地下金属矿山斜坡道浆土路修筑工艺及应用研究

斜坡道是地下金属矿山的主要运输通道,其道路质量直接影响着矿山的安全运输和经济效益。针对斜坡道混凝土浇筑路面存在的筑路成本高、养护时间长、使用寿命短及维护困难等不足,引入浆土路修筑技术,开展了地下金属矿山斜坡道浆土路筑路材料配比试验、黏土搓条和崩解试验、水洗筛分试验,并在云南卡房分公司完成了浆土路试验路段的修筑。结果表明：浆土路筑路技术能够很好地应用于地下矿山道路修筑,具有施工工艺简单、筑路成本低、施工周期短、承载能力强、抑尘防滑和低碳环保等诸多优点,为地下金属矿山道路修筑提供了工程借鉴,对于矿山降本增效、节能减排及安全高效具有重要的意义。     

平板类气体辅助注射成型产品的CAE模拟研究

通过建立具有代表性的平板类气体辅助注射成型产品模型,借助注塑成型CAE软件Moldflow对该模型进行了一系列分析模拟。通过对模拟结果数据的综合分析和数学处理,得到了气体注射参数对气道穿透长度的影响规律、气体注射参数设置及气道穿透长度预测公式。     

低合金钢锤头的研制与应用

为提高石料破碎机锤头的使用寿命,经过多次试验摸索和现场工业性试验,成功研制出价廉物美的低合金钢锤头。结合锤头含碳量较低、合金元素少的特点,对其进行阶段式复合热处理。热处理后锤头头部工作表面硬度50~55HRC,柄部硬度33~42HRC,使用寿命为锻打钢锤头的3~4倍。     

球团链箅机回转窑工艺中氯和硫元素迁移规律

摘要：对链箅机回转窑工艺中各段球团样品进行实验分析,研究了氯元素和硫元素在链箅机回转窑工艺中的迁移规律,明晰了烟气中HCl的生成机制。结果表明,球团原料中的氯元素主要是以NaCl的形式存在,氯元素有一部分在链箅机抽风干燥段会转变成HCl气体并进入烟气,一部分在链箅机预热Ⅱ段之后以NaCl的形式汽化进入烟气,剩余的氯元素仍以NaCl的形式存在于成品球团矿中。烟气中的HCl气体是在抽风干燥段,由富含SO2的烟气与含水球团料层中的NaCl发生反应生成的,烟气中SO2转变成Na2SO4重新固定于料层中。在预热Ⅰ段和预热Ⅱ段,烟气中的SO2与原料中碳酸钙分解生成的游离CaO反应生成CaSO4,也会重新固定烟气中的SO2。     

Dependence of dielectric properties on BT particle size in EP/BT composites

The polymer-ceramic composites of epoxy resin (EP) and barium titanate (BT) were prepared.BT powders of different BT particle sizes from 100 nm to 1 μm were used in the preparation.The dielectric properties, such as dielectric constant, dielectric loss and electrical breakdown strength, of the EP/BT composites were studied.The morphology of the composites was characterized by the means of scanning electron microscopy (SEM).The results show that the dielectric constant of the composites is much higher than the epoxy matrix at frequency range from 1 kHz to 10 MHz, and it is also obviously dependent on the size of BT particles.The electrical breakdown strength of the composites decreases with the increase of the BT content.The dependence of electrical breakdown strength on BT particle sizes was also discussed.     

Preparation of alumina-doped yttria-stabilized zirconia nanopowders by microwave-assisted peroxyl-complex coprecipitation

Alumina-doped yttria-stabilized zirconia （ADYSZ） nanopowders were prepared by microwave-assisted peroxyl-complex coprecipitation （MAPCC） using ZrOCl2-8H2O, Y2O3 and AICly6H2O as starting materials, NH2-H2O as precipitant and H2O2 as complexant. The effects of adding H2O2 and microwave drying on the preparation and properties of ADYSZ were investigated. The precursors and nanopowders were studied by EDX, XRD, SEM and TEM techniques. The results show that the uniformity of component distribution within ADYSZ nanopowders is improved by adding appropriate dosage of H2O2. Complexing reaction between H2O2 and Zr^4＋ ion restrains the hydrolyzation and precipitation of Zr^4＋ ion. With the addition of H2O2, Al^3＋, y^3＋ and Zr^4＋ ions can be precipitated synchronously in a relatively narrow range of pH value. H2O2 also improves the filterability of the wet precipitate. The highly hydrophilic precipitates can be quickly and effectively separated from aqueous solution. During microwave drying process, the moisture of wet precursors is selectively heated. Quick expansion of steam vapor within the wet colloidal particles causes the aggregations burst into numerous tiny lumps. Compared with oven drying, microwave drying can not only shorten drying time but also reduce aggregation intensity of the resultant ADYSZ nanopowders.     

Cu-Fe-Cr原位复合材料中的纤维相

通过感应熔炼、铸造、锻造和冷拔变形制备了Cu-16Fe-2Cr(质量分数,％)原位复合材料,最终线材(其轧制后的冷拔变形量达到η=ln(A_0/A)=5.42,A_0和A分别为冷拔起始和冷拔后线材的横截面面积)的抗拉强度为980 MPa。将Cu基体选择腐蚀后提取出纤维,采用SEM和TEM观察分析纤维相组织形态。在较低的应变量时,一些Fe—Cr纤维保持着与铸态树枝晶相同的bcc单晶结构,选区电子衍射表明纤维已经形成了〈110〉织构。在较高的应变量时,单根Fe-Cr纤维分为一些由晶界隔开的平行亚单元(宽度约为100 nm),通过亚单元共同的[110]衍射获得了晶粒之间的相对取向关系,相邻晶粒的偏差角在11°—82°之间。根据Hall-Petch关系讨论了原位复合材料的强度问题。     

超宽板坯连铸机黏结漏钢原因及预防措施

分析了安钢第二炼轧厂超宽板坯连铸机黏结漏钢的原因,并采取了针对性的预防措施,黏结漏钢率大大降低.     

Borides at interfacial zone of IC6 TLP bonded joints

1　INTRODUCTIONTransientliquidphase (TLP)bondingtechniquehasbeensuccessfullyusedinjoiningheatresistantal loys ,likeHastelloyX ,Inconel713C ,In10 0 ,Udimet5 0 0 ,70 0 ,MarM 2 0 0 ,0 0 7,2 4 7,30 2 ,Rene′80 ,TD NiCr ,MA75 4,6 0 0 0 ,PWA14 2 2 ,CSMX 2etc ,whicharesusceptibletohotcrackingor post weldheat treatmentcrackingproblemsduringfusionweld ing[14 ] .Inaddition ,therewerereportsofjoiningNiAlandTiAlintermetallicsbyTLPbondingmethod[510 ] .Forexample ,Galehadinvestigatedthemic…