Conjugate heat transfer of laminar mixed convection of a nanofluid through an inclined tube with circumferentially non-uniform heating

Laminar mixed convection of a nanofluid consisting of water and Al₂O₃ in an inclined tube with heating at the top half surface of a copper tube has been studied numerically. The bottom half of the tube wall is assumed to be adiabatic (presenting a tube of a solar collector). Heat conduction mechanism through the tube wall is considered. Three-dimensional governing equations with using two-phase mixture model have been solved to investigate hydrodynamic and thermal behaviours of the nanofluid over wide range of nanoparticle volume fractions. For a given nanoparticle mean diameter the effects of nanoparticle volume fractions on the hydrodynamics and thermal parameters are presented and discussed at different Richardson numbers and different tube inclinations. Significant augmentation on the heat transfer coefficient as well as on the wall shear stress is seen.     

Microstructural evolution of a commercial ultrafine alumina powder densified by different methods

The densification and grain growth of bodies made from a commercial ultrafine alumina powder was investigated. The primary powder was initially subjected to dry (uniaxial cold pressing) and wet shaping (slip casting), followed by conventional (CS)-, two step (TSS)-, and microwave (MS) sintering to explore the effect of each series of treatments on the densification and microstructural evolution of the specimens. It was demonstrated that a uniform microstructure with higher density would be obtained using the wet shaping method. In addition, microwave sintering was found to be more effective into the densification of the specimens and in yielding a finer grain structure. It is believed that the high heating rate and effective particle packing are responsible for the improvements in these properties. On this basis, it was also demonstrated that the fracture toughness of the samples increased significantly through the application of microwave sintering.     

Theoretical and practical investigations of copper ion selective electrode with polymeric membrane based on N,N′-(2,2-dimethylpropane-1,3-diyl)-bis(dihydroxyacetophenone)

A novel ion-selective poly(vinyl chloride) (PVC) membrane sensor for Cu²⁺ ions based on N,N′-(2,2-dimethylpropane-1,3-diyl)-bis(dihydroxyacetophenone) (NDHA) as a new ionophore was prepared and studied. The best performance was observed for the membrane composition, including 30:65:1:4 (wt%) = PVC:DBP:KTpClPB:NDHA. The electrode showed a good Nernstian slope of 30.0 ± 0.5 mV/decade in a wide linear range activity of 3.0 × 10⁻⁷ to 1.0 × 10⁻² mol dm⁻³ Cu(NO₃)₂ with limit of detection 2.5 × 10⁻⁷. Sensor exhibited a fast response time (t_95% < 10 s) and could be used for about 4 months in the pH range of 3.0–7.4. The proposed potentiometric sensor was found to work satisfactorily in partially non-aqueous media up to 30 (vol%) content of methanol, ethanol and acetone. Applications of this electrode for the determination of copper in real samples, and as an indicator electrode for potentiometric titration of Cu²⁺ ion using EDTA, were reported. In order to predict the extraction ability of NDHA for different metallic ions, the complexes [M(NDHA)] and [M(H₂O)₆] (where M = Cu²⁺, Co²⁺, Hg²⁺, Pb²⁺, Ag⁺, Mg²⁺, Ca²⁺, Mn²⁺, Zn²⁺, Cd²⁺, K⁺ and Al³⁺) were investigated using ab initio theoretical calculations. The metal binding capability was evaluated using the binding energy. Results of our study could be useful for prediction of the extraction power of this Schiff base and could play a guiding role in planning experiments.     

A study on the effect of compositing silver oxide nanoparticles by carbon on the ‎electrochemical behavior and electronic properties of zinc‐silver oxide batteries ‎

In this study, the effect of compositing silver oxide nanoparticles by carbon on the electrochemical behavior and electronic properties of zinc‐silver oxide batteries have been investigated. For this purpose, firstly four silver oxide electrodes containing 5, 10, 15, and 20 wt% carbon powder were produced by powder metallurgy method. For the next step, all four silver oxide electrodes were sintered at 500°C for 10 minutes. Afterward and in order to investigate the microstructure, phase and elemental analysis of the electrodes were carried out using Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), X‐ray Diffraction (XRD), and Energy Dispersive Spectroscopy (EDS), respectively. Moreover, in order to investigate the effect of compositing silver oxide nanoparticles by carbon on the electrochemical behavior and electronic properties of zinc‐silver oxide, electrochemical tests (potentiodynamic polarization and electrochemical impedance spectroscopy) and electric discharge test in 1.4 wt%KOH electrolyte were carried out respectively. The microstructural observations revealed that increasing carbon content in the silver oxide electrodes results in increasing the apparent porosities in these electrodes. Investigating the phase and elemental analysis results showed that by increasing the content of carbon in the silver oxide electrode, the amount of Ag₂O and AgO phases in this electrode reduces and also the extent of pure silver formation increases. Investigations on the results of electrochemical tests showed that increasing carbon content results in the reduction of corrosion resistance in silver oxide electrodes. Moreover, the results of electric discharge test revealed that the silver oxide electrode containing 10wt% carbon yields the highest energy efficiency in the zinc‐silver oxide batteries.     

Microwave Synthesis and Characterization of Spinel-type Zinc Aluminate Nanoparticles

In the present work, ZnAl₂O₄ nanoparticles have been synthesized with the aid of Zn(OAc)₂·2H₂O and Al(NO₃)₃·9H₂O as starting reagents in the presence of microwave irradiation. Besides, the effect of preparation parameters such as microwave power and irradiation time on the morphology and particle size of products was studied by SEM images. The as-prepared ZnAl₂O₄ nanoparticles were characterized extensively by techniques like XRD, TEM, SEM, FT-IR, PL, and EDS. Photoluminescence studies of the ZnAl₂O₄ nanoparticles displayed quantum confinement behavior with band gap of 3.2 eV. The XRD studies showed that pure orthorhombic ZnAl₂O₄ nanoparticles have been produced after calcination.     

CuIns2/Cus Nanocomposite: Synthesis via Simple Microwave Approach and Investigation Its Behavior in Solar Cell

CuInS₂/CuS nanocomposite were synthesized by a copper complex, [bis(ethylenediamine)copper(ΙΙ)] sulfate. Eight sulfur sources were used for this experiment. The products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray analysis spectroscopy, and room temperature photoluminescence spectroscopy. Thin film of nanocomposite powder was fabricated and its feature (V_oc, J_sc and FF) was calculated by current–voltage (I–V) curve.     

Thermal degradation behavior and kinetic studies of polyacrylamide gel in TiO2 nanoparticles synthesis

Polyacrylamide gel (PAMG) method is a simple, fast and cheap method used for the synthesis of a wide variety of nanopowders. However, no adequate results have been reported on the thermal degradation behavior of PAMG which can be very effective on the final product properties. In this work, thermal degradation behavior of PAMG in the presence of TiCl₄ as a precursor salt for synthesis of TiO₂ nanoparticles was examined in comparison with linear polyacrylamide (LPAM) and pure PAMG by thermogravimetry/differential thermal analysis. Their thermal degradation kinetics was investigated, as well. The results showed that thermal degradation of all samples occurred in two stages at different onset temperatures. Despite the high thermal stability of pure PAMG compared to LPAM, the presence of TiCl₄ as a mineral material in PAMG structure decreases the thermal degradation onset temperature, considerably. Furthermore for LPAM and PAMG, majority of weight loss occurs in the second stage, but in PAMG with TiCl₄ the weight loss occurs mainly at the first stage. For more detailed investigation, residual materials were characterized by Fourier transform infrared spectroscopy and X-ray diffraction (XRD) techniques, attributing this trend to the presence of mineral materials in PAMG structure. XRD and transmission electron microscopy were also applied to confirm anatase crystalline structure and nanoscale distribution of the TiO₂ particles synthesized via PAMG method.     

Optimization of stress wave propagation in a multilayered elastic/viscoelastic hybrid composite based on carbon fibers/carbon nanotubes

The hypothesis of incorporating carbon nanotubes (CNTs) into the interfacial layers of fiber‐reinforced polymer composites fiber‐reinforced Polymers (FRPs) to enhance their mechanical properties and mitigate the stress wave propagation during a blast event is investigated. A numerical model is developed to simulate the stress wave propagation in a laminated elastic/viscoelastic FRP. Coupled with multiobjective optimization paradigms, the optimal CNTs contents in the interfacial layers are determined to minimize the stress‐to‐strength ratio in each layer. A case study demonstrating the design of a five‐layered FRP subjected to a blast event is presented. The simulation revealed that the viscoelastic properties of the matrix material contribute significantly to the energy dissipation during stress wave propagation. It is shown that addition of 0.69% CNTs by volume to the epoxy interface significantly enhances the ability of composite to resist blast loading. Results were compared with a standard model that assumes only elastic behavior. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Hydrodynamic and heat transfer properties of magnetic fluid in porous medium considering nanoparticle shapes and magnetic field-dependent viscosity

The purpose of this paper is to study the characteristics of the combined convection heat transfer and a micropolar nanofluid flow passing through an impermeable stretching sheet in a porous medium. The nanofluid flow field is affected by a magnetic field perpendicular to the sheet. The dynamic viscosity of the micropolar nanofluid changes under the influence of the magnetic field. The continuity, linear momentum, angular momentum, and energy equations are first simplified using the order of magnitude technique that, along with the applied boundary conditions and the definition of the appropriate parameters, are transferred to the similarity space using the similarity analysis. Then the resulting equations are solved using the Runge–Kutta method.The distinction of the macroscale and microscale flow fields and temperature fields resulting from different nanoparticle shapes was clarified. Increasing the Hartmann number, the vortex viscosity parameter, the magnetic parameter, the nanoparticle volume fraction, and the permeability parameter of the porous media increased the surface friction on the sheet. Increasing the vortex viscosity parameter, the magnetic parameter, and the volume fraction of the nanoparticles increases the Nusselt number.     

PEG-PLA-PCL based electrospun yarns with curcumin control release property as suture

This work presents an interesting method using an electrospinning process to fabricate suture yarns loaded with curcumin to achieve reasonable mechanical properties as well as tunable drug release behavior. Different structures including different yarn counts and twists as well as core-sheath structures were used to adjust drug release properties along with improving the yarn's mechanical properties. The core parts were made of polycaprolactone and the sheath parts were made of polyethylene glycol, polylactic acid, and polycaprolactone. Drugs can be incorporated in both parts based on the required condition and application. Electrospun yarns were compared using both structural properties and their drug release profiles as metrics. The results of comparing drug release profiles of six electrospun yarns with different yarn counts and twists showed that yarns with finer fiber diameters in the core part have more drug release as well as more initial release. Overall evaluations showed that core-sheath drugloaded yarn with appropriate physical and mechanical properties can be a useful material as a drug delivery system to the site of damaged tissue. It can also be concluded that the amount and duration of drug release can be controlled using the structural parameters of electrospun yarns as an engineering tool for designing suture yarns with required properties.