重油纳米化助燃效果研究与表征

将复配的分散剂加入重油中制备得到重油纳米颗粒，采用氧弹热值对比法对所研制的纳米化重油进行实验室评价。研究结果表明，纳米化后的重油燃烧性能得到了改善，在掺水量为3％～12％时，重油的燃烧效率提高了2．5％～6．1％。通过TEM观察，纳米化后的重油呈水包油（O／W）型乳液结构，油水界面清晰，界面膜较厚，乳化油粒径约为20～50nm，油水分散均匀，并且分散后的重油粘度增幅小，掺水量在15％以内，粘度增幅不超过20％，并且随着掺水量的增加，乳化重油的粘度逐渐减少。另外，乳化重油稳定性好，室温下至少可保存6个月，在80℃下存放3天未发生破乳现象。     

Measurement System of Uniformity between Breech Horizontal Platform and Datum Tube Axis of Rocket Artillery

The purpose of this development is to detect the parallelism between the breech horizontal platform and the datum tube axis of the rocket artillery. The located aiming mechanism at the muzzle and located adjustment mechanism at the breech are designed in the system. Besides those, the system also uses an autocollimator with accuracy of 1″ and a collimating mirror together to determine the axis of the datum tube. An electronic level with accuracy of 2″ is employed to measure and display the value of the included angle and the parameter of the inclined direction. The entire accuracy of this system is σ≤± 9.1″. This paper describes the composition and the operating principle of the system and analyzes the accuracy. The development of this system supplies reliable measurement method for new rocket artilleries and artilleries, and this technology is of a good application prospect.     

我国企业开展流程再造应从工作研究开始

由于管理基础工作薄弱，我国很多企业流程再造的努力未获成功。基于企业流程再造与工作研究之间的对比分析，文章提出了运用工作研究领域内的有关理论、经验、方法和工具来帮助我国企业开展流程再造。     

非化学计量LaNi5型储氢合金的性能

采用富La混合稀土与Ni、Co、Mg等元素组合，获得了一种非化学计量LaNi5型储氢合金、用金相、XRD和SEM-EDX等方法分析了该合金的组织结构，研究了合金的气相储氢特性以及电化学性能，结果表明：在1.6MPa氢压和温度29℃下，该合金的储氢量达到1.58%（质量分数），该合金的放电容量为380mAh/g。经300次循环后容量保持率为55%，该合金的基体是CaCu5型结构的LaNi5相，但有第二相（LaMg)Ni3析出，这种第二相的形成是导致该合金大容量的关键。     

平纹织物复合材料的弹性模量预测

利用细观力学的代表体积元(RVE)法,预测了平纹织物复合材料的弹性模量。建立了表征RVE形态的数学模型,分析了细观结构与宏观性能之间的关系,编制了从组分材料的弹性性能推测复合材料的弹性性能的预测程序。对理论预测进行了实验验证,理论值与实测值在一定误差范围内能较好吻合,说明此预测方法具有一定的可靠性。     

In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.     

应用底饲回燃循环流化床技术改造东锅DG35/3.82-7型流化床锅炉

采用飞灰循环底饲回燃技术改造西南合成制药总厂热电分厂、天府矿务局磨心坡发电厂2台东方DG35/3.82-7型低倍率循环流化床锅炉。改造后运行结果表明,锅炉可长期、稳定运行,尾部飞灰可燃物含量大幅度降低,锅炉蒸发量提高20％左右,节煤效果明显。为燃用贫煤、无烟煤和煤矸石等劣质燃料且锅炉炉膛高度较低的电站技改,提供了一种切实可行的方法。     

新生牛肝活性肽的制备及其毒性检测

目的制备新生牛肝活性肽并评价其安全性。方法采用膜法分离制备新生牛肝活性肽。将3批制品于37～40℃,75%相对湿度条件下存放3个月,以多肽含量为指标观察其稳定性,并进行急性毒性试验、小鼠骨髓细胞微核试验、Ames试验、小鼠精子畸形试验和大鼠喂养试验。结果制备的3批新生牛肝活性肽存放3个月后,多肽含量无明显下降,质量稳定。小鼠和大鼠经口灌人大于20.0g/kg体重的新生牛肝活性肽,均无急性毒性。3种致突变试验均未显示出致突变性,大鼠喂养试验各项指标均未见明显毒性。结论新生牛肝活性肽未表现出明显毒性。     

高温用（SiC—AlN）Mo功能梯度材料的加工

讨论了热屏蔽用（SiC－AIN）／Mo功能梯度材料的粉末冶金加工。利用钼作为基体材料，以承担结构强度和连接可能性。根据在1000K温差内的完全热传递，研究了组分配置的设计，并且以最佳的组分配置成功地加工出了（SiC－AIN）／Mo功能梯度材料的烧结坯料。     

运用韦柏函数分析发动机燃烧过程时若干问题的探讨

探讨了韦柏函数的内涵及其在实际应用中的若干问题；应用双韦柏函数对涡流室式柴油机的燃烧过程进行分析，加深了对分隔室式发动机燃烧过程的认识．