关于粒子加速器人身辐射安全联锁系统设计原则的建议

本文讨论了在粒子加速器上的联锁系统设计中应遵循的一些原则,其中建立隔离区、“失效导致安全(Fail-safe)”,使用“硬件”、“多重联锁”、设置急停开关等是最重要的。     

Seasat over-land scatterometer data. I. Global overview of theKu-band backscatterer coefficients

Statistics on the backscatter coefficient σ⁰ from the Ku-band Seasat-A Satellite Scatterometer (SASS) collected over the world's land surfaces are presented. This spaceborne scatterometer provided data on σ⁰ between latitude 80° S and 80° N at incidence angles up to 70°. The global statistics of vertical (V) and horizontal (H) polarization backscatter coefficients for 10° bands in latitude are presented for incidence angles between 20° and 70° and compared with the Skylab and ground spectrometer results. Global images of the time-averaged V polarization σ⁰ at a 45° incidence angle and its dependence on the incidence angle are presented and compared to a generalized map of the terrain type. Global images of the differences between the V an H polarization backscatter coefficients are presented and discussed. The most inhomogeneous region, which contains the deserts of North Africa and the Arabian Peninsula, is studied in greater detail and compared with the terrain type     

一种基于策略的网络管理结构方案

介绍了基于策略的网络管理的概念和当前的研究状况，在策略定义、冲突检测和系统安全问题等方面进行了讨论，提出了一种适合基于策略的网络管理的结构方案，并分析了该方案的合理性。     

A Built-in Self-Test Scheme with Diagnostics Support for Embedded SRAM

In this paper we propose a novel built-in self-test (BIST) design for embedded SRAM cores. Our contribution includes a compact and efficient BIST circuit with diagnosis support and an automatic diagnostic system. The diagnosis module of our BIST circuit can capture the error syndromes as well as fault locations for the purposes of repair and fault/failure analysis. In addition, our design provides programmability for custom March algorithms with lower hardware cost. The combination of the on-line programming mode and diagnostic system dramatically reduces the effort in design debugging and yield enhancement. We have designed and implemented test chips with our BIST design. Experimental results show that the area overhead of the proposed BIST design is only 2.4% for a 128 KB SRAM, and 0.65% for a 2 MB one.     

The near-zone field characteristics of an E-polarization plane wavepenetrating through cylindrical multiple apertures (non) coated withlossy and lossless media

The direct integral equation is formulated for describing the current on the multiple perfectly conducting strips in cylindrical geometries for an E-polarization plane wave of normal incidence. By using the Galerkin's method, the surface currents on the conducting strips are expanded in the form of a series of Chebyshev polynomials of the first kind, while the unknown expanding coefficients are solved by a set of matrix equations of finite order with a fast convergence rate and a high accuracy. Furthermore, numerical results are presented to demonstrate the variation of the penetrated near-zone field in the presence of one, two, three, four and six cylindrical apertures, and the hybrid effects of both aperture number and aperture angular widths on the penetrated fields are investigated in detail     

栲胶法变换气脱硫工艺

介绍了栲胶法脱硫的原理，工艺流程及规整填料在脱硫塔中的应用。     

纳米α-FeOOH颗粒的形态和结构

以硫酸法钛白的副产物绿矾为原料，采用滴加法制备纳米铁黄（α－FeOOH）颗粒。研究了反应体系的pH值、反应温度、通氧速率、搅拌速率和添加剂等对铁黄颗粒形态结构的影响，采用XRD、TEM等分析手段对颗粒进行表征。结果表明，调节体系pH值能控制铁黄晶型结构和色相；改变通氧速率、搅拌速率、添加剂种类以及反应温度等可以调节纳米α－FeOOH的大小和分散性。     

Containerless solidification of highly undercooled mullite melts: Crystal growth behavior and microstructure formation

A mullite (3Al₂O₃·2SiO₂) sample has been levitated and undercooled in an aero-acoustic levitator, so as to investigate the solidification behavior in a containerless condition. Crystal-growth velocities are measured as a function of melt undercoolings, which increase slowly with melt undercoolings up to 380 K and then increase quickly when undercoolings exceed 400 K. In order to elucidate the crystal growth and solidification behavior, the relationship of melt viscosities as a function of melt undercoolings is established on the basis of the fact that molten mullite melts are fragile, from which the atomic diffusivity is calculated via the Einstein-Stokes equation. The interface kinetics is analyzed when considering atomic diffusivities. The crystal-growth velocity vs melt undercooling is calculated based on the classical rate theory. Interestingly, two different microstructures are observed; one exhibits a straight, faceted rod without any branching with melt undercoolings up to 400 K, and the other is a feathery faceted dendrite when undercoolings exceed 400 K. The formation of these morphologies is discussed, taking into account the contributions of constitutional and kinetic undercoolings at different bulk undercoolings.     

Interfacial segregation of Ti in the brazing of diamond grits onto a steel substrate using a Cu-Sn-Ti brazing alloy

Diamond grits were brazed onto a steel substrate using a prealloyed Cu-10Sn-15Ti (wt pct) brazing alloy at 925 °C and 1050 °C. Due to the relatively high concentration of Ti in the brazing alloy, the braze matrix exhibited a composite structure, composed of β-(Cu,Sn), a Cu-based solid solution, and various intermetallic compounds with different morphologies. The reaction of Ti with diamond yielded a continuous TiC layer on the surfaces of the diamond grits. On top of the TiC growth front, an intermetallic compound, composed of Sn and Ti, nucleated and grew into a randomly interwoven fine lacey structure. An interfacial structure developed as the interwoven fine lacey phase was semicoherently bonded to the TiC layer, with the Cu-based braze matrix filling its interstices. The thickness of such a composite layer was increased linearly with the square root of isothermal holding time at 925 °C, complying with the law of a diffusion-controlled process. However, at 1050 °C, the segregation behavior of Ti and Sn to the interfaces between the TiC layer and the braze matrix diminished, due to the increased solubility of Ti in the Cu-based liquid phase. The enhanced dissolution of Ti in the Cu-based liquid phase at 1050 °C also caused the precipitation of rod-like CuTi with an average diameter of about 0.2 μm during cooling. SnTi₃ was the predominant intermetallic compound and existed in three different forms in the braze matrix. It existed as interconnected grains of large size which either floated to the surface of the braze matrix or grew into faceted grains. It also exhibited a nail-like structure with a mean diameter of about 1 μm for the rod section and a lamellar structure arising from a eutectic reaction during cooling.