Study on high performance ice slurry formed by cooling emulsion in ice storage (discussion on adaptability of emulsion to thermal storage material)

This study focuses on an emulsion as a new thermal storage material for ice storage. Two types of emulsions were formed using an oil–water mixture with a small amount of additive. A silicone, light and lump oils were used. The water contents of the emulsions were 70, 80 and 90%. The additive was an amino group modified silicone oil. No depression of freezing point was observed for the emulsions because of their hydrophobic properties. In order to determine the structure of the emulsions, their electrical resistances were measured. Moreover, components of the liquids separating from the emulsions were analyzed. The results indicated that one emulsion was a W/O type emulsion, while the other was an O/W type. Finally, adaptability of the two emulsions to ice storage was discussed, it was concluded that a high performance ice slurry could be formed by the W/O type emulsion.     

Crystal orientation changes of Ag thin films on the Si(111) substrate due to tribo-assisted recrystallization

Crystal orientation changes of Ag thin films due to the tribo-assisted recrystallization have been studied using grazing incidence X-ray diffraction with synchrotron radiation. After preparation of an Si(111) √3 × √3-Ag surface, a 5-nm-thick Ag film was deposited on the surface at the substrate temperature of 303 K in an ultra-high vacuum chamber. The friction experiments were carried out using a diamond pin-on-plate type tribometer just after the Ag deposition in the same UHV chamber. We found that the coefficient of friction of the Ag films on the Si(111) √3 × √3-Ag surface decreases from 0.07 to 0.03, with increasing reciprocal sliding cycles. In synchronization with the coefficient change, Ag{100} grains are gradually disappearing. As a result, the Ag{111} grains cover the entire surface after 50 sliding cycles. Moreover, we found that the domain size of the Ag{111} grains increases with increasing reciprocal sliding cycles by measuring the rocking curve width. These results directly show that the Ag(111) plane is the sliding plane of friction and the coefficient of friction of Ag films is determined by the fraction of the Ag(111) grains in the Ag films. Moreover, to clarify the reaction between the Ag film and the Si substrate due to the tribo-assisted recrystallization, the substrate strain has been studied by an extremely asymmetric X-ray diffraction technique using synchrotron radiation.     

Enhanced dielectric properties of bismuth titanate/silver composites

Bismuth titanate (BiT) based composites containing silver particles are fabricated by a solution chemical process. Incorporation of silver particles does not result in unwanted reaction phase. SEM micrographs reveal fine silver particles distribute at BiT grain boundaries and into larger BiT plate-like grains. With the addition of silver, the dielectric constant increases up to ∼10 times higher than that of pure BiT ceramic, which can be attributed to the effective electric fields developed around the dispersed metal particles and the percolation effect. Additionally, the dielectric losses are significantly reduced by incorporating silver particles, and the values of BiT/Ag composites are lower than 0.5%. The dielectric properties of BiT/Ag composites are nearly frequency independent in the measured frequency range (1 kHz to 1 MHz).     

Effect of gravity on InGaSb crystal growth

The effect of gravity on dissolution of GaSb in InSb melt and growth of InGaSb was experimentally investigated. Experiments were carried out in a GaSb(seed)/InSb/GaSb(feed) sandwich system under an imposed temperature gradient. In the experiments, the GaSb feed crystal dissolved into the InSb melt to supply the required GaSb component for the growth of In_0.1Ga_0.9Sb crystal. Two parameters were considered: (1) the inclination angle (θ) of the sample for gravity as 0° and 53°, and (2) the sample diameter (D) as 9 mm and 5mm. When θ was 0°, the interface was almost flat, indicating that convection was axisymmetric and stable. Whereas the interface was distorted towards gravitational direction when θ was 53°, indicating that solutal convection was dominant. The decrease of growth temperature and sample diameter reduced the distortion of interface and the dissolution amount of GaSb feed. The homogeneous crystals were grown at the initial growth stage by supplying the GaSb component during growth.     

Sensor Fusion System Using Recurrent Fuzzy Inference

In robotic and manufacturing systems, it is difficult to measure the state of systems accurately because of many uncertain factors and noise, and it is very important to estimate the state of systems. We must measure the phenomena of systems by multiple sensors and estimate the state of systems by acquiring information of sensors. However, we can not acquire all of sensor information synchronically, because each sensor has particular sensor information and measuring time. For estimating the state of systems by multiple sensors, a multi-sensor fusion system fusing various sensory information is needed. In this paper, we propose a Recurrent Fuzzy Inference (RFI) with recurrent inputs and apply it to a multi-sensor fusion system for estimating the state of systems. The membership functions of RFI are expressed by Radial Basis Function (RBF) with insensitive ranges. The shape of the membership functions can be adjusted by a learning algorithm. The learning algorithm is based on the steepest descent method and incremental learning which can add new fuzzy rules. The effectiveness of the multi-sensor fusion system using RFI will be shown through a numerical experiment of moving robot and estimation of surface roughness in grinding process.     

Change of fuel-to-cladding gap width with the burn-up in FBR MOX fuel irradiated to high burn-up

In order to study the dependence of the gap width change on the burn-up, the fuel-to-cladding gap widths were investigated by ceramography in a large number of FBR MOX fuel pins irradiated to high burn-up. The dependence of gap widths on the burn-up was closely connected with the formations of JOG (joint oxyde-gaine) and rim structure. The gap widths decreased gradually due to the fuel swelling until ∼30 GWd/t, but beyond this burn-up the dependence showed two different tendencies. With the increase of burn-up, the gap widths decreased due to the increase of fuel swelling in the low fuel temperature region where the rim structure was observed, but they increased in the high fuel temperature region where the JOG rich in Cs and Mo formed in the gap.     

Te concentration dependent photoemission and inverse-photoemission study of FeSe1?xTex

We have characterized the electronic structure of FeSe_1−xTe_x for various x values using soft x-ray photoemission spectroscopy (SXPES), high-resolution photoemission spectroscopy (HRPES) and inverse photoemission spectroscopy (IPES). The SXPES valence band spectral shape shows that the 2 eV feature in FeSe, which was ascribed to the lower Hubbard band in previous theoretical studies, becomes less prominent with increasing x. HRPES exhibits systematic x dependence of the structure near the Fermi level (E_F): its splitting near E_F and filling of the pseudogap in FeSe. IPES shows two features, near E_F and approximately 6 eV above E_F; the former may be related to the Fe 3d states hybridized with chalcogenide p states, while the latter may consist of plane-wave-like and Se d components. In the incident electron energy dependence of IPES, the density of states near E_F for FeSe and FeTe has the Fano lineshape characteristic of resonant behavior. These compounds exhibit different resonance profiles, which may reflect the differences in their electronic structures. By combining the PES and IPES data the on-site Coulomb energy was estimated at 3.5 eV for FeSe.