Axial developments of interfacial area and void concentration profiles in subcooled boiling flow of water

Axial developments of the local void fraction, interfacial area concentration and bubble Sauter mean diameter were measured in subcooled boiling flow of water in a vertical internally heated annulus using the double-sensor conductivity probe technique. Measurements were performed under varying conditions of heat flux, inlet liquid velocity and inlet liquid temperature. A total of 10 data sets were acquired. Based on these measurements with the previous data obtained in the present test loop, the influence of flow condition on the profiles of local two-phase flow parameters was discussed. The measured average void fraction and interfacial area concentration were compared with the predictions by existing correlations for drift-flux parameters and interfacial area concentration. Also, the recently proposed bubble layer thickness model in subcooled boiling was evaluated for the measurement data.     

振动工况下环管内气液两相流参数分布实验研究

为模拟地震对反应堆堆芯内两相流动的影响,将振动产生装置与实验段结合,并利用电导探针技术实验研究了振动工况下环管内气液两相流局部参数的分布特性。振动装置所采用的偏心轮的偏心距为15.875mm,并可通过调节电机转速获得不同的振动周期。环管实验段内径和外径分别为19.1mm和38.1mm,总长度为2.32m。实验以空气和水为工质,流动工况覆盖了泡状流、弹状流及搅混流等流型。实验结果表明,振动对管内气液两相流局部参数如含气率和界面浓度等分布具有重要影响。随振动周期的减小,管内两相流参数分布发生明显变化。另外振动对低含气率的泡状流影响较大,随含气率的增加,流型逐渐向搅混流过度,振动对两相流参数的影响逐渐减小。     

Effects of Microstructure on Superplastic Behavior and Deformation Mechanisms in β-Silicon Nitride Ceramics

The influence of grain shape and size on superplastic behavior and deformation mechanisms was investigated in annealed β-silicon nitride materials and compared with the results for hot-pressed material. The microstructure of the annealed materials consisted of fine equiaxed β-grains together with some elongated ones. Similar to the deformation behavior in the hot-pressed material, strain hardening did not occur in these annealed materials. Moreover, in contrast to the deformation behavior under tension, grain alignment under compression resulting from the development of a mild texture did not give rise to strain hardening. An annealed material with small elongated grains had a flow-stress dependency of n = 1, whereas other annealed materials with large elongated grains exhibited a flow-stress dependency of n = 1.6. In terms of texture development and the effect of grain shape on the creep rate when diffusion was the rate-controlling mechanism, a single curve with a stress exponent of ∼1 and a grain-size exponent of 3 were obtained for all materials. This suggests that the deformation mechanism in these annealed materials was the same as that of fine equiaxed β-silicon nitride.     

Lifestyle Factors Involved in the Pathogenesis of Alopecia Areata

Alopecia areata is a representative inflammatory skin disease that is associated with various environmental stimuli. While psychological stress is believed to be a major pathogenetic trigger in alopecia areata, infants and newborns also suffer from the disease, suggesting the possible presence of other environmental factors. Daily lifestyle is well known to be involved in various inflammatory diseases and influences the severity of inflammatory skin diseases. However, only a limited number of studies have summarized these influences on alopecia areata. In this review article, we summarize lifestyle factor-related influences on the pathogenesis of alopecia areata and focus on environmental factors, such as smoking, alcohol consumption, sleep, obesity, fatty acids, and gluten consumption.     

满月塔结构的设计、施工及动力特性分析

介绍了位于天津的满月塔的工程概况并提出了圆钢拉杆预应力的结构体系。用ANSYS建立了满月塔的三维有限元模型。通过静力分析设计了拉杆、梁以及柱构件。针对预应力的施加方法设计了新型的拉杆连接节点和梁贯通型梁柱节点。对满月塔进行了模态分析和地震响应分析,并通过与悬臂梁模型的对比分析了满月塔的动力特性。     

The friction behavior of Ni-, SiO2- and mica sodium silicate-based solid lubrication composites

The friction behavior of Ni⁻-, SiO⁻₂- and mica sodium silicate-based lubricant composites, which included BN, WS₂ and graphite as lubricants, were examined. A ring-on-disk apparatus, in which a solid lubricant composite disk was held against a rotating stainless ring, was used as the test configuration. The tests were run with a load from 62 to 250 N in temperatures from 20 to 800°C in the laboratory environment. The wear surface was characterized by scanning electron microscope and X-ray photo spectroscopy. The major findings were that both mica sodium silicate- and SiO⁻₂-based composites failed at above 500°C due to severe wear and surface damage; in contrast, Ni⁻-based composite showed a stable friction coefficient and low wear from 20 to 800°C.     

Superplastic Deformation in Silicon Nitride–Silicon Oxynitride In Situ Composites

Starting with a mixture of ultrafine β-Si₃N₄ and a SiO₂-containing additive, a superplastic Si₃N₄-based composite was developed, using the concept of a transient liquid phase. Significant deformation-induced phase and microstructure evolutions occurred in the nonequilibrium, fine-grained Si₃N₄ material, which led to the in situ development of a Si₃N₄–22-vol%-Si₂N₂O composite and strong texture formation. The unusual ductility of the composites with elongated Si₂N₂O grains was attributed to the fine-grained microstructure, the presence of a transient liquid phase, and the alignment of the elongated Si₂N₂O grains. The mechanical properties of the resultant composite were enhanced rather than impaired by superplastic deformation and subsequent heat treatment; the resultant composite exhibited both high strength (957 MPa) and high fracture toughness (4.8 MPa·m^1/2).     

Effect of Dynamic Microstructural Change on Deformation Behavior in Liquid-Phase-Sintered Silicon Carbide with Al2O3–Y2O3–CaO Additions

Nanocrystalline β-SiC with additions of 7 wt% Al₂O₃, 2 wt% Y₂O₃, and 1 wt% CaO was subjected to tensile deformation to study its microstructural behavior under the dynamic process. The liquid-phase-sintered body had a relative density of >97% and an average grain size of 170 nm. Tension tests were conducted at initial strain rates ranging from 2 × 10⁻⁵ to 5 × 10⁻⁴ s⁻¹, in the temperature range 1973–2023 K, in both argon and N₂ atmospheres. Although grain-boundary liquids formed by the additions vaporized concurrently with the decomposition of SiC and extensive grain growth, the maximum tensile elongation of 48% was achieved in argon. Annealing experiments under the same conditions revealed that vaporization and grain growth were both dependent on experimental time. Therefore, high strain rates suffered less from the hardening effect when cavitation damage was more severe. Testing in an N₂ atmosphere brought about crystallization of the grain-boundary phase and prevented severe vaporization; however, fracture occurred at only 8% elongation. Grain-boundary sliding was still the dominant mechanism for deformation.     

Heat-Resistant Silicon Carbide with Aluminum Nitride and Erbium Oxide

Fully dense SiC ceramics with high strength at high temperature were obtained by hot-pressing and subsequent annealing under pressure, with AlN and Er₂O₃ as sintering additives. The ceramics had a self-reinforced microstructure consisting of elongated SiC grains and a grain-boundary glassy phase. The strength of these ceramics was ∼550 MPa at 1600°C, and the fracture toughness was ∼6 MPa·m^1/2 at room temperature. The beneficial effect of the new additive composition on high-temperature strength might be attributable to the introduction of aluminum from the liquid composition into the SiC lattice, resulting in a refractive grain-boundary glassy phase.     

Amine‐functionalization of the nanotitanate ETS‐2

A series of nonporous, amine‐functionalized sodium titanates was prepared and the thermal and adsorptive behavior of the samples were characterized. Engelhard titanosilicate 2 was chosen as a substrate for its high surface area (～300 m²/g), native surface hydroxyl concentration, and lack of microporosity; eliminating the risk of fouling the adsorbent under certain process conditions. Aminosilanes containing a single (N1), two (N2), and three (N3) amine groups were chemically grafted to the surface of the substrate and the adsorption capacity for CO₂ measured through thermogravimetry‐mass spectroscopy (TG‐MS) desorption, volumetric adsorption, and gravimetric adsorption/desorption cycling. The N3 sample displayed complete monolayer coverage and was capable of adsorbing five times as much atmospheric CO₂ as the N1 sample. Testing under anhydrous conditions only engages the primary amine on the tether and the data consistently suggests a correlation between amine utilization and the proportion of monolayer coverage for these adsorbents. © 2013 American Institute of Chemical Engineers AIChE J, 59: 4727–4734, 2013