Characterization and evaluating the mechanical performance of halloysite nanotubes reinforced acrylonitrile butadiene styrene/polycarbonate composites exposed to aggressive environmental conditions

Developing light weight polymer based composites dispersed with novel reinforcements which can function well in the presence of aggressive environments is an active research field in the materials engineering. Hence, in the current work, halloysite nanotubes (1 %, 2 %, 4 %, 6 %, 8 % and 10 % by weight) were reinforced into acrylonitrile butadiene styrene/polycarbonate blend and the role of reinforcing phases on the mechanical performance under aggressive environmental conditions has been evaluated. Hardness was measured as gradually increased in the composites with the increased content of the reinforcements. Impact strength of the composites was observed as increased in the composites up to 4 % reinforcement and further decreased. Increased strength was measured for the composite up to 2 % reinforcement. Ductility of the composites was decreased as reflected form the decreased % of elongation with the higher fraction of reinforcements due to induced brittleness. The composites were exposed to diluted sulfuric acid for 3 h and 6 h at 60 °C and then subjected to tensile loading. With the increased time of exposure, composites with 1 % and 2 % reinforcement exhibited relatively better performance.     

Evaluation of a multimode fiber optic low coherence interferometer for path length resolved Doppler measurements of diffuse light

The performance of a graded index multimode fiber optic low coherence Mach-Zehnder interferometer with phase modulation is analyzed. Investigated aspects were its ability to measure path length distributions and to perform path length resolved Doppler measurements of multiple scattered photons in a turbid suspension of particles undergoing Brownian and translational motion. The path length resolution of this instrument is compared with a system using single mode fibers for illumination and detection. The optical path lengths are determined from the zero order moment of the phase modulation peak in the power spectrum. The weighted first moment, which is equal to the average Doppler shift, shows a linear response for different mean flow velocities within the physiological range.     

The h-p version of the finite element method

The paper is the second in the series of two analyzing the h-p version of the finite element method. It generalizes the results of the first part (Guo, Babuska 1986) and presents computational results.Supported by the NSF Grant DMS-8315216Partially supported by ONR Contract N00014-85-K-0169     

Comparison of dicarboxylic acids as complexing agents for abrasive-free chemical mechanical planarization of copper

Abrasive particles used in chemical mechanical planarization (CMP) of copper often agglomerate and cause scratches on the finished surface. Abrasive-free CMP offers a feasible solution to this problem, and our present work examines four dicarboxylic acids (oxalic, malonic, succinic and glutaric, with increasing carbon chain lengths) as possible complexing agents for such a chemically dominated CMP process. At pH 3.0-4.0, oxalic and malonic acids are most effective for abrasive-free Cu removal. The rates of Cu dissolution and polish (with or without abrasives) are correlated with pH dependent distributions of mono-anionic (for oxalic and malonic) and neutral (for succinic and glutaric) acid species. The surface morphologies of a Cu wafers obtained by abrasive-free CMP in these acids also are more defect free and flat compared to those obtained using abrasives.     

CoopMAC: A Cooperative MAC for Wireless LANs

Due to the broadcast nature of wireless signals, a wireless transmission intended for a particular destination station can be overheard by other neighboring stations. A focus of recent research activities in cooperative communications is to achieve spatial diversity gains by requiring these neighboring stations to retransmit the overheard information to the final destination. In this paper we demonstrate that such cooperation among stations in a wireless LAN (WLAN) can achieve both higher throughput and lower interference. We present the design for a medium access control protocol called CoopMAC, in which high data rate stations assist low data rate stations in their transmission by forwarding their traffic. In our proposed protocol, using the overheard transmissions, each low data rate node maintains a table, called a CoopTable, of potential helper nodes that can assist in its transmissions. During transmission, each low data rate node selects either direct transmission or transmission through a helper node in order to minimize the total transmission time. Using analysis, simulation and testbed experimentation, we quantify the increase in the total network throughput, and the reduction in delay, if such cooperative transmissions are utilized. The CoopMAC protocol is simple and backward compatible with the legacy 802.11 system. In this paper, we also demonstrate a reduction in the signal-to-interference ratio in a dense deployment of 802.11 access points, which in some cases is a more important consequence of cooperation     

Tunnel Oxide Growth on Silicon With “Wet Nitrous Oxide” Process for Improved Performance Characteristics

In this letter, the authors present the process, growth kinetics, and electrical characteristics of tunnel oxides grown by furnace oxidation of silicon at 800 degC in an ambient of nitrous oxide (N₂O) and water vapor. Tunnel oxides of thickness 82-92 Aring are grown by this "wet N₂O oxidation" process, and the electrical characteristics such as the capacitance-voltage, current-voltage, voltage ramp, time-dependent dielectric breakdown, and charge to breakdown are evaluated using MOS capacitor as the diagnostic device. The results obtained clearly demonstrate superior performance characteristics of this oxide for Flash memory applications, with excellent charge to breakdown and minimum change in the gate voltage during constant current stressing     

Performance analysis of nonorthogonal multiple access‐based underlay cognitive relay network

This paper considers cooperative non‐orthogonal multiple access (NOMA) scheme in an underlay cognitive radio (CR) network. A single‐cell downlink cooperative NOMA system has been considered for the secondary network, consisting of a base station (BS) and two secondary users, ie, a far user and a near user. The BS employs NOMA signaling to send messages for the two secondary users where the near user is enabled to act as a half‐duplex decode‐and‐forward (DF) relay for the far user. We derive exact expressions for the outage probability experienced by both the users and the outage probability of the secondary system assuming the links to experience independent, nonidentically distributed Rayleigh fading. Further, we analyze the ergodic rates of both the users and the ergodic sum rate of the secondary network. The maximum transmit power constraint of the secondary nodes and the tolerable interference power constraint at the primary receiver are considered for the analysis. Further, the interference caused by the primary transmitter (PT) on the secondary network is also considered for the analysis. The performance of the proposed CR NOMA network has been observed to be significantly better than a CR network that uses conventional orthogonal multiple access (OMA) scheme. The analytical results are validated by extensive simulation studies.     

RETRACTED ARTICLE: An Energy Efficient Framework for Densely Distributed WSNs IoT Devices Based on Tree Based Robust Cluster Head

With the development of the internet of things, which is widely applied not only to everyday objects but also to industrial areas, the production of big data is accelerating. To provide intelligent services without human intervention in the internet of things environment, intelligent communication between objects becomes the key, and since the failure of the mechanical equipment attached to the sensor causes malfunction of the object and product failure, big data analysis to predict equipment failure is becoming more important. The purpose of this study is to propose a model for predicting mechanical equipment failure from various sense data collected in the manufacturing process. This study constructed a RHadoop-based big data platform to distribute a large amount of datasets for research, and performed logistic regression modeling to predict the main variables causing the failure from various collected variables. As a result of the study, the main variables in the manufacturing process that cause equipment failure were derived from the collected sense data, and the fitness and performance evaluation for the prediction model were made using the ROC curve. As a result of the performance evaluation of the prediction model, the ROC curve showed a fairly high prediction accuracy with AUC close to 1. The results of this study are expected to be applicable to the prediction of malfunctions, product failure, or abnormal communication between objects due to miscellaneous product faults in our daily lives in the internet of things environment.