The Solutions for Adjustment and Reconstruction of Water-Drive Surface Systems in the Old Areas of Daqing Oilfield

Introduction 　　Owing to long-time running, more facilities including stations, pipelines, vessels have become corrosive and aged ,some process has grown old, it has exert more burden for the maintenance and repair.Simultaneously, the fluid production rate, oil production rate and water injection rate has changed greatly so that the inflicts and problems from the established surface systems will become more obvious. Energy cost of production and running has increasing continuously. Capacity has been unbalance in systems and areas. 　　……     

Energy use in controlled temperature marine aquaculture

Temperature control offers benefits in land‐based marine aquaculture: stock growth rates may be enhanced by heating in winter; mortality rates in summer may be reduced by cooling. However, if the plant is not well designed, temperature control may create very large energy demands. This paper describes the application of temperature control in abalone aquaculture in New Zealand, with a focus on energy considerations in plant design. An abalone farm using a semi‐closed water conditioning system is used as a case study for which an energy model, based on a heat pump system, is developed. The model is used to determine the impact of plant design and tank conditions on the economics of the operation. Copyright © 2002 John Wiley & Sons, Ltd.     

关于粒子加速器人身辐射安全联锁系统设计原则的建议

本文讨论了在粒子加速器上的联锁系统设计中应遵循的一些原则,其中建立隔离区、“失效导致安全(Fail-safe)”,使用“硬件”、“多重联锁”、设置急停开关等是最重要的。     

A random switching method for HPWM full-bridge inverter

To overcome the problem of unequal switching loss in power switches, in conventional hybrid pulse width modulation (HPWM) full-bridge inverters, a random switching method for HPWM full-bridge inverters is proposed. The proposed method equalizes switching losses of the four switches, while also providing good output performance     

A network management architecture for robust packet routing in meshoptical access networks

We describe an architecture for an optical local area network (LAN) or metropolitan area network (MAN) access. The architecture allows for bandwidth sharing within a wavelength and is robust to both link and node failures. The architecture can be utilized with an arbitrary, link-redundant mesh network (node-redundancy is necessary only to handle all node failures), and assumes neither the use of a star topology nor the ability to embed such a topology within the physical mesh. Reservation of, bandwidth is performed in a centralized fashion at a (replicated) head end node, simplifying the implementation of complex sharing policies relative to implementation on a distributed set of routers. Unlike a router, however, the head end does not take any action on individual packets and, in particular, does not buffer packets. The architecture thus avoids the difficulties of processing packets in the optical domain while allowing for packetized shared access of wavelengths. We describe the route construction scheme and prove its ability to recover from single link and single node failures, outline a flexible medium access protocol and discuss the implications for implementing specific policies, and propose a simple implementation of the recovery protocol in terms of state machines for per-link devices     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.