Investigation into the synergistic effects in ternary cementitious systems containing portland cement, fly ash and silica fume

This research was primarily conducted to verify the presence of synergistic effects in ternary cementitious systems containing portland cement (OPC), class C fly ash (FA) and silica fume (SF). A subsequent objective of the study was to quantify the magnitude of the synergy and to determine its source. For a ternary mixture containing 20% FA and 5% SF by mass, the synergistic effect was observed mostly at later ages (7 days onward) and it resulted in an increased compressive strength and resistance to chloride ion penetration as well as a reduced rate of water absorption (sorptivity) compared to predictions based on individual effects of FA and SF in respective binary systems. The observed synergy was attributed to both chemical and physical effects. The chemical effect manifested itself in the form of an increased amount of hydration products. The physical effect associated with packing density was, somewhat contrary to general belief, not due to an optimized particle size distribution of the binder components of the ternary cementitious system. Instead, it was the result of smaller initial inter-particle spacing caused by lower specific gravities of both FA and SF which, in turn, led to a lower volumetric w/cm. If the mixture design was adjusted to account for these differences, the physical effect would be diminished.     

Complex modification effect of linseed cake as an agricultural waste filler used in high density polyethylene composites

Linseed cake (LC) is a by-product of agricultural industry which does not have any large-scale industrial applications. The possibilities of its utilization as filler with plasticizing ability for high density polyethylene (HDPE)-based composites have been investigated. Composites containing 5, 10, 20 and 30 wt% of the waste filler have been prepared using a melt mixing method. The influence of the LC on the mechanical and thermomechanical properties of the composites, as well as their water absorption and morphology, have been evaluated by the following methods: static tensile test, impact strength assessment using Dynstat method, hardness measurements, differential scanning calorimetry, dynamic mechanical thermal analysis, scanning electron microscopy observations, measurements of Vicat’s softening temperature and water uptake test. Application of different measuring techniques allows for describing complex modification effects of the composites’ properties changes induced by the presence of lignocellulosic filler with high oil content. The results of the study proved a pronounced influence of LC on high density polyethylene-based composites, especially a plasticizing effect of crude linseed oil contained by the waste filler particles. LC also has been assumed to affect the polymeric matrix crystallization process. It was found that complex modification of polyethylene results from simultaneously occurring different phenomena including: plasticization of the HDPE by linseed oil, improved crystallinity of the semicrystalline matrix, presence of the rigid lignocellulosic particles dispersed in polymer and accumulation of the oil in the interfacial regions.     

Nonisothermal crystallization of highly‐filled polyolefin/calcium carbonate composites

Nonisothermal crystallization kinetics of highly‐filled polyolefin composites was studied by means of differential scanning calorimetry (DSC). Two types of commercial calcium carbonate based fillers (modified with stearic acid and nonmodified one) were used for our investigations. In order to evaluate the crystallization kinetics changes of composites, the Avrami theory modified by Jeziorny was used. Validity of mineral fillers modification with stearic acid has been proved by thermal analysis. Because of the suppression of the heterogeneous nucleation effect resulting from calcium carbonate with stearic acid modification, an increase in the processability of highly‐filled polyolefin cast films might occur. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41201.     

Solid‐State NMR Study of Mn2+ for Ca2+ Substitution in Thermally Processed Hydroxyapatites

In the present study calcium hydroxyapatites enriched at 0.08 wt% in Mn²⁺ ions (Mn–HA) and their unsubstituted forms (HA) were synthesized using the same standard wet chemical route. Mn‐HA and HA were both calcined at 800°C to give Mn‐HAc and HAc, respectively or sintered at 1250°C, to give Mn‐HAs and HAs, respectively. The influence of the heat treatment on physicochemical properties of Mn‐HA was investigated using powder X‐ray diffraction (PXRD), scanning, and transmission electron microscopy (SEM and TEM), and solid‐state nuclear magnetic resonance (ssNMR). Mn‐HAc and Mn‐HAs were compared to each other and to HAc and HAs, respectively. Assignment of the proton ssNMR peaks from high‐temperature‐treated apatites has been revised. It was found that Mn–HAc and HAc were nanocrystalline, while Mn‐HAs and HAs comprised micrometer sized, partially fused particles (SEM and TEM). PXRD and ssNMR demonstrated that the incorporation of Mn²⁺ into the crystal lattice of hydroxyapatite significantly facilitates its dehydroxylation and decomposition to oxyhydroxyapatite during calcination at 800°C, and induces its transformation to tetracalcium phosphate (TTCP) and alpha‐tricalcium phosphate (α‐TCP) at 1250°C. Contamination by CaO has also been detected. The ¹H→³¹P NMR cross‐polarization experiments have indicated that the Mn²⁺ ions preferentially occupied the Ca(I) position in the crystallographic unit cell of Mn‐HAc. In Mn‐HAs, the Mn²⁺ ions were evenly distributed between the Ca(I) and Ca(II) positions.     

Developing electrochemical measurements in order to assess anti-corrosive coatings more effectively

The aim of this project was to check reproducibility of results obtained using NOCS (no connection to the substrate) arrangement of the electrochemical noise method (ENM). NOCS involves taking measurements from three nominally identical areas on the coated surface. Thus, no electrical connection to substrate is required. In practice the areas are not identical and various arrangements for connection of the three cells were tried to see if the individual areas could be separated out and whether the individual resistances could be computed. Also different ways of calculating the R_n (noise resistance) and R_sn (spectral noise resistance) parameters were attempted to see which one gave the best comparison with the more standard EIS measurements. The maximum entropy method was recognized to be the most useful for comparison with EIS, as well as for graphic evaluation of results. Regarding distinguishing three areas using different connection arrangements, it was possible to identify the situation when one of the three values was different to the other two. However further experiments are needed before it will be possible to confidently assign an R_n value to each individual area.     

The Impact of Linseed Oil Lipids on the Physical Properties of Corn Crisps and the Possibility of Obtaining Crisps Enriched with n‐3 Fatty Acids

Linseed oil, also known as flaxseed oil, is obtained from the dried, ripened seeds of the flax plant (Linum usitatissimum). The oil is obtained by pressing, sometimes followed by solvent extraction supported by a refining process. Linseed oil is an edible oil that is in demand as a nutritional supplement, as a source of α‐linolenic acid an n‐3 fatty acid. The aim of this work was to investigate: (1) the influence of the corn crisp extrusion process on the degradation of fatty acids in linseed oil (LO) and some preparations obtained from the linseed oil such as ethyl ester (EE) and free fatty acids (FFA) added to the corn in order to increase the nutritional value of the crisps, (2) influence of the oil and two fatty preparations obtained from it on the quality of corn crisps, (3) interaction of the lipid fraction with starch. The extrusion process did not degrade the fatty acids significantly. Expansion ratio obtained in the corn crisp extrusion process decreased from 620 % down to 153 %, the size of pores/thickness of the starch–protein walls forming the structure of the extruded product decreased from 10 μm down to 4 μm, the hardness of the crisps increased from 20 to 75 N, and number of lipid–starch complexes increased with rising polarity of the lipid fraction. FFA were complexed mostly by starch (about 90 %), to a lesser degree by EE (about 60 %) and to the least extent by triacylglycerols (about 10 %). The studies performed under industrial conditions using the single screw extruder for the production of corn crisps with the application of standard parameters of the extrusion process indicated that the addition of a mass of 5 % of the various lipids (triacylglycerols of linseed oil, ethyl esters and fatty acids obtained from linseed oil) to corn grits prior to the extrusion process significantly affect the quality of corn crisps.     

Melt fracture and rheology of linear low density polyethylene ‐ calcium carbonate composites

Rheological behavior and melt fracture of linear low‐density polyethylene (LLDPE) calcium carbonate (CaCO₃) composites were investigated. Two types of commercial inorganic fillers were used, unmodified and modified with stearic acid. Rheological capillary studies were conducted to assess the influence of inorganic filler incorporation as well as chemical treatment on the rheological properties and instability sequence of polyethylene‐based composites. Strong suppression of melt flow instabilities was observed for both types of composites. Mooney analysis was applied to examine the influence of mineral filler addition and stearic acid modification on the wall slip. Moreover, chemical treatment of calcium carbonate allows to obtain better dispersion of the inorganic filler in a polymeric matrix. POLYM. ENG. SCI., 57:998–1004, 2017. © 2016 Society of Plastics Engineers     

The Mechanical Properties of the Novel Nanocrystalline Refractory Tantalum Alloys

Protection of Metals and Physical Chemistry of Surfaces - The nanocrystalline tantalum alloys were investigated in terms of mechanical properties. The materials were obtained by powder metallurgy...     

A New Mechanism of the Selective Photodegradation of Antibiotics in the Catalytic System Containing TiO2 and the Inorganic Cations

The mechanism of sulfisoxazole (SFF) selective removal by photocatalysis in the presence of titanium (IV) oxide (TiO₂) and iron (III) chloride (FeCl₃) was explained and the kinetics and degradation pathways of SFF and other antibiotics were compared. The effects of selected inorganic ions, oxygen conditions, pH, sorption processes and formation of coordination compounds on the photocatalytic process in the presence of TiO₂ were also determined. The Fe³⁺ compounds added to the irradiated sulfonamide (SN) solution underwent surface sorption on TiO₂ particles and act as acceptors of excited electrons. Most likely, the SFF degradation is also intensified by organic radicals or cation organic radicals. These radicals can be initially generated by reaction with electron holes, hydroxyl radicals and as a result of electron transfer mediated by iron ions and then participate in propagation processes. The high sensitivity of SFF to decomposition caused by organic radicals is associated with the steric effect and the high bond polarity of the amide substituent.     

Current Diagnosis and Treatment Options for Cutaneous Adnexal Neoplasms with Follicular Differentiation

Neoplasms derived from follicular tissue are extremely rare. Clinically, they are reported as non-symptomatic, slow-growing nodules. These lesions are mainly benign, but the malignant type can occur. Mainly middle-aged people (50–60 years of age) are affected. These carcinomas are mainly localized on the head and neck or torso. They can be locally aggressive and infiltrate surrounding tissue and metastasize to regional lymph nodes. In the minority of cases, distant metastases are diagnosed. Quick and relevant diagnosis is the basis of a treatment for all types of tumors. The patient’s life expectancy depends on multiple prognostic factors, including the primary tumor size and its mitotic count. Patients should be referred to a specialized skin cancer center to receive optimal multidisciplinary treatment. This article tries to summarize all the information that is currently available about pathogenesis, diagnosis, and treatment methods of follicular tumors.