Anhydrous proton conductor consisting of pectin–inorganic composite material

An organic–inorganic proton conductive composite material consisting of a biopolymer was prepared by mixing the pectin, tetraethyl titanate, and imidazole. Although the pectin material without the composite dissolved in water, the pectin–inorganic composite material did not show water solubility. In addition, in the composite material, the pectin and imidazole formed an acid–base structure by an electrostatic interaction, and as a result, these composite materials showed a thermal stability at intermediate temperatures (100–200°C). Furthermore, these composite materials indicated the proton conductivity of 5.6 × 10^?4 S cm^?1 at 180°C under anhydrous conditions. The activation energy of the proton conduction under anhydrous conditions was 0.32–0.22 eV and these values were one order of magnitude higher than that of the typical humidified perfluorinated membrane, such as Nafion^®. The organic–inorganic composite material consisting of a biocomponent may have the potential to be utilized as a novel proton conductor under anhydrous conditions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42433.     

Unsteady behavior of leading-edge vortex and diffuser stall in a centrifugal compressor with vaned diffuser

The characteristics of a rotating stall of an impeller and diffuser and the evolution of a vortex generated at the diffuser leading-edge (i.e., the leading-edge vortex (LEV)) in a centrifugal compressor were investigated by experiments and numerical analysis. The results of the experiments revealed that both the impeller and diffuser rotating stalls occurred at 55 and 25 Hz during off-design flow operation. For both, stall cells existed only on the shroud side of the flow passages, which is very close to the source location of the LEV. According to the CFD results, the LEV is made up of multiple vortices. The LEV is a combination of a separated vortex near the leading- edge and a longitudinal vortex generated by the extended tip-leakage flow from the impeller. Therefore, the LEV is generated by the accumulation of vorticity caused by the velocity gradient of the impeller discharge flow. In partial-flow operation, the spanwise extent and the position of the LEV origin are temporarily transmuted. The LEV develops with a drop in the velocity in the diffuser passage and forms a significant blockage within the diffuser passage. Therefore, the LEV may be regarded as being one of the causes of a diffuser stall in a centrifugal compressor.     

Acceleration of the redox kinetics of VO2+/VO2 + and V3+/V2+ couples on carbon paper

The redox kinetics of VO²⁺/VO₂ ⁺ and V³⁺/V²⁺ couples on a carbon paper (CP, HCP030 N, Shanghai Hesen, Ltd., China) electrode were investigated in terms of their standard rate constant (k ₀) and reaction mechanism. The values determined for k ₀ for VO²⁺ ?? VO₂ ⁺ and V³⁺ ?? V²⁺ using the CP electrode are 1.0 × 10^?3 and 1.1 × 10^?3 cm s^?1, respectively. The value of k ₀ increases by one or two order(s) of magnitude compared with values obtained using electrodes composed of pyrolytic graphite and glassy carbon. The acceleration of the redox kinetics of vanadium ions is a result of the large surface area of the CP electrode. An inner-sphere mechanism for the reaction on the surface of the electrode is proposed. The kinetic features of vanadium redox reactions on the CP electrode reveal that CP is suitable for use as the electrodes in vanadium redox-flow batteries.     

Decomposition characteristics of biodegradable plastics made from sago starch‐extraction residue

Biodegradable plastics were synthesized for the effective use of sago starch‐extraction residue, which has been discarded as a waste. Two types of esterified sago starch‐extraction residue, P‐SP and L‐SP, were obtained. It had black color for P‐SP₁₆₀ (esterified by palm oil) to light yellow color for L‐SP₈₀ (esterified by lauric acid) and showed high carbon content, ranging from 399.3 to 537.1 g kg⁻¹. Biodegradable plastics from the residue, which had high esterification degree showed thermoplasticity and slower decomposition in Andisols in Japan and Inceptisols in Philippines. The esterification degrees of P‐SP₁₆₀ and L‐SP were 3.23 and 2.95 to 5.18 mmol g⁻¹, respectively. In addition, L‐SP₈₀ exhibited the most appropriate thermal softening behavior by heating. The cumulative decomposition of P‐SP₁₆₀ in Andisols and Inceptisols showed 16.7 and 32.8% of total carbon during 31 day of the incubation. On the other hand, the decomposition rates of L‐SP₈₀ in Andisols and Inceptisols were less than 10% of total carbon during 31 day of the incubation. The addition of triacetin as plasticizer to P‐SP₁₆₀ and L‐SP₈₀ remarkably influenced the decomposition rate of both molded P‐SP₁₆₀ and L‐SP₈₀. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Optical assessment of silicon nanowire arrays fabricated by metal-assisted chemical etching

Silicon nanowire (SiNW) arrays were prepared on silicon substrates by metal-assisted chemical etching and peeled from the substrates, and their optical properties were measured. The absorption coefficient of the SiNW arrays was higher than that for the bulk silicon over the entire region. The absorption coefficient of a SiNW array composed of 10-μm-long nanowires was much higher than the theoretical absorptance of a 10-μm-thick flat Si wafer, suggesting that SiNW arrays exhibit strong optical confinement. To reveal the reason for this strong optical confinement demonstrated by SiNW arrays, angular distribution functions of their transmittance were experimentally determined. The results suggest that Mie-related scattering plays a significant role in the strong optical confinement of SiNW arrays.     

Improvement of carrier diffusion length in silicon nanowire arrays using atomic layer deposition

To achieve a high-efficiency silicon nanowire (SiNW) solar cell, surface passivation technique is very important because a SiNW array has a large surface area. We successfully prepared by atomic layer deposition (ALD) high-quality aluminum oxide (Al₂O₃) film for passivation on the whole surface of the SiNW arrays. The minority carrier lifetime of the Al₂O₃-depositedSiNW arrays with bulk silicon substrate was improved to 27 μs at the optimum annealing condition. To remove the effect of bulk silicon, the effective diffusion length of minority carriers in the SiNW array was estimated by simple equations and a device simulator. As a result, it was revealed that the effective diffusion length in the SiNW arrays increased from 3.25 to 13.5 μm by depositing Al₂O₃ and post-annealing at 400°C. This improvement of the diffusion length is very important for application to solar cells, and Al₂O₃ deposited by ALD is a promising passivation material for a structure with high aspect ratio such as SiNW arrays.     

Effects of dressing containing plant sterol on serum cholesterol concentration and the safety evaluation in borderline or mildly hypercholesterolemic Japanese subjects

In a placebo-controlled double-blind study, we examined the effects of dressing containing plant sterol (PS) on blood lipids and the safety in Japanese borderline or mildly hypercholesterolemic subjects. Fifty-nine subjects [total cholesterol (TC) concentration > or = 200 mg/dL] were randomly divided into two groups and were given daily 15 g of dressing containing 800 mg of PS [PS(+)-group] or without PS [PS(-)-group] for 12 weeks. Every 4 weeks, fasting blood was examined and subjective symptoms were analyzed. Serum TC, low-density lipoprotein cholesterol (LDL-C) and apolipoprotein B (ApoB) concentrations did not change in the PS(-)-group, while TC and ApoB significantly decreased in the PS(+)-group at 8 and 12 weeks and LDL-C at 4, 8 and 12 weeks. Moreover, serum TC, LDL-C and ApoB concentrations were significantly lower than those of PS(-)-group at 8 and 12 weeks. Other laboratory tests were all in normal ranges and no adverse events were observed. The results indicated that PS-containing dressing decreased serum TC, LDL-C and ApoB concentrations in borderline or mildly hypercholesterolemic subjects. It is therefore proved that the dressing containing PS is helpful in maintaining blood cholesterol level normal and hence, the health of Japanese.     

Mouse Gastric Epithelial Cells Resist CagA Delivery by the Helicobacter pylori Type IV Secretion System

The initial step in bacterial infection is adherence of the bacterium to the target cell surface. Helicobacter pylori exploits the interaction of bacterial adhesin protein HopQ with human epithelial CEACAMs (CEACAM1, 5, and 6) to stably adhere to gastric epithelial cells, which is necessary for delivery of the H. pylori CagA oncoprotein into the epithelial cells via a type IV secretion system. In contrast to human CEACAMs, however, HopQ does not interact with Ceacam1 (mouse CEACAM1) in vitro or in CHO cells ectopically expressing Ceacam1. Since the mouse genome lacks Ceacam5 and Ceacam6, no significant HopQ–Ceacam interaction may occur in mouse gastric epithelial cells. Here, we found that the mouse stomach has a much lower expression level of Ceacam1 than the expression level of CEACAM1 in the human stomach. Consistently, mouse gastric epithelial cells resist CagA delivery by cagA-positive H. pylori, and the delivery is restored by ectopic expression of human CEACAM1 or CEACAM5 in mouse gastric epithelial cells. Thus, despite the fact that mice are routinely used for H. pylori infection studies, a low expression level of Ceacam1 in the mouse stomach together with the loss or greatly reduced interaction of HopQ with Ceacams make the mouse an inappropriate model for studying the role of H. pylori-delivered CagA in gastric pathogenesis, including the development of gastric cancer.     

Numerical simulation on void bubble dynamics using moving particle semi-implicit method

In present study, the collapse of void bubble in liquid has been simulated using moving particle semi-implicit (MPS) code. The liquid is described using moving particles and the bubble–liquid interface was set to be vacuum pressure boundary without interfacial heat mass transfer. The topological shape of bubble can be traced according to the motion and location of interfacial particles. The time dependent bubble diameter, interfacial velocity and bubble collapse time were obtained under wide parametric range. The comparison with Rayleigh and Zababakhin's prediction showed a good agreement which validates the applicability and accuracy on MPS method in solving present momentum problems. The potential void induced water hammer pressure pulse was also evaluated which is instructive for further material erosion study. The bubble collapse with non-condensable gas has been further simulated and the rebound phenomenon was successfully captured which is similar with vapor-filled cavitation phenomenon. The present study exhibits some fundamental characteristics of void bubble hydrodynamics and it is also expected to be instructive for further applications of MPS method to complicated bubble dynamics problems.