Basic trends in development of drilling equipment for ore mining with block caving method

The authors have determined the causes of drop in performance of induced block caving using fans of blastholes 105 mm in diameter and single blastholes 250 mm in diameter, as well as the sources of increased drilling cost and expansion of start-up time of production blocks in Abakan underground mine. Alternatives of improvement in drilling efficiency under current conditions are discussed.     

Effects of Undercooling and Transformation Time on Microstructure and Strength of Fe–C–Mn–Si Superbainitic Steel

Strength of Materials - A metallographic method, dilatometry, and X-ray diffraction were applied to investigate the effects of undercooling and holding time on bainitic transformation,...     

In situ observation of synthesized nanoparticles in ultra-dilute aerosols via X-ray scattering

In-air epitaxy of nanostructures (Aerotaxy) has recently emerged as a viable route for fast, large-scale production. In this study, we use small-angle X-ray scattering to perform direct in-flight characterizations of the first step of this process, i.e., the engineered formation of Au and Pt aerosol nanoparticles by spark generation in a flow of N₂ gas. This represents a particular challenge for characterization because the particle density can be extremely low in controlled production. The particles produced are examined during production at operational pressures close to atmospheric conditions and exhibit a lognormal size distribution ranging from 5–100 nm. The Au and Pt particle production and detection are compared. We observe and characterize the nanoparticles at different stages of synthesis and extract the corresponding dominant physical properties, including the average particle diameter and sphericity, as influenced by particle sintering and the presence of aggregates. We observe highly sorted and sintered spherical Au nanoparticles at ultra-dilute concentrations (< 5 × 10⁵ particles/cm³) corresponding to a volume fraction below 3 × 10^–10, which is orders of magnitude below that of previously measured aerosols. We independently confirm an average particle radius of 25 nm via Guinier and Kratky plot analysis. Our study indicates that with high-intensity synchrotron beams and careful consideration of background removal, size and shape information can be obtained for extremely low particle concentrations with industrially relevant narrow size distributions.

     

Design of an Electromagnetic Frequency Tunned Antenna for Mobile Communications

Wireless Personal Communications - Current mobile communications technology relies heavily on efficient design of antennas, where the operational characteristics of the wireless communication...     

Sintering behaviour of fluorapatite–silicate composites produced from natural fluorapatite and quartz

In this work, the sintering behaviour of fluorapatite (FAp)–silicate composites prepared by mixing variable amounts of natural quartz (2.5 wt% to 20 wt%) and FAp was studied. The composites were pressureless sintered in air at temperatures from 1000 °C to 1350 °C. The effects of temperatures on the densification, phase formation, chemical bonding and Vickers hardness of the composites were evaluated. All the samples exhibited mixed phase, comprising FAp and francolite as the major constituents along with some minor phases of cristobalite, wollastonite, dicalcium silicate and/or whitlockite dependent on the quartz content and sintering temperature. The composite containing 2.5 wt% quartz exhibited the best sintering properties. The highest bulk density of 3 g/cm³ and a Vickers hardness of >4.2 GPa were obtained for the 2.5 wt% quartz–FAp composite when sintered at 1100 °C. The addition of quartz was found to alter the microstructure of the composites, where it exhibited a rod-like morphology when sintered at 1000 °C and a regular rounded grain structure when sintered at 1350 °C. A wetted grain surface was observed for composites containing high quartz content and was believed to be associated with a transient liquid phase sintering.     

The impacts of cattle access points on deposited sediment levels in headwater streams in Ireland

Cattle access to streams has been linked globally with degradation of stream water quality, driven largely by bank erosion and resultant instream, fine sediment deposition. The majority of evidence on such effects is however based in arid and semiarid regions of the United States and Australia, with few studies relating to cool temperate climates such as Northwest Europe. In this study, “Quorer” resuspendable sediment samples were taken from riffle geomorphic units upstream (control) and at two points downstream (pressure and recovery) of cattle access points in headwater streams in agricultural catchments in Ireland to assess levels of deposited stream sediment. Samples were taken in April/May (2016) prior to the grazing season and in October (2016) at the end of the grazing season. Sites in good‐high ecological status catchments and less than good ecological status catchments were included in the study. Higher levels of sediment were found downstream of cattle access points in both good‐high status and less than good status catchments; however, the impacts of access points were spatially confined to, in most cases, the area immediately downstream of the point of access. There was a strong correlation between deposited sediment mass and organic matter (OM) mass, with levels of OM increasing linearly with deposited sediment mass. Levels of measured sediment were negatively correlated with riparian habitat health (measured using a qualitative habitat assessment). The results of this study highlight the need for measures to prevent cattle access to headwater streams where access points can be many in order to manage local habitat quality and downstream water quality issues.     

An automated treatment planning strategy for highly noncoplanar radiotherapy arc trajectories

Radiation therapy is a technology-driven cancer treatment modality that has experienced significant advances over the last decades, due to multidisciplinary contributions that include engineering and computing. Recent technological developments allow the use of noncoplanar volumetric modulated arc therapy (VMAT), one of the most recent photon treatment techniques, in clinical practice. In this work, an automated noncoplanar arc trajectory optimization framework designed in two modular phases is presented. First, a noncoplanar beam angle optimization algorithm is used to obtain a set of noncoplanar irradiation directions. Then, anchored in these directions, an optimization strategy is proposed to compute an optimal arc trajectory. The computational experiments considered a pool of twelve difficult head-and-neck tumor cases. It was possible to observe that, for some of these cases, the optimized noncoplanar arc trajectories led to significant treatment planning quality improvements, when compared with coplanar VMAT treatment plans. Although these experiments were done in a research environment treatment planning software (matRad), the conclusions can be of interest for a clinical setting: automated procedures can simplify the current treatment workflow, produce high-quality treatment plans, making better use of human resources and allowing for unbiased comparisons between different treatment techniques.     

The Impact of PbF2-Based Glasses on Radiation Shielding and Mechanical Concepts: An Extensive Theoretical and Monte Carlo Simulation Study

Journal of Inorganic and Organometallic Polymers and Materials - This work aimed to investigate the impact of Lead-fluoride based glasses via theoretical and simulation techniques on mechanical and...