Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

Nickel and chromium cycles: Stocks and flows project part IV

Nickel and chromium are essential ingredients in alloys increasingly important for energy-efficient, environmentally friendly modern technology. Quantitative assessment of the flows of these metals through the world economy from resource extraction to final disposal informs resource policy, energy planning, environmental science, and waste management. This article summarizes the worldwide technological cycles of nickel and chromium in 2000. Stainless steel is the major use of these metals, but they serve numerous other special needs, as in superalloys for high-temperature service, as plating materials, and in coinage. Because they are used primarily in alloys, novel recycling issues arise as their use becomes more widespread. “... the great New York and St. Louis double track, nickel plated railroad...” — Norwalk, Ohio, Chronicle 10 March 1881 announces arrival of surveyors for the future Nickel Plate Railway “Later [1911] I formed an alloy of Iron and Chromium, which showed remarkable resistance to rust and tarnish ... [It was] rediscovered by an Englishman named Brearley, in 1914.” —Elwood Haynes to Stephen F. Roberts, 17 January 1925     

Influence of the silicon surface treatment by plasma etching and scratching on the nucleation of diamond grown in HFCVD - a comparative study

A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with 1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers. Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332 cm⁻¹ and a peak at ∼1,580 cm⁻¹ for both samples.     

Geotechnical properties of the soft soil in Guangzhou College City

The paper describes some geotechnical properties of the soft soils in Guangzhou College City, China, which are difficult to both sample and test. Laboratory and in situ tests were carried out to assess the physical and mechanical indices of the soils. The data were statistically analyzed and linear regression undertaken such that equations could be developed by which the geotechnical properties of the soft soils can be predicted. The statistical validity of the degree of correlation confirmed that using these equations, the mechanical indices can be estimated from physical indices determined by routine testing.      

Equilibrium and crystallographic measurements of the binary tetrahydrofuran and helium clathrate hydrates

Clathrate compounds are crystalline materials formed by a physical interaction between host and relatively light guest molecules. Various types of nano-sized cages surrounded by host frameworks exist in the highly unique crystalline structures and free guest molecules are entrapped in an open host-guest network. Recently, we reported two peculiar phenomena, swapping and tuning, naturally occurring in the hydrate cages. Helium, one of the smallest light guest molecules, must be the challengeable material in the sense of physics and moreover possesses versatile applications in the field of superconductivity technology and thermonuclear industry. In this regard, we attempted for the first time to synthesize helium hydrates at moderate temperature and pressure conditions. According to inclusion phenomena, helium itself normally cannot form clathrate hydrates due to being too small molecularly without the help of hydrate former molecules (sI, sII, and sH formers). In this study, the hydrate equilibria of the binary clathrate hydrate containing tetrahydrofuran, helium, and water were determined at 2, 3, 5.56 THF mol%. Direct volumetric measurements were also carried out to confirm the exact amount of helium captured in the hydrate cages. Finally, the crystalline structure of the formed mixed hydrates was identified by powder X-ray diffraction, resulting in structure II.