Emission of Particulate Matter 2.5 (PM2.5) from Sewage Sludge Incinerators in Japan

Because fine particulate matter ≤2.5 µm in diameter (PM2.5) causes health problems, PM2.5 emissions are of concern. However, little research on stationary sources has been conducted. To determine the concentration and filtration behavior of PM2.5, dust was collected from five fluid-bed sewage sludge incinerators (SSIs) sorted by particle size using cascade impactors. The average PM2.5 concentration was 0.00014–4.8 mg/Nm³. The total estimated amount of PM2.5 emissions from the SSIs for all plants in Japan was 0.96–8.9 tons/year. Since the SSIs with dry Electrostatic Precipitators (EP) contributed 75–99% of the total emissions, replacing dry EPs with bag filters would significantly reduce the PM2.5 emissions from SSI.     

Character motion synthesis by principal component analysis and motion control interface by hands

In this paper, we propose an interactive character motion control interface that uses hands. Using their hands and fingers, the user can control a large number of degrees of freedom at the same time. We applied principal component analysis to a set of sample poses and assigned the extracted principal components to each degree of freedom of the hands (such as the hand positions and finger bending/extending angles). The user can control the blending weights of the principal components and deform the character's pose by moving their hands and bending/extending their fingers. We introduced pose and action controls, so that we can alter the standing pose and perform various actions with deformations. So that various types of actions were possible, we constructed a number of action models in advance. We introduced action model selection and action execution mechanisms. We developed methods for computing the feature vector, for applying principal component analysis, and for pose and action synthesis. In addition, we introduced a pose transition method for performing a step motion when necessary to prevent foot sliding. We present our experimental results and demonstrate the effectiveness of our interface. Copyright © 2015 John Wiley & Sons, Ltd.     

Proposal of a Simple Method for Assessing the Susceptibility of Naturally Deposited Clay Grounds to Large Long-Term Settlement due to Embankment Loading

A simple method that utilizes the results of laboratory tests has been proposed for determining the susceptibility of soft clay grounds to large residual consolidation settlement due to embankment loading. It was found that there is a possibility of large long-term settlement if the sensitivity and compression index ratios of the clay material that constitutes the ground are equal to or more than 8.0 and 1.5, respectively. The compression index ratio is defined in this paper as the ratio (Cc/Ccr) of the steepest gradient of the compression curve of an undisturbed sample to that of the remolded sample. Through the SYS Cam-clay model, an elasto-plastic constitutive model that describes the actions of the soil skeleton structure, it was found that clays with large sensitivity and compression index ratios are characterized by initially highly structured soils and that decay/upgradation of the structure can easily occur due to plastic deformation. In addition, by following Schmertmann's graphic method for in-situ compression curve (1953), this paper proposes a method of deducing the in-situ initial conditions from the results of laboratory consolidation tests on undisturbed samples. These investigations revealed not only that large delayed settlement is facilitated in clays, which have higher degrees of structure and faster rates of structural decay, but also that the Δe method and other simple methods of predicting settlement may underestimate the amount of settlement.     

Control of Snow Falling Flow around NACA0015 Blade using a Plasma Electrode with Weather Resistant Design

The plasma actuation (PA) effect on the snow falling flow was investigated using a plasma electrode with weather resistant design and the natural snow wind facility of the Hokkaido University of Science. NACA0015 test blade with chord length c of 300 mm was used. Wind tunnel tests were carried out under the angle of the attack of the blade was fixed at 15 degrees, and the main flow velocity is U=5 m/s. PIV (Particle image velocimetry) measurements were conducted on various PA conditions using natural dry snowflakes as a tracer. When the actuator was driven under the condition of the fundamental frequency of F=50 kHz, and the pulsed modulated frequency f of fc/U=1 and Duty ratio (Ratio of plasma ON time to pulse duration time) =1%, movement of snowflakes was controlled the most effectively tested. It was clarified that the fundamental frequency of PA also affects the control of snow flow. Under snowfall conditions, the weather resistant designed plasma electrode has suffered no damage and operated successfully.     

Detailed Analysis of Temperature Characteristics of an InGaP/InGaAs/Ge Triple-Junction Solar Cell

Temperature characteristics of an InGaP/InGaAs/Ge triple-junction solar cell were analyzed in detail using an equivalent circuit calculation. The current–voltage (I–V) characteristics of single-junction solar cells (InGaP, InGaAs, Ge solar cells) were measured at various temperatures. Fitting of I–V curves between measured and calculated data was carried out, and the diode parameters and temperature exponents of the single-junction solar cells were extracted. The parameters for each single-junction solar cell were used in the equivalent circuit model for the triple-junction solar cell, and calculations of solar cell performance were carried out. Measured and calculated results of the I–V characteristics at various temperatures agreed well.     

The use of caproic acid to prevent aerobic deterioration of silages after opening,with special reference to the amounts and time of application

The effectiveness of caproic acid (hexanoic acid) addition to silages prepared from Italian ryegrass or cocksfoot (dry matter 16.3–34.5%) in preventing aerobic deterioration after opening was investigated in five experiments with varying amounts and times of application. Silages prepared in PVC bag silos were transferred to expanded polystyrene containers and left in a room at 25°C for 7 days with access to air. Aerobic deterioration was judged by rise in temperature, increase in pH and changes in the counts of yeasts and moulds. A low dry matter silage containing a fairly large amount of butyric acid was stable, and another low dry matter silage was relatively stable. Silages made from wilted grass deteriorated. Application of 50 mmol/kg grass at ensiling prevented deterioration in all cases. The effect was also observed with 50 mmol addition at opening, 10 mmol at ensiling and 10 mmol at opening in that order.     

The relationship between acoustic emission signals and cutting phenomena in turning process

The development of intelligent manufacturing by using machine tools is advancing in leaps and bounds. To maintain accuracy in machining and in the interests of fail-safe operation, monitoring of the cutting state or the final machining is very important. Acoustic emissions (AE) comprise elastic stress waves produced as a result of the deformation and fracture of materials. By measuring the AE generated during a turning process, it is possible to estimate the state of the machining operation. The correlation between cutting phenomena and AE in a turning process was examined experimentally by using a steel workpiece and a cermet tool in a numerically controlled turning process. The process of formation of chips, the types of chip, and the shear angle all markedly affected the AE signals. There was a strong negative correlation between the shear angle and the AE signal level. Similar results were obtained for various feed rates and for workpieces of various degrees of hardness. Correlations related to surface roughness and to tool wear are also described that permit the evaluation of the state of the turning process.     

Production of Fullerenes by Combustion

The progress in the production of fullerenes from flaming soot is reviewed in terms of the experimental conditions, characteristics in the product distribution, and formation mechanisms.     

The use of indoline dyes in a zinc oxide dye-sensitized solar cell

The effects of the position and the type of carboxyl anchor group in double rhodanine-type indoline dyes on the performance of a zinc oxide dye-sensitized solar cell were examined. The optimum position for the carboxymethyl group was on the inner rhodanine moiety; a carboxymethyl group gave optimum results among carboxymethyl, -ethyl, and -propyl derivatives.