Design Methodology and Area Sensitivity Analysis of Horizontal Subsurface Flow Constructed Wetlands

An approach is presented to satisfy the demand for simple criteria, guidelines and models for the preliminary sizing of horizontal subsurface flow (SF) constructed wetland systems. This approach eliminates time-consuming calculations and iterations by providing graphical solutions for wetland system sizing. Therefore, it can be used for the preliminary assessment of new or performance evaluation of existing subsurface flow constructed wetland systems. The validity of this methodology is checked with data from existing systems and is found to be quite satisfactory. This methodology is combined with simple equations predicting the maximum wetland capacity in summer, so as to assist designers in sizing installations in tourist areas with increased summer populations. Furthermore, based on this methodology, a sensitivity analysis is performed of the area requirements for wastewaters of various strengths and various design conditions and performance criteria. The results provide a useful overview to engineers and further simplify the design methodology of new subsurface flow constructed wetland systems.     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Interaction of triton X-100 on silica: A relationship between surface characteristics and adsorption isotherms

Adsorption of Triton X-100 on various silica substrates has been investigated. A number of solids, including a natural quartz, this quartz washed with HCl acid and subsequently heated at 1273 K; two aerosils and one Kieselgel silicas were studied. These solids exhibit surface areas in the range of 5 to 430 m² g^?1. All the Triton adsorption isotherms display an S-shape at the adsorption temperatures studied (298 and 308 K). It has been found that the pretreatments of natural quartz (by water washing, impurities removed by acid and/or high temperature calcination) affect considerably the amounts of TX-100 adsorbed. Measurements of surface composition have been made by X-ray photoelectron spectroscopy (XPS) with particular emphasis on the presence of impurities and on the number of OH groups at the surface of the samples. The nature of the surface hydroxyl has also been studied by infrared spectroscopy. Furthermore, the specific number of hydroxyl groups on the surface of the silica samples has been determined by thermogravimetric analysis. Finally an attempt to correlate solid surface characteristics with adsorption isotherms has been developed.     

GaN and AlGaN high-voltage rectifiers grown by metal-organic chemical-vapor deposition

In this paper, we report the study of the electrical characteristics of GaN and AlGaN vertical p-i-n junctions and Schottky rectifiers grown on both sapphire and SiC substrates by metal-organic chemical-vapor deposition. For GaN p-i-n rectifiers grown on SiC with a relatively thin “i” region of 2 μm, a breakdown voltage over 400 V, and forward voltage as low as 4.5 V at 100 A/cm² are exhibited for a 60-μm-diameter device. A GaN Schottky diode with a 2-μm-thick undoped layer exhibits a blocking voltage in excess of ∼230 V at a reverse-leakage current density below 1 mA/cm², and a forward-voltage drop of 3.5 V at a current density of 100 A/cm². It has been found that with the same device structure and process approach, the leakage current of a device grown on a SiC substrate is much lower than a device grown on a sapphire substrate. The use of Mg ion implantation for p-guard rings as planar-edge terminations in mesageometry GaN Schottky rectifiers has also been studied.     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.     

Presupposition failure — A comedy of errors

Presuppositions of utterances are the pieces of information you convey with an utterance no matter whether your utterance is true or not. We first study presupposition in a very simple framework of updating propositional information, with examples of how presuppositions of complex propositional updates can be calculated. Next we move on to presuppositions and quantification, in the context of a dynamic version of predicate logic, suitably modified to allow for presupposition failure. In both the propositional and the quantificational case, presupposition failure can be viewed as error abortion of procedures. Thus, a dynamic assertion logic which describes the preconditions for error abortion is the suitable tool for analysing presupposition.     

A novel cyclic process using CaSO<Subscript>4</Subscript>/CaS pellets for converting sulfur dioxide to elemental sulfur without generating secondary pollutants: Part I. Feasibility and kinetics of the reduction of sulfur dioxide with calcium-sulfide pellets

Certain new sulfide-smelting processes and coal-gasification processes generate high-strength sulfur dioxide streams, for which a new process for converting sulfur dioxide to elemental sulfur needs to be developed because no process exists that is generally and economically applicable to the treatment of such streams. A thermodynamic and experimental investigation to develop a new process for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium sulfide and calcium sulfate without generating secondary pollutants was carried out. In this process, the starting raw material, calcium sulfate, is reduced by a suitable reducing agent, such as hydrogen, to produce calcium sulfide, which is used to reduce sulfur dioxide to elemental sulfur vapor and calcium sulfate. The latter is, in turn, reduced to regenerate calcium sulfide. In this Part I, detailed experimental results are presented on the kinetics of the reaction between sulfur dioxide and calcium-sulfide pellets, which produces elemental sulfur and calcium sulfate. The experiments were carried out at temperatures between 1023 and 1088 K and sulfur-dioxide partial pressures between 9 and 60 kPa by the use of a thermogravimetric analysis (TGA) technique. The rate of this reaction was demonstrated by the conversion of 40 pct calcium-sulfide pellets obtained from the hydrogen reduction of fresh calcium sulfate in 10 minutes at 1073 K under a sulfur-dioxide partial pressure of 43 kPa. The reactivity decreased somewhat during the first three cycles but remained largely unchanged thereafter up to the tenth cycle. This characteristic of the pellets is important because the solids must be reusable for repeated cycles to avoid generating secondary pollutants. A pore-blocking model was found to fit the reaction rate. The reaction is first order with respect to sulfur-dioxide partial pressure and has an activation energy of 101 to 134 kJ/mol (24 to 32 kcal/mol) for calcium-sulfide pellets reacted and regenerated several different times. Sulfur dioxide-containing streams from certain sources, such as the regenerator off-gas from an integrated-gasification, combined-cycle, desulfurization unit and new sulfide-smelting plants, contain much higher partial pressures of SO₂. In these cases, the rate of the first reaction is expected to be proportionally higher than in the test conditions reported in this article. The reduction kinetics of calcium-sulfate pellets with hydrogen gas is reported in the accompanying Part II.