Measurement of zeolite,silicate, and phosphate in laundry detergent products by inductively coupled plasma atomic emission spectrometry

This paper reports the development of a method for simultaneously measuring zeolite, silicate, and phosphate in laundry detergent products by inductively coupled plasma atomic emission spectrometry. A sample is decomposed under alkaline oxidative conditions to decompose zeolite, silicate, phosphate, and organic substances. Then hydrochloric acid is added to the decomposed solution to dissolve aluminum hydroxide precipitate before analysis. This sample preparation procedure was investigated by using a total organic carbon analyzer and was confirmed to be applicable to simultaneous measurements of zeolite, silicate, and phosphate. Relative standard deviation for the analysis is less than 2.1%, recovery is more than 99.0%, and the calibration curve gives a correlation coefficient ofR=1.000. The detection limit of this method for aluminum and silicon is 0.1%, and for phosphorus, 0.2% by weight in the product. This method is applicable to various laundry detergent products that contain zeolite, silicate, or phosphate and is five times faster than the three wet chemical methods.     

LC GRIN lens mode with wide viewing angle for rotatable 2D/3D tablet

To widen the vertical and horizontal angular ranges where the lens performs well, the off‐axis performance of a liquid crystal gradient index (LC GRIN) lens is analyzed by the combined simulation system of an LC director simulator and a ray‐tracing simulator. We found that the angular difference between an LC alignment direction and an electrode array direction of the LC GRIN lens is one of significant parameters, and detailed conditions of structure are established. The measurement result shows that the developed structure reduces the degradation ratio in a luminance profile from 61% to 3.2%. We have applied a user tracking system for the rotatable 3D display, equipped with a detection of a panel orientation and a face position. As a result, we have developed a rotatable 2D/3D tablet whose 3D viewing azimuth angle is over 30° in both landscape and portrait orientations.     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

Decomposition of Carbon Dioxide to Carbon with Active Wustite at 300°C

Active wustite (FeδO, with a δ value of 0.98) was prepared by keeping normal wustite (δ value of 0.94) in a N₂ atmosphere at 300°C for 10 min. This reaction is given by (4δ₂–3)Fe_δ1O→(4δ₁–3)Fe_δ2O + (δ₂–δ₁)Fe₃O₄ where δ₁= 0.94 and δ₂= 0.98. The equation indicates that the normal wustite undergoes eutectoid decomposition into active wustite and stoichiometric magnetite (Fe₃O₄). Carbon dioxide (1.013 × 10⁵ Pa) was almost completely (100%) decomposed into carbon (zero valence) by the active wustite at the low temperature of 300°C, which was associated with the transformation of the active wustite into the stoichiometric magnetite. The internal pressure of the reaction cell eventually became a vacuum.     

Shear-rate dependence of first normal stress difference of poly(isoprene-b-styrene) in solution near the order-disorder transition temperature

Viscoelastic properties of poly(isoprene-b-styrene) in dioctylphthalate under steady shear flow were measured near the order—disorder transition temperature. In ordered states, first normal stress difference N₁ is proportional to shear rate at low region, but becomes proportional to at the high region, similar to the N₁ behaviour of polymer blends undergoing shear-induced homogenization. Because the existence of microdomains was confirmed at the high region by the flow birefringence method, it is concluded that the above N₁ behaviour is not caused by shear-induced homogenization, but is probably caused by the shear-induced alignment of the microdomain structure.     

Formation of phase structure and crystallization behavior in blends containing polystyrene–polyethylene block copolymers

The microphase separation structure in the molten state and the structure formation in crystallization from such ordered melt were investigated for the blends of polystyrene–polyethylene block copolymers (SE) with polystyrene homopolymer (PS) and polyethylene homopolymer (PE) and for the blends consisting of two kinds of SE with different copolymer compositions from each other, using synchrotron small-angle X-ray scattering techniques (SAXS). The copolymer compositions of SE block copolymers employed were 0.34, 0.58 and 0.73 wt. fraction of PE, and their melt morphologies were cylindrical, lamellar and lamellar, respectively. Macrophase separation or the morphology change in the melt occurred depending on the molecular weight and the blend composition, as reported so far. In crystallization from such macrophase-separated and microphase-separated melts, the melt morphology was completely kept for all the blends. Crystallization behavior was also investigated for the blends. The crystallization within the spherical and cylindrical domains surrounded by glassy PS was not observed for SE/PS blends. In the crystallization from the macrophase-separated melt, two exothermal peaks were observed in the DSC measurements, while a single peak was observed for other blends. For the blends with PS, the degree of crystallinity was depressed and the apparent activation energy of crystallization was high, compared to those for the corresponding neat SE. For SE/PE and SE/SE blends, those were changed depending on the blend composition.     

Novel CO2 Absorbents Using Lithium-Containing Oxide

We have discovered a series of lithium-containing oxides that immediately react with ambient carbon dioxide (CO₂) up to 700°C. The products react and return reversibly to the oxides at a temperatures higher than about 700°C. The absorption capacity surpasses that of other CO₂ absorbents by a factor of 10. Utilizing these absorbents, the possibility of a CO₂ separation system that operates at around 500°C is proposed. It is generally believed that a CO₂ separation process operable at temperatures higher than 500°C has the special benefit of a small energy penalty. Moreover, the absorption also proceeds at ambient temperature in the atmospheric environment. This property offers the possibility of many other applications, such as air cleaners or cartridges. Therefore, we think these materials have the potential to make a valuable contribution to the realization of CO₂ emission control.     

Reinforcement of polypropylene by cellulose microfibers modified with polydopamine and octadecylamine

Cellulose microfibers (CMFs) having surfaces modified with polydopamine (PDPA) and octadecylamine (ODA) were prepared, and their reinforcing abilities for polypropylene (PP) were investigated. The PDPA coating was made via self-polymerization of dopamine (P-CMF), and subsequent alkylation was conducted by the reaction with ODA (OP-CMF). The modified CMFs exhibited improved dispersibility in the PP matrix due to the reduced hydrophilicity. The OP-CMF/PP composite prepared by batch mixing had a higher tensile modulus compared to that for the pure PP and composites with unmodified CMFs. However, excess alkylation lowered the tensile modulus, and the presence of an optimal degree of alkylation was demonstrated. The CMF/PP-IM composites fabricated by injection molding exhibited improved tensile properties compared to those prepared by batch mixing. Both the tensile modulus and yield stress were increased by increasing the CMF content and improved by the surface modification of the CMFs.     

Forming of aluminium alloy at temperatures just below melting point

In order to improve the mechanical properties of products, a forming process of a solid material at a temperature just below the melting point is proposed. The material is deformed at the semi-solid temperature due to the heat generation caused by plastic deformation. The tensile strength, elongation, hardness and toughness of the aluminium alloy (Al–7%Si–0.3%Mg) billet extruded at temperatures between 500 and 550 °C are compared with those of the billet extruded in the hot forming (450 °C) and the semi-solid (560 °C) temperatures. The billet temperature during forming is evaluated by the finite element simulation. The tensile strength and hardness of the billet extruded at 550 °C just below the solidus temperature are higher than those for a billet at 450 °C, and they are almost the same as those for a billet deformed at 560 °C in the semi-solid region. The elongation and toughness of the extruded billet at 550 °C are lower than those for a billet at 450 °C. The forming load at 550 °C is almost half of that at 450 °C. Cracking on the surface of the extruded billet occurs at a high punch speed. The calculated temperature when the solid billet is extruded in the semi-solid state agrees well with the experimental one at which the tensile and hardness are improved.