Prediction of the biologically active sites in eclosion hormone from the silkworm, Bombyx mori

The structure-activity relationship of eclosion hormone from the silkworm, Bombyx mori, was analyzed. First, the probable active residues in silkworm eclosion hormone and also tobacco hornworm eclosion hormone were predicted by the average distance map method. To examine the contributions of those residues to the activity of silkworm eclosion hormone, Gly-substituted mutants for those predicted residues were produced by site-directed mutagenesis and their activities were evaluated by a bioassay. Finally, Glu12, Met24 and Phe25 were estimated to be the crucial residues for the eclosion hormone activity. The possibility of the development of a blocker of an eclosion hormone receptor on the basis of the present work is also discussed.      

New class of cellulose fiber spun from the novel solution of cellulose by wet spinning method

A novel cellulose solution, prepared by dissolving an alkali-soluble cellulose, which was obtained by the steam explosion treatment on almost pure natural cellulose (soft wood pulp), into the aqueous sodium hydroxide solution with specific concentration (9.1 wt %) was employed for the first time to prepare a new class of multifilament-type cellulose fiber. For this purpose a wet spinning system with acid coagulation bath was applied. The mechanical properties and structural characteristics of the resulting cellulose fibers were compared with those of regenerated cellulose fibers such as viscose rayon and cuprammonium rayon commercially available. X-ray analysis shows that the new cellulose fiber is crystallographically cellulose II, and its crystallinity is higher but its crystalline orientation is slightly lower than those of other commercial regenerated fibers. The degree of breakdown of intramolecular hydrogen bond at C₃[X_am(C₃)] of the cellulose fiber, as determined by solid-state cross-polarization magic-angle sample spinning (CP/MAS) ¹³C NMR, is much lower than other, and the NMR spectra of its dry and wet state were significantly different from each other, indicating that cellulose molecules in the new cellulose fiber are quite mobile when wet. This phenomenon has not been reported for so-called regenerated cellulose fibers.     

Characteristic properties of cutting fluid additives derived from the adducts of diamines and acid chlorides

A number of N,N′-diacylalkyldiamines were prepared from the reaction of acid chlorides with 1,8-diaminooctane and 1,12-diaminododecane and screened for anti-rust properties and antimicrobial activity in spent coolants of water-based cutting fluids. Aqueous solutions of N,N′-dihexanoyl-1,8-diaminooctane and N,N′-isobutyroyl-1,12-diaminododecane showed good anti-rust properties for water-based cutting fluids. Aqueous emulsions of N,N′-dibutyroyl-, dipentanoyl-, dihexanoyl- and dioctanoyl-1,12-diaminododecane showed good lubricities and antimicrobial activity for water-based cutting fluids.     

Crystal Structure and Microwave dielectric Properties of Ba(Zn1/3Ta2/3)O3–(Sr,Ba)(Ga1/2Ta1/2)O3 Ceramics

The microwave dielectric properties and crystal structure of Ba(Zn_1/3Ta_2/3)O₃– (Sr,Ba)(Ga_1/2Ta_1/2)O₃ ceramics were investigated in the present study. The Q value of Ba(Zn_1/3Ta_2/3)O₃ was improved by adding 5 mol% Sr(Ga_1/2Ta_1/2)O₃. The maximum Q value of Q × f = 162000 GHz was obtained at 0.95Ba(Zn_1/3Ta_2/3)O₃. 0.05Sr(Ga_1/2Ta_1/2)O₃. For this composition, a lattice super structure caused by hexagonal ordering was observed. A further improvement in the Q value was attained when some Sr was replaced with Ba, and 0.95Ba(Zn_1/3Ta_2/3)O₃· 0.05(Sr_0.25Ba_0.75)(Ga_1/2Ta_1/2)O₃ exhibited a maximum Q value such that Q × f = 210000 GHz. Despite the increased Q value with the replacement of Sr by Ba, the c/a value, which indicates the degree of lattice distortion, remained constant near 3/2. The Q value thus improved without lattice distortion in the system Ba(Zn_1/3Ta_2/3)O₃-(Sr,Ba)(Ga_1/2Ta_1/2)O₃, whereas the improvement of Q value increased with lattice distortion in the solid solution system with Ba(Zn_1/3Ta_2/3)O₃ as an end member.     

Anatase-Type TiO2 and ZrO2-Doped TiO2 Directly Formed from Titanium(III) Sulfate Solution by Thermal Hydrolysis: Effect of the Presence of Ammonium Peroxodisulfate on their Formation and Properties

Anatase-type TiO₂ powder containing sulfur with absorption in the visible region was directly formed as particles with crystallite in the range 15–88 nm by thermal hydrolysis of titanium(III) sulfate (Ti₂(SO₄)₃) solution at 100°–240°C. Because of the presence of ammonium peroxodisulfate ((NH₄)₂S₂O₈), the yield of anatase-type TiO₂ from Ti₂(SO₄)₃ solution was accelerated, and anatase with fine crystallite was formed. Anatase-type TiO₂ doped with ZrO₂ up to 9.8 mol% was directly precipitated as nanometer-sized particles from the acidic precursor solutions of Ti₂(SO₄)₃ and zirconium sulfate in the presence and the absence of (NH₄)₂S₂O₈ by simultaneous hydrolysis under hydrothermal conditions at 200°C. By doping ZrO₂ into TiO₂ and with increasing ZrO₂ content, the crystallite size of anatase was decreased, and the anatase-to-rutile phase transformation was retarded as much as 200°C. The anatase-type structure of ZrO₂-doped TiO₂ was maintained after heating at 1000°C for 1 h. The favorable effect of doping ZrO₂ to anatase-type TiO₂ on the photocatalytic activity was observed.     

Porous poly(L‐lactic acid)/poly(ethylene glycol) blend films

Poly(L ‐lactic acid) (PLLA: M_w = 19.4 × 10⁴)/poly(ethylene glycol) (PEG: M_w = 400) blend films were formed by use of a solvent‐cast technique. The properties and structures of these blend films were investigated. The Young's modulus of the PLLA decreased from 1220 to 417 MPa with the addition of PEG 5 wt %, but the elongation at break increased from 19 to 126%. The melting point of PLLA linearly decreased with increases in the PEG content (i.e., pure PLLA: 172.5°C, PLLA/PEG = 60/40 wt %: 159.6°C). The PEG 20 wt % blend film had a porous structure. The pore diameter was 3–5 μm. The alkali hydrolysis rate of this blend film was accelerated due to its porous structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 965–970, 2004     

High-power hybrid plasma spraying of large yttria-stabilized zirconia powder

To testify to the advantage of large ceramic powder spraying, numerical simulations and experimental studies on the behavior of large yttria-stabilized zirconia (YSZ) powder in a high-power hybrid plasma spraying process have been carried out. Numeric predictions and experimental results showed that, with the high radio frequency (RF) input power of 100 kW, the most refractory YSZ powder with particle sizes as large as 88 μm could be fully melted and well-flattened splats could be formed. A large degree of flattening (ξ) of 4.7 has been achieved. The improved adhesive strength between the large splat and the substrate was confirmed based on the measurement of the crack density inside of the splats. A thick YSZ coating >300 μm was successfully deposited on a large CoNiCrAlY-coated Inconel substrate (50×50×4 mm in size). The ultradense microstructure without clear boundaries between the splats and the clean and crack-free interface between the top-coat and the bond-coat also indicate the good adhesion. These results showed that highpower hybrid plasma spraying of large ceramic powder is a very promising process for deposition of highquality coatings, especially in the application of thermal barrier coatings (TBCs).     

Mean–variance relationship of the number of flows in traffic aggregation and its application to traffic management

We consider the mean–variance relationship of the number of flows in traffic aggregation, where flows are divided into several groups randomly, based on a predefined flow aggregation index, such as source IP address. We first derive a quadratic relationship between the mean and the variance of the number of flows belonging to a randomly chosen traffic aggregation group. Note here that the result is applicable to sampled flows obtained through packet sampling. We then show that our analytically derived mean–variance relationship fits well those in actual packet trace data sets. Next, we present two applications of the mean–variance relationship to traffic management. One is an application to detecting network anomalies through monitoring a time series of traffic. Using the mean–variance relationship, we determine the traffic aggregation level in traffic monitoring so that it meets two predefined requirements on false positive and false negative ratios simultaneously. The other is an application to load balancing among network equipments that require per-flow management. We utilize the mean–variance relationship for estimating the processing capability required in each network equipment.     

Current control of a PWM power amplifier by an approximate 2-degree-of-freedom digital controller

There is a need for robust current control of a pulse width modulation (PWM) power amplifier whose transient response characteristics do not deteriorate with extensive load changes and/or direct-current power supply voltage changes. In this article, we propose a digital robust controller with bumpless mode switching to control the current of a PWM power amplifier to satisfy the demands and extend the range of an inductive load width. It is necessary to measure the value of the load in order to implement this bumpless mode switching automatically depending on the load range. Therefore, a method of estimating the inductive load is shown. The bumpless mode switching is automatically performed by estimating an inductive value without specifying the value of the inductive load beforehand. That is, the value of the inductive load is estimated during the DDC execution, and the control mode is automatically switched bumplessly according to this estimated value. A digital controller equipped with inductance estimation and bumpless mode switching is realized by a DSP. Some experiments show that the digital controller with the proposed bumpless mode switching can satisfy larger specifications.