Improved strained HEMT characteristics using double-heterojunctionIn0.65Ga0.35As/In0.52Al0.48As design

The DC and microwave properties of strained In_0.65Ga _0.35As/In₀₅₂Al_0.48As HEMTs (high electron-mobility transistors) with double-heterojunction design are presented. The high sheet carrier density and good carrier confinement give rise to excellent device performance with very low output conductance. For 1×150-μm² long-gate HEMTs, the measured cutoff frequency f_T and maximum frequency of oscillation f_max are as high as 37 and 66 GHz, respectively     

Preparation and characterization of low-halogen and nonhalgoen fire-resistant low-smoke (FRLS) cable sheathing compound from blends of functionalized polyolefins and PVC

An attempt is made to develop a novel series of cable sheathing compounds with variation in chlorine content and sufficient fire retardance and unique low-smoke characteristics. These are prepared by blending PVC and functionalized polyolefins in different compositions. PE and EPDM have been functionalized by grafting dibutyl maleate (DBM) using DCP as initiator. FRLS compounds made from PVC-functionalized polyolefin blends possess the special characteristics of low-smoke, low-acid-gas generation, increased fire retardance, and improved volume resistivity, which are much better in comparison with a typical PVC sheathing compound. Thermoplastic elastomer (TPE) based nonhalogen FRLS compounds are also reported. The mechanisms for grafting, polymer-polymer and polymer-filler interactions have been presented.     

Electrodeposited CdSe0.5Te0.5: Photoelectrochemical solar cells

CdSe_0.5Te_0.5 thin films have been prepared by electrodeposition. The films were characterized by X-ray diffraction, energy dispersive X-ray fluorescence microanalysis, scanning electron microscopy, optical absorption techniques, Auger electron analysis and electron probe microanalysis. Photoelectrochemical cell performance after electrode annealing and photoetching treatments is reported.     

Hardness and Fracture Toughness of SiC-Particle-Reinforced MoSi2 Composites

The indentation technique has been used to evaluate the hardness and fracture toughness of SiC-reinforced MoSi₂ composites made by hot-pressing. It is seen that the toughness increases with increasing indentation crack length (under increasing load) and a probable mechanism responsible for this behavior is described. It is also observed that there is an optimum volume fraction of SiC particles for which the maximum fracture toughness of the composite can be achieved.     

Studies on microbridges of superconducting YBCO thin film

Critical current densities of the superconducting Y-Ba-Cu-O (YBCO) films have been observed to decrease with the increase of power of microwave radiation. Presence of Josephson type of junctions in the microbridges has been established from the microwave irradiation and magnetic field studies. BCS energy gap parameter (2/kT _c ) has been calculated from thedI/dV characteristics and found to be 3.7 at 13 K.     

Surface modes of a sessile water drop: an optical tweezer based study

A high-precision method to study the dynamics of two-fluid interfaces using an optical tweezer and a phase-sensitive detection technique are described. The disturbances set up at the interface are studied by analyzing the motion of an optically trapped particle in the bulk of the fluid, i.e., away from the interface. The usefulness of the technique is demonstrated for the well-known problem of a horizontally vibrated sessile liquid drop. The vibrational modes of the liquid drop excited by sinusoidally vibrating the support in a horizontal plane appear as resonances in the motion of the trapped particle. The nature of the resonance is studied in detail by measuring the real part, the imaginary part, and the phase response of the motion of the particle as a function of the "effective" size of the liquid drop. Excellent quantitative agreement with the theoretically predicted values of the eigenfrequencies and damping of the surface modes is obtained.     

A 3-GHz 70-mb SRAM in 65-nm CMOS technology with integrated column-based dynamic power supply

Column-based dynamic power supply has been integrated into a high-frequency 70-Mb SRAM design that is fabricated on a high-performance 65-nm CMOS technology. The fully synchronized design achieves a 3-GHz operating frequency at 1.1-V power supply. The power supply at SRAM cell array is dynamically switched between two different voltage levels during READ and WRITE operations. Silicon measurement has proven this method to be effective in achieving both good cell READ and WRITE margins, while lowering the overall SRAM leakage power consumption.     

Multispeed tool-life tests with radioactive tools

A multispeed testing method for obtaining tool-life parameters using radioactive tools has been developed. By suitable interpolation of the instantaneous rates of absolute wear measured for a number of discrete cutting speeds, the corresponding tool-life values can be deduced in a test employing a single cutting edge. Using failure criteria based on wear-land width, crater volume and total wear volume, tool-life parameters were obtained in orthogonal cutting tests with irradiated high speed steel tools. Subsidiary experiments, including conventional tool-life testing, confirmed the validity of the multispeed method over the cutting speed range investigated.     

Failure Analysis of a Cylindrical Roller Bearing from a Rolling Mill

Premature failure of a cylindrical roller bearing of a gear box input shaft from a hot strip mill has been investigated. The pins of the cylindrical rollers of the bearing broke from the welded joints at their ends on the cage ring. Investigations were carried out on the failed roller pin and the welded joint. The investigation consists of visual observation, chemical analysis, characterization of macro- and microstructures, measurement of hardness profile, fractography, and energy dispersive spectroscopy (EDS). The fracture surface of the roller pins exhibits beach marks. Scanning electron microscopy (SEM) of the fracture surfaces reveals striations suggesting fatigue failure. The measured hardness profile along the welded joint shows very high hardness due to the presence of untempered martensite at the fusion boundary as revealed by the microstructural examination. Analyses of the results infer that the roller pins failed by the initiation of fatigue cracks from the welded joint because of the presence of untempered martensite originated due to improper welding process.     

Synthesis,characterization and application of biopolymer-ionic liquid composite membranes

Biopolymer composite membranes based on chitosan doped with an ionic liquid (IL) 1-ethyl 3-methylimidazolium thiocyanate (EMImSCN) have been developed and characterized. The doped ionic liquid films show remarkable enhancement in ionic conductivity (σ). The Fourier transform infrared (FTIR) spectroscopy, atomic force microscopy (AFM) and X-ray diffraction studies (XRD) affirmed the composite nature, good incorporation of ionic liquid and reduction in crystallinity of films, respectively. The interaction between ionic liquid, chitosan and iodide polymer electrolyte matrix was evaluated by cyclic voltammetry. The fabricated dye sensitized solar cell (DSSC) using this new biopolymer electrolyte membranes shows promising performance.