. The development of reliable statistical methods for quantifying nucleation probability is highly desirable for applications where control of nucleation is required. The nucleation of gas hydrates in supercooled conditions is one such application. We describe the design and development of a high pressure automated lag time apparatus (HP-ALTA) for the statistical study of gas hydrate nucleation and growth at elevated gas pressures. The apparatus allows a small volume (≈150 μl) of water to be cooled at a controlled rate in a pressurized gas atmosphere, and the temperature of gas hydrate nucleation, T(f), to be detected. The instrument then raises the sample temperature under controlled conditions to facilitate dissociation of the gas hydrate before repeating the cooling-nucleation cycle again. This process of forming and dissociating gas hydrates can be automatically repeated for a statistically significant (>100) number of nucleation events. The HP-ALTA can be operated in two modes, one for the detection of hydrate in the bulk of the sample, under a stirring action, and the other for the detection of the formation of hydrate films across the water-gas interface of a quiescent sample. The technique can be applied to the study of several parameters, such as gas pressure, cooling rate and gas composition, on the gas hydrate nucleation probability distribution for supercooled water samples.     

Water Governance in Canada: Innovation and Fragmentation

This paper explores Canada's approach to water governance. It argues that fragmented governance has had negative impacts on Canada's ability to manage water resources adequately (particularly in the context of urbanization, agriculture and resource extraction), and to deal with new issues (such as climate change). Further, it argues that Canada's highly decentralized approach to water governance creates challenges of integration, coordination and data availability. The paper explores possible future strategies for innovations in water governance that may have the potential to improve water management outcomes.