Ochratoxin A in dried vine fruit: method development and survey

A method is described for the determination of concentrations of the mycotoxin ochratoxin A in dried vine fruits (currants, raisins and sultanas) using acidic methanolic extraction,immunoaffinity chromatography clean-up and HPLC determination. The limit of detection was estimated as 0.2mug/kg, and recoveries of 63-77% were achieved at 5mug/kg. HPLC-mass spectrometric confirmation of the identity of ochratoxin was obtained. Ochratoxin A and aflatoxins were determined in 60 samples of retail dried vine fruits purchased in the United Kingdom. Ochratoxin A was found in excess of 0.2mug/kg in 19 of 20 currant, 17 of 20 sultana and 17 of 20 raisin samples examined, an overall incidence of 88% . The maximum level found was 53.6mug/kg. No aflatoxin was found in any sample analysed, using a method with a detection limit of 0.2mug/kg for each of aflatoxin B1, B2, G1 and G2.     

Mechanical properties of poly(ethylene terephthalate) modified with functionalized polymers

This study examined the effect of blending poly(ethylene terephthalate) (PET) with 5% of a functionalized polymer. The blends were characterized by particle size and size distribution, unnotched tensile behavior, toughness, and notch sensitivity. The improved properties of blends that incorporated a functionalized elastomer were consistent with in situ formation of a graft copolymer by reaction with PET end groups. Triblock copolymers were examined that had styrene end blocks and an ethylene/butylene midblock (SEBS) with grafted maleic anhydride. The present study extended previous investigations that focused on level of grafting to examine the effects of component molecular weight and PET hydroxyl‐to‐carboxyl end‐group ratio. Increasing the molecular weight of the SEBS and decreasing the hydroxyl‐to‐carboxyl ratio of the PET increased the effectiveness of the SEBS. In addition, a mix of an unfunctionalized SEBS with a functionalized SEBS was more effective than a single SEBS with the same total anhydride content. The same elastomers were the most effective for modifying a lower molecular weight PET (intrinsic viscosity 0.73) and a higher molecular weight PET (intrinsic viscosity 0.95). Some functionalized polypropylenes included in the study did not enhance the properties of PET. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 203–219, 1999     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Molecular epidemiology and cluster analysis of human listeriosis cases in three U.S. states

To better understand the transmission and epidemiology of human listeriosis, 647 Listeria monocytogenes isolates obtained from human listeriosis cases in four U.S. locations (Michigan, Ohio, New York State, and New York City) over 61 months (1998 to 2003) were characterized by automated EcoRI ribotyping. A total of 65 ribotypes were differentiated among the characterized isolates; 393, 227, and 24 isolates were classified into lineages I, II, and III, respectively, and 3 isolates were not classified to lineage. The three most common ribotypes (responsible for 39% of all cases) represented L. monocytogenes epidemic clones, each of which had previously been linked to at least two human listeriosis outbreaks. Categorical analyses revealed that ribotypes and lineages were nonrandomly distributed among the four locations. Temporal cluster analysis of cases identified 13 statistically significant temporal subtype clusters, which represented 26% of all cases. Three of these clusters matched previously described human listeriosis outbreaks. Isolates involved in clusters belonged to nine ribotypes. Four, eight, and one cluster were caused by lineages I, II, and III, respectively. The two largest clusters were both caused by the epidemic clone representing ribotype DUP-1044A. Categorical analyses revealed no significant associations between lineage or ribotype and clinical manifestation (central nervous system infection, septicemia, fetal infection, or other infection) or disease outcome (fatal or not fatal). Although human listeriosis cases are caused by isolates belonging to a diversity of EcoRI ribotypes, specific lineage I epidemic clones cause a large number of human listeriosis cases. Many human listeriosis cases can be grouped into statistically significant temporal clusters, including widely distributed and region-specific clusters associated with isolates of various ribotypes. L. monocytogenes lineages and EcoRI ribotypes do not appear to differ in their likelihood of causing different clinical manifestations or mortality.     

Retene emission from residential solid fuels in China and evaluation of retene as a unique marker for soft wood combustion

Retene (1-methyl-7-isopropylphenanthrene) is often used as a marker for softwood combustion and for polycyclic aromatic hydrocarbon (PAH) source apportionment. The emission factors of retene (EF(RET)s) from 11 crop residues, 27 firewood fuels, and 5 coals were measured using traditional rural Chinese stoves. Retene was measured in combustion emissions from all of the residential fuels tested and EF(RET)s varied significantly among the fuels due to the differences in fuel properties and combustion conditions. EF(RET)s for pine (0.34 ± 0.08 mg/kg) and larch (0.29 ± 0.22 mg/kg) were significantly higher than those of other wood types, including fir and cypress (0.081 ± 0.058 mg/kg). However, EF(RET)s for crop residues varied from 0.048 ± 0.008 to 0.37 ± 0.14 mg/kg and were not significantly lower than those for softwood (0.074 ± 0.026 to 0.34 ± 0.08 mg/kg). The EF(RET)s for coal were very high and ranged from 2.2 ± 1.5 (anthracite briquette) to 187 ± 113 mg/kg (raw bituminous chunk). EF(RET) was positively correlated with EFs of coemitted particulate matter (EF(PM)) and phenanthrene (EF(PHE)) for crop residue and coal, but not for wood. In addition, the ratios of EF(PHE)/EF(RET) and EF(PM)/EF(RET) for coals were much lower than those for crop residues and wood. These data suggest that retene is not a unique PAH marker for softwood combustion and that coal combustion, in particular, should be taken into account when retene is used for PAH source apportionment.     

On the frame-error rate of concatenated turbo codes

Turbo codes with long frame lengths are usually constructed using a randomly chosen interleaver. Statistically, this guarantees excellent bit-error rate (BER) performance but also generates a certain number of low weight codewords, resulting in the appearance of an error floor in the BER curve. Several methods, including using an outer code, have been proposed to improve the error floor region of the BER curve. We study the effect of an outer BCH code on the frame-error rate (FER) of turbo codes. We show that additional coding gain is possible not only in the error floor region but also in the waterfall region. Also, the outer code improves the iterative APP decoder by providing a stopping criterion and alleviating convergence problems. With this method, we obtain codes whose performance is within 0.6 dB of the sphere packing bound at an FER of 10^-6     

A common intermediate language and its use in partitioning concurrent declarative programs

The plethora of concurrent declarative language families, each with subtly different semantics, makes the design and implementation of static analyses for these languages a demanding task. However, many of the languages share underlying structure, and if this structure can be exploited, static analysis techniques can be shared across language families. These techniques can thus provide a common kernel for the implementation of quality compilers for this entire language class. The purpose of this paper is to exploit the similarities of non-strict functional and concurrent logic languages in the design of a common intermediate language (CIL). The CIL is introduced incrementally, giving at each step the rationale for its extension. As an application, we present, in CIL form, some state-of-the-art static partitioning algorithms from the literature. This allows us to “uncover” the relative advantages and disadvantages of the analyses, and determine promising directions for improving static partitioning.     

The use of visual modeling in designing a manufacturing process foradvanced composite structures

Visual modeling is the depiction of abstractions of reality using visual representation of the phenomena being studied. These visual representations include graphs, maps, flowcharts, and pictures. Iconic programming includes the construction and implementation of models using this representation. The result can be readily exercised and assessed by experts, thereby helping to ensure the accuracy of the model and its usefulness in supporting the relevant decision process. This paper discusses visual modeling and demonstrates its usefulness in a case study of the design of a manufacturing process involving composite materials and associated manufacturing technologies     

Preschooler's ability to decide whether a photographed unfamiliar object can move itself.

Does the preschooler's use of the animate–inanimate distinction reflect knowledge about which category types engage in self-initiated movements? Three- and 4-year-olds viewed photographs of unfamiliar objects, including mammalian animals, nonmammalian animals, statues with animal-like forms and parts, wheeled vehicles, and multipart rigid objects, and decided whether each item could go up and down a hill by itself. Four-year-olds were reliably accurate about the movement potentials for each of the five classes of items; 3-year-olds' scores were significantly above chance in all but one category. Analyses of rule use and verbalization data showed that children were concerned about cause of movement and used an animate–inanimate hierarchy. Explanations from both age groups varied, in a consistent manner, the kind of information and criteria used to make inferences as function of the type of item. We discuss how these data bear on a theory of concepts. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Chemical mediation of behavior in hermit crabs: Alarm and aggregation cues

Field studies with three common local species of hermit crabs,Clibanarius vittatus, Pagurus longicarpus, andPagurus pollicaris, showed that these crabs responded behaviorally to chemicals originating from crushed conspecifics. Hermit crabs are attracted specifically and in a manner similar to previously reported crab responses to odors from dead gastropods. Responses byC. vittatus to both kinds of odor are of three types: (1) aggregation/shell investigation responses (previously reported for odors from dead gastropods), characterized by increased locomotor activity, investigation of shells in the vicinity, and switching into empty shells; (2) alarm responses, in which crabs flee the area; and (3) withdrawal responses, in which crabs pull into their shells and do not come out. Studies withC. vittatus showed that the stimulatory chemicals originate from hemolymph, are less than 500 D, adsorb to octadecyl silica, and are recovered by elution with 20% methanol. Responses ofC. vittatus are dependent upon crab size, type of shell occupied, and shell fit. Chemicals originating from dead conspecifics provide a forum for shell acquisition by crabs in relatively small shells and alarm by crabs in relatively large shells.