Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

N.m.r. line shape-relaxation correlation analysis of bitumen and oil sands

The first results of the analysis of bitumen and oil sands using the recently developed n.m.r. spingrouping technique are presented. The n.m.r. relaxation experiments were carried out on bitumen, and on natural and dried oil sands samples. The results indicate that the spin-grouping can resolve and quantify several components of the samples studied. The bitumen and bitumen fraction of the oil sands are resolved according to their spin-spin relaxation times into three major groups: solid-like (rigid), solid-like (mobile) and semi-liquid. The water in the oil sands exists in two different environments. Tentatively one environment is assigned to be the bridges between the sand grains, while the other is assigned to be the clay surface. One can conclude that with spin grouping of complex mixtures the decomposition (in which components are resolved according to their dynamic state) is possible. The accuracy of such resolution is of the order of a few per cent.     

Biodegradable hollow microfibres to produce bioactive scaffolds

Biodegradable hollow microfibres containing particles loaded with specific active agents can be potentially employed to produce a special kind of substrate for tissue engineering, able to function as a scaffold and at the same time to act as a drug‐releasing system. Biodegradable hollow microfibres based on poly(lactic acid) were produced by a dry–wet spinning procedure. Drug‐loaded microparticles were prepared by a simple oil‐in‐water emulsion and entrapped inside the fibres. The morphology of both fibres and particles was investigated by scanning electron microscopy. The mechanical and thermal properties of the fibres were investigated by tensile tests and differential scanning calorimetry. In vitro tests were performed to evaluate the release of the drug from the fibres loaded with the particles Copyright © 2004 Society of Chemical Industry     

Retaining maximum antioxidative potency of wheat germ oil refined by molecular distillation

A process of physical refining wheat germ oil using the technique of molecular distillation (MD) is presented in this work. Wheat germ oil was obtained from the germ by solvent extraction using hexane and also by cold pressing. The oil extracted with hexane was degummed and bleached before deacidification in order to modify the parameters of phosphorus and color. The goal in carrying out the stage of physical refining by MD was to preserve the maximum amount of original antioxidative potential obtained from extraction of the crude oil. The effect of evaporation temperature of one‐stage MD on the efficiency of free fatty acid elimination was studied. The antioxidant portion was followed by means of analytic determination of tocopherols by high‐performance liquid chromatography. Tocopherol retention up to 98% was achieved in the oil extracted by pressing, and yields of up to 96% were achieved in the oil extracted with hexane. Copyright © 2007 Society of Chemical Industry     

Structural Response of Nuclear Containment Shield Buildings with Construction Openings

Steam generator replacement at nuclear power plants requires large construction openings in nuclear containment structures. This study examines the effects of such openings placed in a 61?cm (2?ft) thick dome of a shield building. The dome is cast in two layers, and the limiting cases of the two layers acting as one and the lower layer carrying the entire load are considered. Without openings, the stresses due to dead load in the structure are very low when compared to the material strength. With openings, the loads are easily redistributed around the opening, and the maximum stresses for the conservative case are between three and four and one-half times larger than in the original structure with no openings. The extent of the affected area around the holes is relatively small. Smooth corners in the openings are necessary to avoid high local stress concentrations.     

Pervasive 2007: It's about the User

Pervasive computing is as much about the user as it is about the technology. So, the Fifth International Conference on Pervasive Computing emphasized desirability rather than just feasibility. Featured themes included user benefits, human-computer interaction, group and social interactions, context awareness, finding and positioning people and objects, and personal privacy.     

Hydrodechlorination of 3-chloropyridine and chlorobenzene in methanol solution over alkali-modified zirconia-supported palladium catalysts

The liquid-phase hydrodechlorination of 3-chloropyridine and chlorobenzene has been studied over alkali-modified zirconia-supported palladium catalysts. The modification of the ZrO₂ with alkali metal carbonates improves the catalytic activity of the final palladium catalyst. Therefore, the larger the ionic radii (Li⁺ < Na⁺ < K⁺), the greater the catalytic activity (TOF) of the palladium catalyst. For 3-chloropyridine, hydrodechlorination proceeds without catalyst deactivation. This is explained as the result of the interaction of reaction products (pyridine and HCl) forming pyridinium chloride, thus avoiding the detrimental effect of HCl on the palladium particles. Catalytic hydrodechlorination of chlorobenzene over Pd catalysts exhibits an initial catalytic activity (TOF) much lower than that of 3-chloropyridine and the Pd catalysts deactivate as the reaction proceeds. Finally, chlorobenzene hydrodehalogenation has also been carried out in the presence of an equimolecular amount of pyridine resulting in a decrease in the initial reaction rate on the one hand, but also in an increase in final conversion on the other.     

Infrared and ultraviolet–visible spectroscopic studies of silica, [(Cp)2ZrCl2] and trimethylaluminum interactions

Infrared and UV–vis studies of metallocene immobilization on silica are reported here. The results have indicated changes in the Zr coordination sphere of metallocene depending on the immobilization route used. The reaction of [(Cp)₂ZrCl₂] with silica formed [(Cp)₂ZrCl]⁺[SiO]⁻ species. The same metallocene, reacting with TMA modified silica, formed monomethylated and dimethylated species by the substitution of chloro for methyl ligands, stabilized on the surface by interaction with “MAO-like” species (methylaluminoxane, MAO). These monomethylated and dimethylated cationic zirconium species are the active centers for the polymerization reaction. Different order of TMA addition in the silica modification step generated surface species of a similar nature, differing in their relative quantities. The highest amount of these active species was obtained when the support was added to the TMA solution rather than adding the TMA solution to the silica support. This was the most significant parameter affecting catalytic activity in ethylene polymerization.