A simplified dispersion limit formula for IM/DD systems and itscomparison with experimental results

A simplified formula for the dispersion limit of single-mode-fiber intensity modulation/direct detection (IM/DD) systems is derived for arbitrary given normalized pulse width U, eye opening penalty X and source linewidth enhancement factor α. From the comparison with published theoretical analyses, computer simulation and experimental data, its validity and the limits of existing formulae are shown. Using this simple and general formula, one can easily obtain the dispersion limit of various fiber types under different working conditions in IM/DD systems     

从光合作用的倒掉说起

席殊书屋、第三级书局走了,风入松、纸老虎世纪城店关了,我没太在意。2010年10月底,有着36家连锁店的光合作用竟然也宣告倒闭了!我终于淡定不起来了。清华大学出版社零售产品经理王川（简称川）清华大学出版社图书编辑刘青（简称刘）记者Justdo（简称J）新华书店＋网购是必然趋势J：光合作用倒闭了,你们惊讶吗？刘：其实我挺惊讶,因为我常去,特别是五道口那家店,从刚开业起就经常去逛。     

北运河运河核心区地表水资源状况分析

通过分析运河核心区汇水关系和北关分洪枢纽的历史变迁,收集整理1981-2018年北运河北关闸和通惠河高碑店站水文资料,计算控制流域的降水量、不同时段来水量、河道生态需水量和下游用水量以及可利用来水量,分析表明:运河核心区地表水资源较充沛,来水量较为稳定,可利用水资源保证程度较高.研究结果对于该区域科学取用水、水资源可持续利用以及相关产业的有效实践有参考意义.     

Incorporating Actor-Critic in Monte Carlo tree search for symbolic regression

Neural Computing and Applications - Most traditional genetic programming methods that handle symbolic regression are random algorithms without memory and direction. They repeatedly search for the...     

基于单片机的分段线性插值算法实现

分段线性插值算法是一种技术比较成熟、实现比较简单的低次多项式插值算法,其曲线逼近程度即插值函数与原函数误差基本满足一般的工业控制场合需要。该算法占用系统资源少,在数据采集和数据处理等工业控制领域,往往使用单片机或嵌入式系统等资源受限处理器,通过分段线性插值算法简化原函数,减少计算量,对于提高系统整体性能具有显著的现实意义。     

Effect of nitrogen and nickel on the stability of an Fe-12Cr-23Mn austenitic steel

The effect of nitrogen and nickel on the austenite stability and the structural changes as a result of cold work of an Fe-12Cr-23Mn alloy steel has been examined by transmission electron microscopy and X-ray analysis. Prestrain was performed either at room temperature or at 200° C. Final strain was carried out at liquid nitrogen temperature. The volume fraction of strain-induced martensite decreased by 40% and 12% due to the addition of 2.43% Ni and 0.11% N, respectively, despite whether prestrain was performed or not. The mechanisms are discussed in terms of the phase, stacking faults, dislocation cells and dislocation tangles induced by prestrain and final strain.     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .