辊式拉拔模用于连续拉拔机组的新技术

针对进口连续拉拔机组，独创设计了可配套使用的二连式辊模，并首次很好地解决了惯用模在辊模后的安装问题，是一种很有前途的新技术。     

用轴向气胎式离合器,制动器改造旧飞剪

采用轴向式气胎离合、制动器，改造了旧飞剪，解决了原剪机电磁离合、制动器控制不准确的问题；该剪机改造后在成品轧机后使用，剪切用１２０ｍｍ×１２０ｍｍ坯生产的大规格产品（１８ｍｍ以上），增产、增效，年总经济效益为９７．８万元     

运用NOAA AVHRR和Landsat TM数据估算多年水稻种植面积

介绍了综合运用NOAA AVHRR和Landsat TM数据进行多年水稻种植面积监测的一种方法,以湖北省为例,首先运用Landsat TM数据计算了该省1992年的水稻种植面积;接着运用1992年和1994年的NOAA AVHRR数据分别计算这两年的水稻像元数,以这两年水稻像元数的变化来反映水稻种植面积的变化;最后运用线性模型,估算1994年的水稻种植面积。所得的1994年水稻种植面积与湖北省农调队资料相比精度为84.5%。运用同样的方法估算1995年该省的水稻种植面积,精度达90%以上。     

铌酸锂γ射线辐照色心缺陷的研究

对铌酸锂晶体进行γ射线辐照处理，吸收光谱显示基础吸收边紫移，４８０ｎｍ波长附近出现一明显吸收峰，这是由空位色心Ｖ０和Ｎｂ＾４＋缺陷引起的，Ｎｂ＾４＋的存在进一步被ＥＰＲ实验所证实。本文对上述辐照缺陷的产生机理进行了讨论。     

LDD方法在提高电路工作电压中的应用研究

研究了利用轻掺杂漏结构来制作高电源电压器件的工艺方法。分析了ＬＤＤ结构参数对器件击穿特性的影响，并结合实验结果对Ｎ＾－区的注入剂量，长度及引入的串联电阻进行了优化设计。     

Automatic fault detection, isolation, and recovery in transparentall-optical networks

Network fault identification is an important network management function, which is closely related to fault management and has an impact on other network management functions such as configuration management, and performance management. This paper investigates fault surveillance and fault identification mechanisms for a transparent optical network in which data travels optically from the source node to the destination node without going through any optical-to-electrical (O/E) or electrical-to-optical (E/O) conversion. Mechanisms and algorithms are proposed to detect and isolate faults such as fiber cuts, laser, receiver, or router failures. These mechanisms allow nonintrusive device monitoring without requiring any prior knowledge of the actual protocols being used in the data transmission     

Modulation and Equalisation Considerations for High Performance Radio LANs

The European Telecommunications Standards Institute (ETSI) has recently defined a European standard for a high performance radio LAN (known as HIPERLAN). To operate as wired LAN replacements, these systems will operate at 5.2 GHz and support instantaneous bit rates of just under 24 Mb/s. To counteract the time dispersive nature of the indoor radio channel, the use of adaptive equalisation is suggested. In this paper a number of possible modulation and equalisation techniques are presented and, in particular, the Bit Error Rate (BER) performance of quasi-coherent GMSK combined with Decision Feedback Equalisation is explored through computer simulation. The trade off between symbol spaced and fractionally spaced equalisation is considered together with the importance of feedfoward and feedback synchronisation to the channel's power delay profile. The paper also includes a comparison of the RLS and LMS based training algorithms and compares the modem developed under the ESPRIT III LAURA project with that specified in HIPERLAN.The application of dual antenna diversity is investigated and its impact on the number of received error free data packets obtained as a function of signal leval and rms delay spread. The use of such diversity is shown to greatly improve the BER performance of a HIPERLAN modem. The problem of frequency offset is considered and modifications are proposed to the HIPERLAN frame structure to improve the receiver's tolerance to such errors. Important practical issues such as frame and symbol synchronisation, frequency offset correction and hardware implementation are discussed from both the LAURA and HIPERLAN viewpoint.     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。     

Economic cost modeling of environmental-stress-screening andburn-in

The electronics industry is highly competitive. The introduction of new advanced integrated circuits continues. The manufacturer must develop a product with adequate life cycle, high quality and low failure rate in the specified time period. Environmental stress screening (ESS) is widely used in the electronics industry to assist in eliminating early or patent failures. The bathtub curve is a common model for the failure rate of a population. The classic bathtub curve has three parts: infant mortality; useful life; and wearout. However, some electronic products have latent defects which are not detected by conventional inspection or functional testing, and occur during the product useful life. Most electronic systems have finite useful life. As a result, technology obsolescence is of concern and should be considered, This paper uses a new interpretation and development of the bathtub curve that integrates: (1) latent failures; and (2) the concept of obsolescence, by constructing an integrated cost model used to determine both optimal burn-in and ESS times in the same environment