施工过程中腐蚀隐患的控制

通过分析石化装置施工过程中常见的现象,分析产生由这些现象加重腐蚀的原因和机理, 指出应加强施工过程中的控制,而达到预期的防腐蚀效果,消除腐蚀隐患。     

茂金属线型低密度聚乙烯的加工性能

采用齐聚-共聚复合催化剂合成出了相对分子质量分布指数大于4的原位共聚线型低密度茂金属聚乙烯(mLLDPE)。流变实验结果表明,mLLDPE具有切敏性和非温敏性。改性实验结果表明,向100质量份mLLDPE中加入5质量份氟母粒,或10质量份LDPE,或2质量份氟母粒和5质量份LDPE,可使mLLDPE的加工流动性能获得改善,聚合物的机械性能不会发生明显降低,可用常规加工设备加工。加工成型实验结果表明,使用65型管材挤出机和TDL-12L中空成型机,以氟母粒-LDPE复合改性mLLDPE为原料,可生产出内、外表面均光滑的32管材和10L中空容器,挤出过程稳定。     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

Co-digestion of manure and biowaste according to the EC animal by-products regulation and Finnish national regulations.

The objective of this study was to compare methane production and characteristics of digested material in anaerobic digestion concepts according to the Animal By-Products Regulation (ABP-Regulation) of the EC (hygienisation of biowaste for 1 hour at 70 degrees C, particle size < 12 mm) and Finnish national regulations (treatment temperature 55 degrees C, feeding interval 24 h, hydraulic retention time (HRT) 20 d, particle size < 40 mm) and with small variations in treatment methods for treating manure and biowaste. Moreover, the survival of three different salmonella bacteria in these processes was studied. Hygienisation of biowaste prior to digestion at 35 degrees C enhanced methane production by 14-18% compared to similar treatment without hygienisation. The differences in treatment temperature, HRT and hygienisation of biowaste prior to digestion did not significantly affect the characteristics of digested material. The concepts according to the ABP-Regulation and Finnish national regulations were effective in destroying salmonella bacteria to an undetectable level.     

科技进步五十年

通过回顾企业五十年的发展历程,阐述了科学技术在企业发展中发挥的重要作用.充分体现了科学技术是第一生产力.     

基于"层"模式的双机容错系统

容错技术广泛应用于各个行业来保证系统的冗余和可靠性。文章在分析比较当前的双机容错系统的性能优缺点后,提出了一种全新的基于“层”模式的双机容错系统解决方案。按照这种模式,可以从链路层到应用层构建一个通用的系统级的双机容错系统。文章对其实现的关键技术进行了阐述。     

Iterative detection/decoding for two-track partial response channels

In this letter, we investigate the iterative detection/decoding algorithms for two-track partial response channels. We first describe the iterative algorithm as an iterative message-passing/processing algorithm over a high-level normal graph and then propose two trellis-based detection algorithms. The natural one is based on a joint trellis, which can be implemented for low-order channels. For moderate-order channels, we propose a separated detection, which is based on two single-track trellises. Compared with the joint detection, the separated detection is simpler in most cases. Simulation results show that, for two-track EPR4 channels with minor intertrack interferences, the separated detection causes only marginal degradation in performance.     

Pilot Plant Study of Simultaneous Sewage Sludge Digestion and Metal Leaching

This research is related to a preindustrial pilot scale study of the performance of the simultaneous sewage sludge digestion and metal leaching (SSDML) process for decontamination and stabilization of sewage sludge. Ten batch tests were carried out in two 4?m3 bioreactors under various conditions of operation. Results indicated that the addition of 1.0 to 1.5?g?S0/L, which is the equivalent of approximately 30 to 50?kg?S0 per tons dry sludge, is sufficient to obtain conditions of acidity (pH<2.5) and oxido-reduction potential greater than 500 mV necessary for an effective solubilization of toxic metals. The final average of metal solubilization in the output sludge during the SSDML process varied in the following ranges: 25–78% Cd, 9–32% Cr, 48–100% Cu, 77–99% Mn, 15–53% Ni, 12–47% Pb, and 66–100% Zn. The N, P, and K contents were also preserved in the decontaminated sludge. Moreover, the use of low concentrations of elemental sulfur makes it possible to obtain decontaminated sludge with a low total sulfur content (1.4–1.5% S) compatible with agricultural use. The suspended solids removal calculated for the SSDML process was slightly lower, (2.5±0.4)% volatile suspended solids per day, than those reached using standard aerobic digestion. Finally, the SSDML process was found to be effective in removing bad odors and in the destruction (99–100%) of indicator bacteria.     

DSP--数字化时代的基因芯片

DSP是当今发展最为迅速的和最有发展前景的技术之一。与普通CPU和MCU相比 ,DSP在数字信号处理方面有着无可比拟的优势 ,特别适合网络、通信、控制等需要进行大量数字信号处理的应用场合。今天DSP已经成为通信、计算机、网络、工业控制以及家用电器等电子产品中不可或缺的基础器件 ,DSP在通信、计算机、网络、工业控制以及消费类电子产品等领域有着非常广泛的应用 ,本文阐述了DSP的特点、应用和市场以及DSP技术的发展前景。     

Sparse field level set method for non-convex Hamiltonians in 3D plasma etching profile simulations

Level set method [S. Osher, J. Sethian, J. Comput. Phys. 79 (1988) 12] is a highly robust and accurate computational technique for tracking moving interfaces in various application domains. It originates from the idea to view the moving front as a particular level set of a higher dimensional function, so the topological merging and breaking, sharp gradients and cusps can form naturally, and the effects of curvature can be easily incorporated. The resulting equations, describing interface surface evolution, are of Hamilton-Jacobi type and they are solved using techniques developed for hyperbolic equations. In this paper we describe an extension of the sparse field method for solving level set equations in the case of non-convex Hamiltonians, which are common in the simulations of the profile surface evolution during plasma etching and deposition processes. Sparse field method itself, developed by Whitaker [R. Whitaker, Internat. J. Comput. Vision 29 (3) (1998) 203] and broadly used in image processing community, is an alternative to the usual combination of narrow band and fast marching procedures for the computationally effective solving of level set equations. The developed procedure is applied to the simulations of 3D feature profile surface evolution during plasma etching process, that include the effects of ion enhanced chemical etching and physical sputtering, which are the primary causes of the Hamiltonian non-convexity.