Frequency shift keyed narrowband interference rejection: optimal exponential weighting factor for the RLS algorithm

Cochannel narrowband interference can limit the performance of direct sequence spread spectrum (DSSS) and high frequency (HF) systems. Narrowband interference (NBI) can be single tone, chirped or frequency shift keyed (FSK) in nature and numerous techniques for its removal have been proposed. Linear adaptive prediction filters based on autoregressive modelling have been suggested owing to their ability to perform in a non-stationary environment. In the FSK narrowband interference case, adaptive filters are susceptible to excess residual errors owing to instantaneous frequency step changes and the finite convergence time required for the filter to adapt to a new interference frequency. The signal degradation owing to this type of interference becomes greater in high SNR regimes and has been found to be a function of the frequency parameters of the FSK interference signal. The paper discusses the convergence and frequency tracking properties of the recursive least squares (RLS) adaptive lattice filter using a posteriori estimation errors in the presence of FSK narrowband interference. An optimal exponential weighting factor that balances convergence time and steady state error is derived for this case of NBI. Results are compared to those of a previously proposed fast converging minimum frequency error (FCMFE) RLS lattice filter.     

The treatment of waste-air containing mixed solvent using a biofilter 2. Treatment of waste-air containing ethanol and toluene in a biofilter

An experiment for five stages of a biofilter-run was performed to investigate the effect of hydrophilic ethanol and hydrophobic toluene on the biodegradation of hydrophobic toluene and hydrophilic ethanol, respectively, when waste-air containing toluene and ethanol was treated by a biofilter. Removal efficiencies of toluene and ethanol began to decrease when inlet load surpassed 90 g/m³/h and 100 g/m³/h consistent with maximum elimination capacities of toluene and ethanol, respectively. At the end of the biofilter-run, removal efficiencies for toluene and ethanol were decreased and maintained at 65% and 40%, respectively. The concentration of toluene at 1st sampling port was raised by factor of two in the 3rd stage of the biofilter run when the inlet load of ethanol co-feed was increased by 1.5 times, while the process conditions of toluene were maintained the same as those of the 2nd stage of biofilter-run. According to the result of Mohseni and Allen, it may be interpreted that removal efficiency of hydrophobic toluene was affected by the presence of hydrophilic ethanol when high load of hydrophobic toluene was applied like that of the 1st sampling port of the biofilter. However it was not the case when a low load of hydrophobic toluene was applied like those of the 2nd, 3rd and 4th sampling ports since hydrophobicity of toluene is much less that of α-pinene. Thus, it may be suggested that biodegradation of hydrophobic VOC was interfered by hydrophilic VOC dissolved in the biolayer and the degree of interference was proportional to the inlet load of hydrophobic VOC as well as that of hydrophilic VOC and was inversely proportional to the solubility of hydrophobic VOC. However, it was inferred that the existence of hydrophobic toluene from waste-air can hardly inversely hinder the removal of hydrophilic ethanol in the biofilter when timeevolutions of hydrophilic ethanol concentrations of this experiment were compared with those of the previous experiment of biofilter to treat waste-air containing ethanol only.     

An investigation into physicochemical characteristics of ash produced from combustion of oil palm biomass wastein a boiler

Ash derived from combustion of Malaysian oil palm biomass (empty fruit bunches consisting of fibers) was physically and chemically characterized in order to provide a comprehensive understanding of its specific properties in terms of toxicity, compositions and reusability. Principal analyses conducted include particle size distribution, scanning electron microscopy, elemental dispersive X-ray, elemental analysis, toxicity characteristic leaching procedure (TCLP) as well as thermogravimetric, X-ray diffractometry and Fourier-transform infrared analyses. TCLP result indicated that the oil palm ash (OPA) should not be classified as toxic wastes in terms of heavy metal leachability since leachable copper, cadmium, lead and nickel concentrations were detected below the stipulated leachability limits. It was determined that the OPA contained high amount of potassium as well as presence of silica which implied its suitability to be reused as crude fertilizer or cement replacement material.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

基于遗传算法的土钉支护结构优化设计研究

通过建立三维有限元模型,对土钉支护的变形和受力性能进行分析,得出土钉力的合理分布。在此基础上,考虑土钉支护的水平位移,采用遗传算法,对土钉支护的结构优化设计进行研究,建立了土钉支护结构的优化设计数学模型,并编制了相应的计算程序。通过算例分析,并与基于极限平衡分析的优化结果相比较,得出合理的土钉支护结构设计的参考结论。     

One-to-Many and Many-to-One Optical Chaos Communications Using Semiconductor Lasers

A theoretical construction of one-to-many (OTM) and many-to-one (MTO) chaos synchronization communications using semiconductor lasers is presented. One center laser provides strong injections (strong link) to other side lasers, and the side lasers also provide weak injections (weak link) to the center one. Simulation results show that the side lasers synchronize with the center laser through injection-locking. In addition, messages transmitted via the strong links or the weak links experience strong chaos pass filtering, enabling us to realize OTM and MTO communications.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.     

Sandwich panels with Kagome lattice cores reinforced by carbon fibers

Stretching dominated Kagome lattices reinforced by carbon fibers were designed and manufactured. The sandwich panels were assembled with bonded laminate skins. The mechanical behaviors of the sandwich panels were tested by out-of-plane compression, in-plane compression and three-point bending. Different failure modes of the sandwich structures were revealed. The experimental results showed that the carbon fiber reinforced lattice grids are much stiffer and stronger than foams and honeycombs. It was found that buckling and debonding dominate the mechanical behavior of the sandwich structures, and that more complaint skin sheets might further improve the overall mechanical performance of the sandwich panels.     

Fast-converging minimum frequency error RLS lattice filter for narrowband interference with discrete frequency steps

This paper discusses the fundamental convergence and frequency tracking properties of the recursive-least-squares (RLS) lattice filter in the presence of narrowband interference (NBI) whose frequency varies in discrete steps. It is shown for filters of this type, that the residual forward energy (RFE) after a frequency transition is a function of the input signal-to-noise ratio (SNR), separation of the sequential frequencies and the filter time constant and is exponentially decaying in nature. Reducing the RFE is important in removing unwanted transient artefacts from the desired signal. The convergence behaviour of the RLS algorithm based on a posteriori estimation errors is analysed under a number of conditions by varying the SNR and frequency step size. In order to limit the impact of the RFE while maintaining a minimum frequency tracking error in steady conditions, a fast-converging minimum frequency error (FCMFE) RLS lattice filter is suggested. For comparison, a least-mean-square (LMS) based gradient-adaptive lattice (GAL) filter is also analysed for this class of narrowband interference.     

Reversible energy recovery logic circuit without non-adiabaticenergy loss

The authors propose a reversible energy recovery logic (RERL) circuit for ultra-low-energy consumption, which consumes only adiabatic energy loss and leakage current loss by completely eliminating non-adiabatic energy loss. It is a dual-rail adiabatic circuit using the concept of reversible logic with a new eight-phase clocking scheme. Simulation results show that at low-speed operation, the RERL consumes much less energy than the complementary static CMOS circuit and other adiabatic logic circuits