A 1.3-GHz fifth-generation SPARC64 microprocessor

A fifth-generation SPARC64 processor is fabricated in 130-nm partially depleted silicon-on-insulator CMOS with eight layers of Cu metallization. At V/sub dd/ = 1.2 V and T/sub a/ = 25/spl deg/C, it runs at 1.3 GHz and dissipates 34.7 W. The chip contains 191 M transistors with 19 M logic circuits in an area of 18.14 mm /spl times/ 15.99 mm and is covered with 5858 bumps, of which 269 are for I/O signals. It is mounted in a 1360-pin land-grid-array package. The 16-byte-wide system bus operates with a 260-MHz clock in single-data-rate or double-data-rate modes. This processor implements an error-detection mechanism for execution units and data path logic circuits in addition to on-chip arrays to detect data corruption. Intermittent errors detected in execution units and data paths are recovered via instruction retry. A soft barrier clocking scheme allows amortization of the clock skew and jitter over multiple cycles and helps to achieve high clock frequency. Tunability of the clock timing makes timing closure easier. A relatively small amount of custom circuit design and the use of mostly static circuits contributes to achieve short development time.     

Solution‐Processed Silicane Field‐Effect Transistor: Operation Due to Stacking Defects on the Channel

2D silicon nanomaterials have unique potential for use in applications owing to their many different exotic electronic properties. Field‐effect transistors are fabricated based on free‐standing silicanes through a solution process. Owing to the sensitive surface and the nanometer thickness, the devices require the use of fabrication conditions similar to those of lithium‐ion batteries to prevent oxidation of the sheets. Reliable transistor performance is observed at room temperature in a channel thinner than 3 nm, as drain voltage dependent transfer curves current modulation, depending on the edge effect of the silicane, although the transistor property is modest (hole mobility of 1.8 cm² V^?1 s^?1). The results suggest the feasibility of other air‐sensitive 2D nanomaterials for applications in nanoelectronic devices.     

Subcellular localization of fructosyl amino acid oxidases in peroxisomes of Aspergillus terreus and Penicillium janthinellum

Fructosyl amino acid oxidase (FAOD) is the enzyme catalyzing the oxidative deglycation of Amadori compounds, such as fructosyl amino acids, yielding the corresponding amino acids, glucosone, and H(2)O(2). In a previous report, we determined the primary structures of cDNAs coding for FAODs from two fungal strains Aspergillus terreus AP1 and Penicillium janthinellum and we found that both fungal FAODs included the putative peroxisome targeting signal 1 (PTS1) at the carboxyl terminal (Yoshida, N. et al., Eur. J. Biochem., 242, 499-505, 1996). In this study, we determined the intracellular localization of FAODs in these two fungi. Subcellular fractionation experiments and immuno-electronmicroscopic observations, together with the previous findings indicated that the FAODs were localized in peroxisomes of A. terreus AP1 and P. janthinellum. These FAODs were also found to belong to a new member of "peroxisomal sarcosine oxidase family protein" in eucaryotic cells.     

Reliability of Liquid Crystal Display

This paper reports the reliability of twisted nematic liquid-crystal display for basic applications such as watches and calculators. We have studied significant stress factors such as voltage, temperature and humidity, and their corresponding failure modes. The main failure mode is LCD misalignment; many different modes appear corresponding to different stress conditions as well as material and process for the LCD. We have analyzed the accelerated test results by Weibull distribution, elucidated accelerating factors, and estimated life time. The life is inversely proportional to 1.78-2.45 power of applied voltage, depending upon misalignment modes. The distribution of life is well expressed by Weibull distribution with shape parameter between 2.5-3.0, and proportional to the square of coefficient of variation of life. We conclude that the acceleration factors could be determined and 99.9% of tested displays will live more than 10 years. The knowledge on reliability of LCD can be now applied to new fields of LCD, such as industrial use, home appliance, and automotive instruments.     

Metal Single-Atom Cocatalyst on Carbon Nitride for the Photocatalytic Hydrogen Evolution Reaction: Effects of Metal Species

Single-atom (SA) catalysts exhibit high activity in various reactions because there are no inactive internal atoms. Accordingly, SA cocatalysts are also an active research fields regarding photocatalytic hydrogen (H₂) evolution which can be generated by abundant water and sunlight. Herein, it is investigated whether 10 transition metal elements can work as an SA on graphitic carbon nitride (g-C₃N₄; i.e., gCN), a promising visible-light-driven photocatalyst. A method is established to prepare SA-loaded gCN at high loadings (weight of ≈3 wt.% for Cu, Ni, Pd, Pt, Rh, and Ru) by modulating the photoreduction power. Regarding Au and Ag, SAs are formed with difficulty without aggregation because of the low binding energy between gCN and the SA. An evaluation of the photocatalytic H₂-evolution activity of the prepared metal SA-loaded gCN reveals that Pd, Pt, and Rh SA-loaded gCN exhibits relatively high H₂-evolution efficiency per SA. Transient absorption spectroscopy and electrochemical measurements reveal the following: i) Pd SA-loaded gCN exhibits a particularly suitable electronic structure for proton adsorption and ii) therefore they exhibit the highest H₂-evolution efficiency per SA than other metal SA-loaded gCN. Finally, the 8.6 times higher H₂-evolution rate per active site of Pd SA is achieved than that of Pd-nanoparticles cocatalyst.     

Programmed High‐Hole‐Mobility Supramolecular Polymers from Disk‐Shaped Molecules

In this paper a simple, casting solution technique for the preparation of two‐dimensional (2D) arrays of very‐high molecular weight (MW) 1D‐Pc supramolecular inorganic polymers is described. The soluble fluoroaluminium tetra‐tert‐butylphthalocyanine (ttbPcAlF) is synthesized and characterized, which can be self‐assembled to form 2D arrays of very‐high‐MW 1D‐Pc supramolecular inorganic polymers. High‐resolution transmission electron microscopy (HRTEM) demonstrates that the 1D‐ttbPcAlF, having a cofacial ring spacing of ～0.36 nm and an interchain distance of ～1.7 nm, self‐assembles into 2D‐nanosheets (～140 nm in length, ～20 nm in width, and equivalent to MW of 3.2 × 10⁵ g mol^?1). The film cast from a 1,2‐dichloroethane (DCE) solution shows a minimum hole‐mobility of ～0.3 cm² V^?1 s^?1 at room temperature by flash‐photolysis time‐resolved microwave conductivity (TRMC) measurements and a fairly high dark dc‐conductivity of ～1 × 10^?3 S cm^?1.     

Photorefractive device using self-assembled monolayer coated indium-tin-oxide electrodes

Photorefractive (PR) performances of methyl-substituted poly(triarylamine) (PTAA)-based PR device were demonstrated using chemically modified electrodes (CMEs) of self-assembled monolayer (SAM) coated indium-tin-oxide (ITO) electrodes. The SAM-ITO electrodes successfully suppressed dark current which blocks the formation of space-charge field and also causes the dielectric breakdown. The PR device consisted of composite of PTAA, 4-azacycloheptylbenzylidenemalononitrile (7-DCST), N-ethylcarbazole (ECz), and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) sandwiched between the SAM-ITO electrodes. The PR devices showed the PR performances: optical gain Γ, refractive index Δn, diffraction efficiency η, response time τ, sensitivity S, phase shift Φ, trap-limited field E_q, number density of traps N_T, and space-charge field E_SC. The remarkable response time of 11.3 ms was achieved at the low electric field of 20 V μm⁻¹, which was comparable to the response time of high-definition television (HDTV) quality of 16 ms. Our approach will widen the usage of higher mobility materials to photorefractive field and give us more favorable materials to achieve the best performance of photorefractivity in the future.     

用微机图象法对脉冲MAG焊接熔池进行观察和控制的研究

本文对微机图象法在脉冲MAG焊接中的应用作了探讨,设计和采用了带有CCD摄象机的微机控制系统,对脉冲MAG焊接熔池进行了观察、监控和图象处理。其结果证明了采用微机图象法来实现实时控制是可行的。     

Characterization of signals and noise rejection with bipolarlongitudinal intrafascicular electrodes

Longitudinal intrafascicular electrodes (LIFEs) are fine electrodes threaded into the extracellular space between axons in peripheral nerves or spinal roots. The authors are developing these electrodes for application in functional electrical stimulation and in basic physiology. An area of concern in chronic recording application of LIFEs is the possibility of electromyogram and other external noise sources masking the recorded neural signals. The authors characterized neural signals recorded by LIFEs and confirmed by three independent methods that increasing interelectrode spacing for bipolar LIFEs increases signal amplitude. The spectrum of neural signal from bipolar and monopolar LIFE lies between 300 Hz and 10 kHz. The amplitude of the spectrum increases with increasing interelectrode spacing, although the distribution is not affected. Single unit analysis of LIFE recordings show that they record selectively from units closest to the electrode active site. Units with conduction velocities ranging from 50-120 m/s were identified. Extraneural noise, as stimulus artifact or electromyogram, is much reduced with bipolar LIFE recording, as compared to monopolar recordings. Relative improvement in neural signal to extraneural noise increases with interelectrode spacing up to about 2 mm. Since there is no further improvement beyond 2 mm, the authors conclude that the preferred interelectrode spacing for bipolar LIFEs is 2 mm     

Interactive multimedia communication systems for next-generationeducation using asymmetrical satellite and terrestrial networks

We propose a new concept of a hierarchical network structure for remote education. This system combines broadband satellite networks and simple terrestrial communication networks effectively to meet the demands of point-to-multipoint communications. Remote education experiments have been conducted using the proposed satellite communication networks. The results of network characteristics and degree of satisfaction are discussed. Acceptable communication quality was achieved ensuring an interactive lecture environment