Hf-doped and NH/sub 3/-nitrided high-K gate dielectric thin film with least drain current degradation and flatband voltage shift

A novel technique to form high-K dielectric of HfSiON by doping base oxide with Hf and nitridation with NH/sub 3/, sequentially, is proposed. The HfSiON gate dielectric demonstrates excellent device performances such as only 10% degradation of saturation drain current and almost 45 times of magnitude reduction in gate leakage compared with conventional SiO/sub 2/ gate at the approximately same equivalent oxide thickness. Additionally, negligible flatband voltage shift is achieved with this technique. Time-dependent dielectric breakdown tests indicate that the lifetime of HfSiON is longer than 10 years at V/sub dd/=2 V.     

基于子波变换的涡街流量传感器信号分析

长期以来 ,如何提取潜在噪声下的涡街流量信号一直是个问题。流体流速脉动 ,局部阻力 ,随机振动———所有这些因素都给解决这一问题带来难度。文章应用子波变换消噪理论 ,从软件滤波的角度分析了强噪声干扰下的涡街流量信号 ,并提出了单支重构计数方法。分析结果表明 ,这种方法对低流速流量计量效果很好 ,能够有效地扩展量程下限     

Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

羧酸系列集油剂的水面集油性能

研究了十二烷酸、十四烷酸、十六烷酸和十八烷酸在淡水中的集油能力。结果表明，这4种羧酸在淡水表面的表面膜压随其分子中碳数的增加而增大。其中后两者的表面膜压高达45～50mN／m，显著高于各类油膜膜压，满足集油剂对表面活性物质膜压的要求。4种脂肪羧酸在淡水中使柴油油膜的收缩率在1min时达到最大值，分别为80．0％、81．8％、83．8％和88．2％。它们的己醇、正庚醇、正辛醇、仲辛醇溶液的集油持续性，总体上随羧酸分子碳数增加而增大。其中十六烷酸和十八烷酸集油能力非常接近，它们的正庚醇、正辛醇和仲辛醇溶液使柴油膜面积收缩率在120h后仍保持在66．0％～70．2％。该类集油剂毒性低，易为生物降解，有实际应用前景。     

Clinical study in epidural injection with lappaconitine compound for post-operative analgesia

In this study, the effect and side-effect of epidural injection with lappaconitine compound for post-operative analgesia was observed. One hundred and twenty patients were randomly divided into 4 groups. Lappaconitine compound (LB) consisted of 12 mg of lappaconitine and 22.5 mg of bupivacaine, was given to group A (the group of observation), and lappaconitine 12 mg, bupivacaine 22.5 mg and morphine 2 mg to group B, C and D respectively for control. All were given by epidural injection with single blind method during post-operative pain of incision operation. Result showed that the initiating of analgesia was quicker in group A and C than that in group B and D, and the efficacy was group D > A > C > B. There was significant difference between group A and B in the above two parameters, P < 0.01 and P < 0.05. The analgisia maintenence time of single injection was D > A > B > C, that of group D was significantly longer than that of group A (P < 0.01). It indicated that the epidural injection with LB was more rapid and potent than that with lappaconitine alone in post-operative analgesia, and the former had no side-effect, it was safer than morphine.     

离子注入中污染的产生及防护

本文概述了离子注入过程中污染产生的原因和防止污染的措施，特别强调了对微粒污染和金属污染的防护以满足ＵＬＳＩ加工对离子注入的要求。     

Improved Yen-Joye's authenticated multiple-key agreement protocol

An authenticated multiple-key agreement protocol is proposed. The protocol is not only secure against the unknown-key attack but also more efficient than other protocols.     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

Coplanar waveguide-fed uniplanar bow-tie antenna

The design of coplanar waveguide (CPW)-fed bow-tie antenna for the 2.4-GHz ISM band is described. A coplanar waveguide-to-coplanar strips (CPW-to-CPS) balun is used to obtain the balanced feed line for the printed bow-tie. An analysis method based on the mixed potential integral equation method is used to characterize the input characteristics of the bow-tie antenna. The numerical results obtained are in good agreement with the experimental data. Through experiments with bow-tie antennas of various extended angles, the bow-tie antenna with a 90° extended angle exhibits the widest bandwidth in the desired frequency band which has a bandwidth of 17% for a VSWR <1.5:1