关于粒子加速器人身辐射安全联锁系统设计原则的建议

本文讨论了在粒子加速器上的联锁系统设计中应遵循的一些原则,其中建立隔离区、“失效导致安全(Fail-safe)”,使用“硬件”、“多重联锁”、设置急停开关等是最重要的。     

A network management architecture for robust packet routing in meshoptical access networks

We describe an architecture for an optical local area network (LAN) or metropolitan area network (MAN) access. The architecture allows for bandwidth sharing within a wavelength and is robust to both link and node failures. The architecture can be utilized with an arbitrary, link-redundant mesh network (node-redundancy is necessary only to handle all node failures), and assumes neither the use of a star topology nor the ability to embed such a topology within the physical mesh. Reservation of, bandwidth is performed in a centralized fashion at a (replicated) head end node, simplifying the implementation of complex sharing policies relative to implementation on a distributed set of routers. Unlike a router, however, the head end does not take any action on individual packets and, in particular, does not buffer packets. The architecture thus avoids the difficulties of processing packets in the optical domain while allowing for packetized shared access of wavelengths. We describe the route construction scheme and prove its ability to recover from single link and single node failures, outline a flexible medium access protocol and discuss the implications for implementing specific policies, and propose a simple implementation of the recovery protocol in terms of state machines for per-link devices     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

Host/guest complex of Me-β-CD/2,2-dimethoxy-2-phenyl acetophenone for initiation of aqueous photopolymerization: Kinetics and mechanism

Methylated-β-cyclodextrin (Me-β-CD) was used to complex the photoinitiator, 2,2-dimethoxy-2-phenyl acetophenone (DMPA), yielding a water-soluble host/guest complex. The comparative studies demonstrated that the Me-β-CD complexed DMPA exhibited a high photoreactivity identical to the uncomplexed DMPA, while the CD complex obviously influenced the products of primary photolysis of DMPA and the photopolymerization kinetics due to the steric effect of CD on the subsequent initiation reactions. The photopolymerization rate of acrylamide can be described by the equation: R_p=K[2a]^0.62[M]^1.37[I]^0.5[Me-β-CD]⁰. The mechanism of polymerization was also discussed.