Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

Adaptive antenna system design for multi-element combining with transient interrupted channels

This paper presents an analysis and design procedure for a buoyant cable array antenna used for satellite communications. The towed multi-element array is susceptible to washovers and fluctuations due to the ocean wave interaction with the floating hose where the elements are housed. A model of system performance for coherent multi-element combining is presented based on the dropouts and fades of the individual elements. The array design, including the number and spacing of elements, is shown to be highly dependent on the individual element exposure characteristics and the degree of correlation of the fades between channels. The joint statistics of the array are analyzed using a binary conditional element exposure model and a first-order Markov interelement correlation model. Using this analysis, a family of array designs meeting the communications requirements is produced.     

A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

Fuzzy rule-based classification of remotely sensed imagery

The purpose of this paper is to investigate the applicability of fuzzy rule-based modeling to classify a LANDSAT TM scene from 1984 of an area located in the south of Germany. Both a land cover map with four different categories and an image depicting the degree of ambiguity of the classification for each pixel is the expected output. The fuzzy classification algorithm will use a rule system derived from a training set using simulated annealing as an optimization algorithm. The results are then validated and compared with a common classification method in order to judge the effectiveness of the proposed technique. It will also be shown that the proposed method with only nine rules for four different land cover classes performs slightly better than the maximum likelihood classifier (MLC). For error assessment, the traditional error matrix and fuzzy operators have been used     

Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

Self-monitoring and intake interviewers' therapeutic orientations.

A therapist's theoretical orientation is likely to influence every facet of the therapeutic process. We explore the relationship of therapeutic orientation and self-monitoring style. To test the hypothesis that high self-monitors would be more eclectic than low self-monitors, we surveyed 30 intake therapists at a child guidance center. Results supported the hypothesis; those frequently using more than one orientation had higher self-monitoring scores. Furthermore, self-monitoring correlated negatively with psychoanalytic endorsement, but in a positive direction with behavioral, systems and eclectic endorsements. Results are discussed in terms of training needs of those differing in self-monitoring style. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Current-mode A/D converter

The authors report the design of a new current-mode A/D converter, based on a modified successive-approximations model, in 1.2 μm CMOS technology. The proposed circuit is characterised by good accuracy and fast dynamic performance, low power consumption and small occupation area. SPICE simulations allow the design approach to be validated and the electrical performance of the ADC to be predicted     

Filter matrix estimation in automated DNA sequencing

In four-color fluorescence-based automated DNA sequencing, a 4×4 filter matrix parameterizes the relationship between the dye-intensity signals of interest and the data collected by an optical imaging system. The filter matrix is important because the estimated DNA sequence is based on the dye intensities that can only be recovered via inversion of the matrix. Here, the authors present a calibration method for the estimation of the columns of this matrix, using data generated through a special experiment in which DNA samples are labeled with only one fluorescent dye at a time. Simulations and applications of the method to real data are provided, with promising results     

Analysis of the deformation of polypropylene hot-tool butt welds

Thin microtomed samples from hot-tool butt welds of polypropylene pipes are subjected to uniaxial tensile stress using a specially built instrumented microtesting machine. The deformation of the interface between the weld and the bulk polymer is measured by an optical method. An analysis of these measurements is carried out using the finite element method, and contours of the effective stress are obtained. There is a steep stress gradient at the junction of the weld flash and the bulk polymer, although the stress concentration factor is relatively low. The stress is essentially constant in the bulk polymer apart from the region near the weld zone. Tests on samples without the weld flash show that the maximum stress occurs within the weld zone. This is consistent with long-term tests on larger samples, where the fracture is found to initiate within the weld. The method of analysis enables the stress-strain response of the weld material to be determined.