Efficiently Releasing the Trapped Energy Flow in White Organic Light‐Emitting Diodes with Multifunctional Nanofunnel Arrays

White organic light‐emitting diodes (OLEDs) hold great promise for applications in displays and lighting due to high efficiency and superior white color balance. However, further improvement in efficiency remains a continuous and urgent demand due to limited energy flow extraction. A powerful method for drastically releasing the trapped energy flow in conventional white OLEDs is demonstrated by implementing unique quasi‐periodic subwavelength nanofunnel arrays (NFAs) via soft nanoimprinting lithography, which is ideal for enhancing light extraction without any spectral distortion or angular dependence. The resulting efficiency is over 2 times that of a conventional OLED used as a comparison. The external quantum efficiency and power efficiency are raised to 32.4% and 56.9 lm W^?1, respectively. Besides, the substantial increase in efficiency over a broad bandwidth with angular color stability, the experimental proofs show that the NFA‐based extraction structure affords the enticing capacity against scrubbing and the self‐cleaning feature, which are critical to the commercial viability in practical applications.     

铝合金激光-MIG复合焊接头性能研究

探讨了激光与电弧相互作用后,焊缝中心上部和下部晶粒大小不同的原因,在此基础上研究了焊接速度的改变对6009铝合金接头的微观组织、拉伸性能、显微硬度的影响。结果表明：6009铝合金激光-MIG焊焊接接头的抗拉强度和延伸率随着焊接速度的增加而增加,拉伸试样的断裂位置由焊缝区转移到热影响区,断口呈现均匀分布的韧窝形貌,断裂机制为微孔聚集形断裂;焊缝中心上部晶粒小于焊缝中心下部,而且尺寸分布均匀。焊缝中心上部的显微硬度则高于焊缝下部。接头热影响区存在软化区,宽度为4～6 mm。     

The impact of horizontal water velocity on the energy consumption of a full‐scale wastewater treatment plant

This study quantifies the impact of the oxidation ditch horizontal water velocity on the energy consumption of a full‐scale wastewater treatment plant (WWTP). A WWTP was modelled by means of the ASM2d platform, showing very good correlation with reference operational data. As to reduce the energy requirements of the plant while guarantying the same nutrient removal performance, two approaches were used. A classical aeration control optimization, yielding a 4% energy reduction, was compared with an increase of the oxidation ditch propelling power. The horizontal water velocity in the oxidation ditches was estimated at only 0.15 m/s. By increasing the horizontal water velocity to 0.3 m/s, an 8% energy reduction could be achieved. Moreover, a synergistic effect for classic control optimization and oxidation ditch water velocity optimization resulted in a 14% energy reduction. Energy spent in propelling power counteracts the aeration energy gain derived by an increase in the oxidation ditch horizontal velocity. An optimum in the water velocity was quantified at 0.3 m/s, comparably with its design value.     

磷石膏料浆专用阀设计

介绍了磷石膏料浆的生产过程及其工况特性,给出了磷石膏料浆专用阀的技术参数、工作原理、结构特点和设计方法。     

An environmental purpose artificial island off Belgium

Processing municipal and industrial wastes on land and particularly near inhabited centra has met with increased opposition. An apparent remedy to the problem is the establishment of such facilities offshore, hence various projects to build them on artificial islands. The paper examines a concrete proposal to locate such an island offshore from the Belgian Coast. Oceanographic and environmental aspects of the site are discussed, construction methods reviewed, erosion and corrosion effects looked at. The possibility of utilizing ocean power to provide the necessary operation energy is likewise considered.     

Degradation of emergent contaminants by UV,UV/H2O2 and neutral photo-Fenton at pilot scale in a domestic wastewater treatment plant

This study focuses on the removal of 22 selected micropollutants in an effluent from a municipal wastewater treatment plant (MWTP) at pilot scale. A reactor of 37 L with five low pressure mercury lamps emitting at 254 nm (UV₂₅₄) was used. The 22 micropollutants include 15 pharmaceuticals, 2 X-Ray contrast medias, 1 corrosion inhibitor and 4 biocides/pesticides. Five of these 22 compounds were used as indicative substances as proposed by the Swiss Federal Office for the Environment (FOEN) (carbamazepine, diclofenac, sulfamethoxazole, benzotriazole and mecoprop).     

Multi-laboratory evaluations of the performance of Catellicoccus marimammalium PCR assays developed to target gull fecal sources

Here we report results from a multi-laboratory (n = 11) evaluation of four different PCR methods targeting the 16S rRNA gene of Catellicoccus marimammalium originally developed to detect gull fecal contamination in coastal environments. The methods included a conventional end-point PCR method, a SYBR^® Green qPCR method, and two TaqMan^® qPCR methods. Different techniques for data normalization and analysis were tested. Data analysis methods had a pronounced impact on assay sensitivity and specificity calculations. Across-laboratory standardization of metrics including the lower limit of quantification (LLOQ), target detected but not quantifiable (DNQ), and target not detected (ND) significantly improved results compared to results submitted by individual laboratories prior to definition standardization. The unit of measure used for data normalization also had a pronounced effect on measured assay performance. Data normalization to DNA mass improved quantitative method performance as compared to enterococcus normalization. The MST methods tested here were originally designed for gulls but were found in this study to also detect feces from other birds, particularly feces composited from pigeons. Sequencing efforts showed that some pigeon feces from California contained sequences similar to C. marimammalium found in gull feces. These data suggest that the prevalence, geographic scope, and ecology of C. marimammalium in host birds other than gulls require further investigation. This study represents an important first step in the multi-laboratory assessment of these methods and highlights the need to broaden and standardize additional evaluations, including environmentally relevant target concentrations in ambient waters from diverse geographic regions.     

Market strategies and core capabilities in the building industry

The objective of this study is to show that the core competence approach has validity when applied to construction. The focus is on the analysis of the fit between market strategies of firms in the building industry and their core capabilities. Certain strategies require specific core capabilities and key external and internal conditions supporting these capabilities. The resource-based approach focuses on the conditions in a firm, the internal capabilities, and supports a core capability that is demanded. The network literature will be related to external conditions that support a core capability of a firm active in a certain market. In a multiple case study, firms are analysed that are involved in different stages of the building process. The case studies demonstrate firms with consistent patterns of market strategies, core capabilities, and supporting internal and external conditions. The specific core capability of the firm under investigation determines the types of external and internal conditions that are critical.