Remineralization effects of xylitol on demineralized enamel

We morphologically determined the effects of xylitol on the remineralization of artificially demineralized enamel. The samples were demineralized and then immersed in a remineralizing solution with or without 20% xylitol at 37 degrees C for 2 weeks. Samples were observed using contact microradiography, a multipurpose image processor (MIP) and a high-resolution electron microscope (HRTEM). Contact microradiography indicated that remineralization occurred in the surface and deep layers of samples immersed in a non-xylitol solution. Samples immersed in a xylitol solution demonstrated less mineralization in the outer 10 microm of the outermost surface layers, but more mineralization in the middle and deep layers, than was observed in the non-xylitol samples. The MIP evaluation indicated that remineralization was more prominent in layers at depths of 50-60 microm in the xylitol samples than in the non-xylitol samples. Observation of the xylitol samples by HRTEM revealed crystals of various sizes and irregular shapes with unclear crystal angles in the outermost surface layers. In the middle layers, they had thickened and angles of crystals are clear. These results indicate that xylitol can induce remineralization of deeper layers of demineralized enamel by facilitating Ca2+ movement and accessibility.     

Biodegradable polylactide/montmorillonite nanocomposites

Our continuing research on the preparation, characterization, materials properties, and biodegradability of polylactide (PLA)/organically modified layered silicate (OMLS) nanocomposites has yielded results on PLA/montmorillonite nanocomposites. Montmorillonite (mmt) modified with dimethyldioctadecylammonium cation was used as an OMLS for nanocomposite preparation. The internal structure of nanocomposites on the nanometer scale was established with the use of wide-angle X-ray diffraction patterns and transmission electron micrographic observation. All nanocomposites exhibited significant improvement in crystallization behavior, mechanical properties, flexural properties, heat distortion temperature, and O2 gas permeability when compared with pure PLA.     

A distributed routing method for AGVs under motion delay disturbance

In real transportation environments for semi-conductor manufacturing, unexpected disturbances such as motion delays and/or sudden requests for transportation may cause collisions among AGVs increasing total transportation time. It is required to generate a collision-free routing for multiple automated guided vehicles (AGVs) within a few seconds. In this paper, we propose a distributed routing method under motion delay disturbance for multiple AGVs. The proposed method features a characteristic that each AGV subsystem derives its optimal route to minimize the sum of the transportation time and the penalties with respect to collision probability with other AGVs. The penalties reflect the collision probability distribution function for motion delay disturbances. The proposed method is applied to a routing problem for transportation in the semiconductor fabrication bay with 143 nodes and 20 AGVs. The computational results show that the total transportation time obtained by the proposed method is shorter than that of the conventional method. For dynamic transportation environments, an optimal timing for re-routing multiple AGVs under motion delay disturbance is systematically determined by the tradeoff relationship between the total computation time to derive a solution and the uncertainties for re-routings. Markov chain is used to represent uncertainty distribution for re-routings. The proposed method is implemented in an experimental transportation system with 51 nodes and 5 AGVs. The experimental results demonstrate that the proposed method is applicable to real transportation environments.     

Vacuum seal for a rectangular flange

A new vacuum seal for a rectangular flange used in r.f. equipments, was developed. The vacuum seal consists of a recess with a flat surface, machined into a rectangular flange, a rectangular metal gasket with a raised projection on one face, and a mating flange with a recess and raised projection. No leak greater than 1 × 10⁻¹⁰ Pa m³/s was found in leak tests, before and after baking cycles (100 °C, 12 h).     

Intra-molecular mobility of holes along rod-like helical Si backbones in optically active polysilanes

Intra-molecular mobility of positive charge carriers in poly(n-hexyl-[S]-2-methylbutylsilane) (PHMBS) films doped with N,N′-bis(2,5-di-tert-buthylphenyl)-3,4,9,10-perylenedicarboximide (PDI) is studied by time-resolved microwave conductivity (TRMC) measurements. PHMBS with optically active side chains has a rod-like tightly locked Si catenation with unlikely long persistence length compared with conventional dialkyl-substituted polysilanes. It was found that PDI is a suitable electron acceptor for PHMBS as it provides the high product of photo carrier generation yield ? as ～0.08% under an excitation at 355 nm. The efficient electron transfer reaction from PHMBS to PDI gives clear conductivity transients ascribed to the positive charges on the Si catenation of PHMBS by TRMC measurements. The estimated value of isotropic mobility along the tightly locked Si catenation is 0.36 cm² V^?1 s^?1, suggesting the presence of mobile holes on the backbones of PHMBS.     

Risk assessment of airborne fine particles and nanoparticles

Pulmonary health effects of fine particles and nanoparticles are overviewed in this paper, mainly based on the researches conducting in our laboratory. For the hazard assessment, we exposed rats to aerosolized asbestos-substitutes or nanoparticles aerosols (nickel oxide and titanium dioxide), and examined the biological and pathological effects of the particle on lung, a major target organ for the particles, and cytokines which are related to inflammation, fibrosis and carcinogenesis in the lung. It is essential to perform comprehensive evaluation of the toxicity of poorly soluble powder samples using the precise characterization data and exposure methods, such as single instillation or aerosol inhalation.     

Organic LED full-color passive-matrix display

Abstract— A full-color 5.2-inch 1/4-VGA passive-matrix organic LED display has been developed, adopting selective deposition for the different emitting materials. The display features 320 (×3) × 240 pixels with an equivalent pixel size of 0.33 × 0.33 mm, white peak luminance of over 150 cd/m², and power consumption of 6 W.     

Fabrication of 0.95Sn−0.05Au solder micro-bumps for flip-chip bonding

This letter describes the successful fabrication of a 0.95Sn−0.05Au solder microbump on a compound semiconductor wafer by reflowing of multi-layer metal film. Since the inherent interdiffusion in Au−Sn phases results in the alloying of multi-layer films, the composition of micro-bump is well controlled by the thickness of constituent metal films. The micro-bumps melt at about 220 C, which is close to the lowest eutectic temperature in a Au−Sn system. Solder bonding using 0.95Sn−0.05Au micro-bump is a very useful technique for the flipchip bonding of compound semiconductor devices.