Simulation and experimental investigation of solar absorption cooling system in Reunion Island

With the development of technologies and the fast increase of our population we will need to adjust the conventional electrical source to meet the continuous increasing demand. Since the energy cost as well as the environmental awareness is growing fast, technologies using renewable energies appear as an interesting alternative. The aim of this research is to present a solar-driven 30 kW LiBr/H₂O single-effect absorption cooling system which has been designed and installed at Institut Universitaire Technologique of Saint Pierre. The first part of this article deals with the simulation of the solar thermal plant. A pilot plant has been setup as part of RAFSOL which is a research program managed by the national research agency (ANR).     

A scientific application oriented classification for metal transfer modes in GMA welding

In this work, metal transfer in solid wire GMA welding was studied. Several experiments with different combinations of gas-wire-parameters were carried out to observe metal transfer and to characterize the various transfer modes. A laser shadograph system with synchronized electrical signals and high speed filming were used. New modes were observed and their particular characteristics described for completeness. A classification for metal transfer, oriented to scientific personnel (researchers, scholars and students), is proposed, in which the modes are independent of the type of shielding gas or welding power source.     

Effect of material,geometry, surface treatment and environment on the shear strength of single lap joints

The single lap joint is the most studied type of adhesive joint in the literature. However, the joint strength prediction of such joints is still a controversial issue as it involves a lot of factors that are difficult to quantify such as the overlap length, the yielding of the adherend, the plasticity of the adhesive and the bondline thickness. The most complicated case is that where the adhesive is brittle and the overlap long. In any case, there is still a problem that is even more difficult to take into account which is the durability. There is a lack of experimental data and design criteria when the joint is subjected to high, low or variable temperature and/or humidity. The objective of this work is to carry out and quantify the various variables affecting the strength of single lap joints in long term, especially the effect of the surface preparation. The Taguchi method is used to decrease the number of experimental tests. The effect of material, geometry, surface treatment and environment is studied and it is shown that the main effect is that of the overlap length.In order to quantify the influence of the adhesive (toughness and thickness), the adherend (yield strength and thickness), the overlap, the test speed, the surface preparation and durability on the lap shear strength, the experimental design technique of Taguchi was used in the present study. An experimental matrix of 18 tests was designed and each test was repeated three times. The influence of the eight previously-mentioned variables could be assessed using the statistical software Statview^®. In this paper a simple predictive equation is proposed for the design of single lap joints.     

Beneficial and technological analysis for the recycling of solar grade silicon wastes

In the current paper, different kinds of silicon wastes during the production of SoG-Si were summarized and the beneficial analyses, such as financial value, energy value, CO₂ emissions, and efficiency and energy payback time, were briefly discussed for the recycling of SoG-Si wastes. Possible technologies to recycle and purify SoG-Si wastes were reviewed: such as filtration, sedimentation, solidification control, electromagnetic separation, plasma oxidation, centrifugation, and high temperature remelting process, et al.     

Ultraviolet light effect on electrical properties of a flexible organic thin film transistor

We have fabricated pentacene-based transistors on a transparent and flexible substrate made of polyethylene-terephthalate. We have shown that using an optical excitation at a wavelength of 365 nm photoconductivity modifies the carrier density without changing the mobility. The performance of the flexible organic phototransistors is mostly due to high-photosensitivity in the off-state with a ratio of photocurrent to dark current of about 2 10⁴. Furthermore, the response times of the phototransistor are lower than 0.1 s. These results indicate that such transistors could be potentially used in photodetectors or amplifiers ordered by an optical gate. Moreover, we have noticed that there is no significant change in the mobility value when the transistor is bent in the direction of the current flow.     

Investigation of the thermal and structural properties of single-molecule magnet/polymer nanocomposite films

The inclusion of manganese-based single-molecule magnets (SMMs) into solvent cast films of poly(methyl methacrylate) (PMMA) or polycarbonate (PC) was found to influence the thermal stability of these polymers. Examination of the thermal decomposition profiles of PMMA films by thermo-gravimetric analysis (TGA) established that increasing weight % of SMM results in both enhancement of the rate of decomposition initiated at “head-to-head” linkages along with suppression of the rate of decomposition initiated at vinylidene chain ends. In the case of PC films, the temperature at which the primary thermal decomposition occurs decreases with increasing weight % of SMM. The extent of these decomposition trends is correlated to the degree of SMM dispersal, as studied by transmission electron microscopy (TEM). Favourable interactions between the ligands coordinated to the SMMs and the polymer or solvent used in film preparation dictated the degree of SMM dispersal, with the ligand–polymer interactions being dominant on the nano-length scale (1–100 nm) and ligand–solvent interactions being dominant on the micro-length scale (>100 nm).     

Production of thin calcium phosphate coatings from glass source materials

Calcium phosphate (CaP) coatings, from 40 000 to 200 000 nm thick, on titanium and titanium alloy substrates, were produced using radio frequency (RF) sputtering. Such coatings on dental implants have the potential for improving initial bone ingrowth rates. The success of these coatings may allow the movement from two stage implant systems to single stage implant systems, significantly reducing the time required for healing and fixture placement. Glass source materials were developed for the RF sputtering facility and the resultant coatings were characterized and compared to coatings sputtered from a conventional plasma sprayed hydroxyapatite (HA) source material. The coatings were characterized according to their chemistry, crystalline orientation, and residual strain.     

Technology to facilitate ethical action: a proposed design

As emerging technologies support new ways in which people relate, ethical discourse is important to help guide designers of new technologies. This article endeavors to do just that by presenting an ethical analysis and design of technology intended to gather and act upon information on behalf of its users. The article elaborates on socio-technological factors that affect the development of technology to support ethical action. Research and practice implications are outlined.     

Logic design for printability using OPC methods

The steps that create physical shape data in a typical logic device design-to-reticle flow are cell layout, place and route, tapeout, OPC or RET, data fracture, and reticle build. Here, we define OPC as the transformation of reticle data to compensate for lithographic and process distortions so that the final wafer pattern is as close to the target pattern-the designed layout-as possible. We define RETs as the general class of transformations for reticle data that aim to improve the patterning process window; therefore, OPC is a subset of RET. DFM is traditionally considered to be implemented at the cell layout or routing stages of this flow. Examples include the optimization of a layout based on critical-defect area, the addition of redundant contacts and vias, wire spreading, upsizing of metal landing pads, and the addition of dummy metal tiles to improve the planarity after chemical-mechanical planarization (CMP). We presented a detailed analysis of these techniques in an earlier work. In contrast, this article analyzes the possibility of extending these traditional methods into the OPC stage and introduces new post-tapeout RET methods for improving printability.