Structural material from waste plastic

In efforts to contribute to community development, particularly in the context of Egyptian communities, waste plastics materials were successfully recycled without the difficult task of separation and reused to economically produce new structural material. Recycling was performed by mixing molten waste plastics with sand to produce these new materials. Samples with different percentages of plastics and different particle sizes of sand were used in the process. Materials showed acceptable density and high compressive strength, which was shown to be at a maximum with contents of about 30–40% waste plastic. Furthermore, certain types of sand having different colors were used to produce attractive materials, suitable for decorative uses. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2543–2547, 2004     

Dynamic mechanical properties of agricultural residues‐filled polystyrene

Agricultural residues (cotton straw) were added as very small particles to polystyrene (PS) at different weight ratios by using a melt‐mixing technique. The dynamic mechanical tests were performed over a wide range of temperatures and frequencies by using an ARES rheometer (Rheometrics Scientific) operated in the dynamic mode. The dynamic mechanical properties in terms of the storage modulus (G′), loss modulus (G″), compliance moduli, loss tangent, and dynamic viscosity were studied and compared for PS and PS composite. The results showed that the dynamic mechanical moduli and viscosity were found to increase with the addition of cotton straw and rise further with its loading increasing. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 37–40, 2004     

Rheological and dielectrical characterization of melt mixed polycarbonate-multiwalled carbon nanotube composites

A series of composites of polycarbonate (PC) with 23 different contents of multiwalled carbon nanotubes (MWNT) was produced by melt mixing using the masterbatch dilution method. In dielectric measurements, AC conductivity and complex permittivity data obtained in the frequency range between 10⁻³ and 10⁷ Hz at room temperature indicated the electrical percolation threshold at about 1.0 wt%.

The dynamic mode melt rheological measurements for the same samples at eight temperatures between 170 and 280 °C showed a visible change in the frequency dependence of dynamic moduli and the absolute value of the complex viscosity |η*| particularly at low frequencies. In literature these changes are sometimes related to so called ‘percolation threshold concentration’. Applying this picture to our experimental data we have to assume that the percolation threshold is strongly dependent on the measurement temperature. It changes from about 5 to 0.5 wt% MWNT by increasing the measurement temperature from 170 to 280 °C, respectively. This temperature dependence cannot be explained by a classical liquid-solid transition but may be related to the existence of a combined nanotube-polymer network.     

Yield response of lentil to directly applied and residual phosphorus in a Mediterranean environment

The response of lentil grown under rainfed conditions to directly applied and residual phosphorus (P) was described by a modified Mitscherlich equation, accounting for the effects of rainfall on (1) potential yield, and (2) the availability of soil-P to the crop. The response of lentil yield to directly applied and residual P was studied in two-course cereal–lentil rotational trials under rainfed conditions in a Mediterranean-type environment. Cereal crops were grown at different P application rates during 4 growing seasons at 3 sites, representing different rainfall zones in northwest Syria. Lentil (Lens culinaris Med.) was grown during 4 seasons at the same sites, each lentil crop following a cereal crop. In 3 out of 4 lentil-growing seasons, additional P was applied to lentil in subplots to compare the residual and direct effects of P application. The initial contents of extractable soil-P (P-Olsen) were low at all sites, in the range of 2–5 ppm P. Under the conditions of the experiments, lentil appeared to benefit slightly more from P applied to the preceding wheat crop (residual P) than from directly applied P. It is shown that the modified Mitscherlich equation could be used as a basis for P fertilizer recommendations for rainfed farming. As for lentil, it was concluded that a single application of P to the wheat crop in a wheat/lentil rotation could reduce the cost of lentil production, without reducing lentil yield.     

Effect of solvents on radiation‐induced grafting of styrene onto fluorinated polymer films

The effect of solvents on radiation‐induced grafting of styrene onto commercial fluorinated polymer films such as poly(tetrafluoroethylene) (PTFE), poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) and poly(tetrafluoroethylene‐co‐perfluorovinyl ether) (PFA) was investigated by a simultaneous irradiation technique. Three solvents, ie methanol, benzene and dichloromethane, were used to dilute styrene under various irradiation doses, dose rates and monomer concentrations. The effect of addition of mineral and organic acids on the degree of grafting in the presence of the three solvents was also studied. The degree of grafting was found to be strongly dependent upon the type of solvent and composition of the monomer/solvent mixture. Dilution of styrene with dichloromethane in various grafting conditions was found to enhance dramatically the degree of grafting compared with other solvents, and the maximum degree of grafting was achieved at a monomer/solvent mixture having a composition of 60:40 (v/v). The formation of polystyrene grafts in the three fluorinated films was verified using FTIR spectrometry. © 2001 Society of Chemical Industry     

Synthesis and Characterization of Cationic Surfactants Based on N‐Hexamethylenetetramine as Active Microfouling Agents

Four cationic surfactants of quaternary hexammonium silane chloride based on hexamethylenetetramine and alkyl chloride were synthesized. The chemical structures of the prepared cationic surfactants were elucidated using Fourier transform infrared (FT‐IR) spectroscopy and mass spectrometry analysis. The surface and thermodynamic properties of the prepared surfactants were also studied. The performance of these cationic surfactants as microfouling agents against two strains of Gram‐negative bacteria, namely, Pseudomonas aeruginosa and Escherichia coli, and two strains of Gram‐positive bacteria, namely, Staphylococcus aureus and Bacillus subtilis, were evaluated as antimicrobial agents. The results showed that the maximum antimicrobial activity was detected for N‐hexamethylenetetramine‐N‐ethyl silane ammonium trichloride (Ah). The maximum and minimum antimicrobial activities were 73 and 60 % against S. aureus and E. coli, respectively, at a concentration of 5 mg/l, pH 7, and 37 °C.     

Evaluation of Some Nonionic Surfactants Derived From Vanillin as Corrosion Inhibitors for Carbon Steel During Drilling Processes

Four eco‐friendly nonionic surfactants based on vanillin were investigated as corrosion inhibitors against carbon steel dissolution during the drilling process in the oil field. The corrosion inhibition efficiencies of the tested compounds were determined using weight loss, electrochemical polarization, and electrochemical impedance techniques. The data obtained show that the nonionic surfactants prevent the corrosion of drilling tools and their inhibition efficiency increased with an increase in their concentration. Tafel curves revealed that the surfactants under study act as mixed inhibitors. The adsorption of the inhibitors on carbon steel surface decreases the double‐layer capacitance. The inhibition efficiencies of the surfactants were influenced by their chemical structure and surface activity.     

Water filtration properties of novel composite membranes combining solution electrospinning and needleless melt electrospinning methods

New composite polyvinyl alcohol (PVA)/polypropylene (PP) membranes were prepared by combining both solution electrospinning and melt electrospinning methods. Self‐designed and made needleless melt electrospinning device was used to fabricate PP membranes which acted as the support layer. PVA membrane on the surface was fabricated via solution electrospinning. The electrospun PVA/PP composite membranes were characterized by the pore size distribution, pure water flux, and rejection ratio, then compared with general composite membranes. Characterizations revealed that the fiber diameter of solution electrospun PVA membrane and melt electrospun PP membrane were 0.171 ± 0.027 and 2.24 ± 0.33 μm, respectively, and the average pore size was 0.832 μm and 27.29 μm, which was much smaller than the nonwoven membrane. The rejection ratio to the 500 nm particles of the PVA/PP composite membrane could reach more than 96%, which was much larger than that of the PVA/non‐woven substrate of 90%, and the melt electrospun PP membrane of 80%, and still maintained high permeate flux of 32,346 L/m²h under the pressure of 0.24 bar. This approach of compositing the solution electrospun membranes and melt electrospun membranes could be useful in designing novel microfiltration membrane owning both higher flux and higher rejection ratio. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41601.     

Fabricating and robust artificial neural network modeling nanoscale polyurethane fiber using electrospinning method

With regard to the fact that currently there is no comprehensive method to predict diameter of polyurethane/solvent fiber from electrospinning, in this study, diameter prediction of polyurethane/solvent fiber was conducted using neural networks and an error of 166 nm was observed. This error shows that artificial neural networks (ANNs) can predict diameter of electrospinning polyurethane fibers well. Then, considering weak repeatability nature of electrospinning in fabricating fibers with desired diameter, least mean square is used to improve stability of neural network model that shows an error of 113 nm, which represented better results compared to common ANN. To investigate the effect of each one of parameters affecting fiber diameter, sensitivity analysis was conducted. Along with this predicting model, sensitivity analysis can be used to reduce parameters space before conducting future studies. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45116.