Optimised anaerobic treatment of house-sorted biodegradable waste and slaughterhouse waste in a high loaded half technical scale digester.

Anaerobic co-digestion of organic wastes from households, slaughterhouses and meat processing industries was optimised in a half technical scale plant. The plant was operated for 130 days using two different substrates under organic loading rates of 10 and 12 kgCOD.m(-3).d(-1). Since the substrates were rich in fat and protein components (TKN: 12 g.kg(-1) the treatment was challenging. The process was monitored on-line and in the laboratory. It was demonstrated that an intensive and stable co-digestion of partly hydrolysed organic waste and protein rich slaughterhouse waste can be achieved in the balance of inconsistent pH and buffering NH4-N. In the first experimental period the reduction of the substrate COD was almost complete in an overall stable process (COD reduction >82%). In the second period methane productivity increased, but certain intermediate products accumulated constantly. Process design options for a second digestion phase for advanced degradation were investigated. Potential causes for slow and reduced propionic and valeric acid degradation were assessed. Recommendations for full-scale process implementation can be made from the experimental results reported. The highly loaded and stable codigestion of these substrates may be a good technical and economic treatment alternative.     

溶胶--凝胶镀膜技术综述(连载5)

第三节　常见氧化物膜目前研究最多的氧化物膜可谓二氧化硅和二氧化钛膜 ,这两种薄膜也是接受呈色离子、制备彩色镀膜常用的基体膜 ,所以 ,有必要将它们单独列出 ,加以讨论。1　二氧化钛膜在所有高折射率材料中 ,由钛的化合物制备的氧化物膜具有特殊的实际意义。因此 ,对二氧化     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Management gaps analysis: a case study of groundwater resource management in New Zealand

The primary objective of this project is to identify gaps, whether real or perceived, that hinder effective groundwater management in New Zealand. These gaps show as gaps in information, gaps in implementation, gaps in technological and management tools, and gaps in understanding of fundamental processes. The secondary objective is to propose a management strategy to close the identified gaps. Several methods are used to meet these objectives: surveys distributed to selected staff in each regional council; the review of various written reports; the analysis of land-use databases; and private consultation within each regional council. Results show that groundwater management in New Zealand is generally reactionary with the main gaps being in strategic planning and national guidelines. Most gaps appear to be predominantly information and implementation issues. In some cases there are gaps in the understanding of fundamental processes within an aquifer system, including the long-term effects of land-use on groundwater quality. An adaptive management approach is suggested as a means of closing these gaps.     

Trajectory control of incompletely restrained parallel-wire-suspended mechanism based on inverse dynamics

This paper discusses parallel wire mechanisms where an end-effector of the mechanism is suspended by multiple wires. The mechanisms enable not only three-dimensional (3-D) positioning but also 3-D orienting of the end-effector, unlike typical wire suspension-type mechanisms such as overhead crane. To discuss the parallel-wire-suspended mechanisms generally, two forms of basic dynamic equations are presented. Then the parallel wire mechanisms are classified into two types based on the basic equations. Dynamical properties of the two types of wire-suspended positioning mechanism are discussed. In this paper, one of the wire-suspended mechanism, incompletely restrained-type parallel wire mechanism, is mainly discussed on its inverse dynamics problem and its trajectory control problem. The inverse dynamics problem for the incompletely restrained-type mechanism plays an important role on its control problem, because the mechanism has low stiffness based on incomplete constraints on the suspended object which is governed by its dynamics. The paper proposes an antisway control method for the suspended object. In the method, the inverse dynamics calculation is used for nonlinear dynamics compensation to control the suspended object of the incompletely restrained parallel wire mechanism.     

ASON实际组网中架构及演进方式分析

对在实际组网中选择合理的ASON架构和保护方式作了相应分析，并为搭建可向ASON平滑演进的传统网络时需注意的问题提供了参考意见，     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry     

Teaching robust programming

Robust programming aims to prevent abnormal termination or unexpected actions and requires code to handle bad (invalid or absurd) inputs in a way that is consistent with the developer's intent. For example, if an internal error occurs, the program might terminate gracefully rather than simply failing, providing enough information for the programmer to debug the program and avoiding giving the user additional access or information. This article focuses on teaching these principles.     

Steady-state operation of a high-voltage multiresonant converter in a high-temperature environment

Often scientific instruments on exploratory satellites are used to collect cosmic particles. These instruments, such as the Faraday cup, require a high-voltage regulated power source. On the proposed solar probe satellite there will be instruments which will collect cosmic particles close to the sun. Naturally temperature effects on the voltage regulator are a concern. Specifically power dissipation within the regulator must stay within stringent guidelines. The high-voltage regulator circuit is a resonant flyback topology with a dissipative series switch whose on resistance controls the output voltage level. The extreme temperatures in space will change the inductance of the flyback transformer which will affect the output voltage. State space analysis techniques are used to determine how the value of the transformer inductance and capacitance in the flyback converter affects the output voltage and consequently the power dissipated by the transformer and the switch. The accuracy of the analysis is verified by comparing results with those obtained from an experimental circuit. The results can then be used to help the designer chose nominal capacitance and inductance values that will work over the temperature range of interest.