Effects of Particle Size on the Fusion of Soda–Lime–Silicate Glass Containing NaCl

The coupled effects of particle size and 1 wt% NaCl additions on the sequence of melting reactions in a multicomponent system (sand–soda ash–calcite–dolomite–feldspar) were studied using data from DTA, DTGA, and XRD interactively. Glass batches varied in average particle size from 250 μm to finer than 45 μm. Milestone events in the fusion process of the coarse particle base glass were elucidated. The termination temperature of the last significant reaction associated with CO₂ release was 35°C lower in the fine particle size batch than with the coarsest batch. Liquid-phase formation at ∼523°C in the batch with 1 wt% NaCl occurred to an increasingly sizable extent with decreasing particle size. This contrasts with a similar effect at ∼630°C for a comparable batch without NaCl via eutectic melting between soda ash and dolomite. Sodium chloride additions significantly enhanced dissolution of CaO relic.     

Surface Chemistry of Lead Titanate and Its Impact on Binder Removal

Carbon residue after binder burnout was characterized for several nonstoichiometric lead titanate powders. Thermal decomposition of the poly(methyl methacrylate) (PMMA) binder was performed in nitrogen at 600°C. A drastic decrease in carbon retention was obtained in the case of the titanium-rich samples. The amount of carbon retention varies from 0.2 mg/m² to 1.2 mg/m² by changing the Pb/Ti molar ratio from 0.92 to 1.08. The surface reaction between PMMA and lead titanate particles was studied by diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS). Surface hydroxyls reacted with ester groups in the PMMA or the methylmethacrylate monomer produced upon pyrolysis. The DRIFTS results showed that titaniumrich samples are less reactive and produce less surfacebound organic groups. Interestingly, titanium-rich samples contained more surface hydroxyls. Isoelectric point measurements, however, show that titanium-rich samples are more acidic. Thus, the reactivity of the surface hydroxyls is determined primarily by their acid-base characteristics rather than their concentration. Lead titanate powder was exposed to MMA vapor in a tube furnace at the indicated temperatures using nitrogen carrier gas as a model experiment. DRIFTS difference spectroscopy and Raman spectroscopy were performed on these samples after the exposure. MMA reacts with lead titanate powder in manner similar to PMMA. Analysis for sp ² and sp ³ absorbance of Raman spectra of these exposed powders at 400°–600°C showed pyrolysis behavior of surface-reacted species. The relative amount of sp ² bonded carbon decreases with increasing exposure temperature.     

Formation of Polymeric Lewis Acid–Lewis Base Complexes with Well-defined Organoboron Polymers

The binding of Lewis bases to organoboron polymeric Lewis acids has been studied and the parameters that determine the complexation equilibrium have been investigated, which include (i) the strength of the individual Lewis acids and Lewis bases, (ii) concentration, and (iii) temperature. While the strongly Lewis acidic borane polymers poly(4-bis(pentafluorophenyl)borylstyrene) (PS-BPf) and poly(4-(di-2-thienylboryl)styrene) (PS-BTh) form isolable complexes with strong Lewis bases such as 4-t-butylpyridine (^tPy), a temperature dependent equilibrium is established with weaker bases such as THF. Similarly, the weakly Lewis acidic boronate polymer poly(4-diethoxyborylstyrene) (PS-BOEt) undergoes a temperature dependent equilibrium with the strong Lewis base 4-dimethylaminopyridine (DMAP), while poly(4-pinacolatoborylstyrene) (PS-BPin) does not significantly bind to pyridine bases. Decomplexation of PS-BTh· ^t Py is achieved by treatment with the stronger Lewis acid, B(C₆F₅)₃, thereby confirming the reversible nature of the polymeric Lewis acid–base adducts. This paper is dedicated to Professor Ian Manners in gratitude of his guidance throughout the years and recognition of his scientific accomplishments     

Sterol metabolism in the opportunistic pathogen <Emphasis Type="Italic">Pneumocystis</Emphasis>: Advances and new insights

Pneumocystis can transiently colonize healthy individuals without causing adverse symptoms, and most people test positive for exposure to this organism early in life. However, it can cause Pneumocystis pneumonia (PcP) in people with impaired immune systems and is a major cause of death in HIV/AIDS. Although it has close affinities to the Ascomycetes, Pneumocystis has features unlike those of any single group of fungi. For example, Pneumocystis does not synthesize ergosterol, which is consistent with the inefficacy of amphotericin B and some triazoles in clearing PcP. Pneumocystis sterols include distinct Δ⁷ 24-alkylsterols. Metabolic radiolabeling experiments demonstrated that P. carinii synthesizes sterols de novo. Cholesterol is the most abundant sterol in Pneumocystis; most, if not all, is scavenged from the mammalian host lung by the pathogen. The P. carinii erg7, erg6, and erg11 genes have been cloned, sequenced, and expressed in heterologous systems. The recombinant P. carinii S-adenosyl-l-methionine:C-24 sterol methyl transferase (SAM:SMT) has a preference for lanosterol over zymosterol as substrate, and the enzyme can catalyze the transfer of either one or two methyl groups to the C-24 position of the sterol side chain. Two different sterol compositions were detected among human-derived P. jirovecii; one was dominated by C₂₈ and C₂₉ sterols, and the other had high proportions of higher molecular mass components, notably the C₃₂ sterol pneumocysterol. The latter phenotype apparently represents organisms blocked at 14α-demethylation of the sterol nucleus. These studies suggest that SAM:SMT is an attractive drug target for developing new chemotherapy for PcP.     

Autoxidation of saturated fatty acids. II. The determination of the site of hydroperoxide groups in autoxidizing methyl palmitate

The monohydroperoxides of methyl palmitate oxidized at 150C were concentrated, purified, and reduced to yield a mixture of isomers of monohydroxy palmitate. No evidence of unsaturation in these molecules could be obtained, and no direct method for the resolution or identification of the individual isomers was found. Nuclear magnetic resonance (NMR) spectroscopy of the reduced esters suggested that the hydroxy groups were not located at either end of the chain of the fatty ester. To establish the location of the initial oxidative attack on saturated esters, the reduced esters of oxidized methyl palmitate were chemically cleaved at the location of the hydroxy group by means of chromium trioxide oxidation and by the Beckmann transformation. The resulting mono- and dibasic fatty acids were methylated and analyzed by gas chromatography. This analysis indicated that the oxidation of methyl palmitate did not occur selectively at one location along the ester. Although all carbon atoms can apparently be oxidized, preferential oxidation was observed toward the center of the molecule.     

Mass determination of the fatty acids released from tannin-stimulated rabbit alveolar macrophages

Previous studies with macrophages that had been prelabeled with [¹⁴C]arachidonic acid (20∶4) have shown that condensed tannin is a potent agonist for the release of arachidonic acid. However, it has not been demonstrated that the percentage release of [¹⁴C]20∶4 accurately reflects the metabolic activity of the endogenous 20∶4 pool. In order to measure the 20∶4 mass release relative to the total cellular 20∶4 pool, the free fatty acids of freshly isolated alveolar macrophages were derivatized with a fluorescent reagent, and then separated and quantified by high-performance liquid chromatography. The amounts of esterified fatty acids were measured by gas chromatography of the methyl esters. Free fatty acid levels were compared to those of the total esterified plus unesterified fatty acids to determine the actual percentage released of each fatty acid. Tannin-stimulated release of 20∶4 mass reflected that previously reported for the release of [¹⁴C]20∶4 label but at a slower rate and at a much lower percentage indicating that [¹⁴C]20∶4 had been incorporated into part of a more reactive pool. The specificity of the fatty acid release induced by tannin and β-1,3-glucan, a known agonist for 20∶4 release, was also examined. Both agonists promoted an increase in the levels of free 20∶4 and of other fatty acids. A comparison of the absolute increases of each of the fatty acids indicated that tannin caused a preferential increase in the mass of free 20∶4, whereas β-1,3-glucan evoked a selective increase in the mass of 16∶0. Deceased.     

Activated gas plasma surface treatment of polymers for adhesive bonding

Polyethylene, polypropylene, poly(vinyl fluoride) (Tedlar), polystyrene, nylon 6, poly(ethylene terephthalate) (Mylar), polycarbonate, cellulose acetate butyrate, and a poly(oxymethylene) copolymer were treated with activated helium and with activated oxygen. Mechanical strengths of adhesive-bonded specimens prepared from treated and from untreated coupons were compared. Polyethylene (PE) and polypropylene (PP) showed the greatest increases in bond strength. Oxygen and helium were both effective with polyethylene, but polypropylene showed no improvement when treated with activated helium. The results with excited helium parallel the effects of ionizing radiation on these two polymers, as does the appearance of unsaturation bands in the infrared (965 cm^?1 in PE, and 887 and 910 cm^?1 in PP). Active nitrogen produced excellent bond strength with polyethylene but not with polypropylene. Of the remaining polymers examined, Tedlar, polystyrene, and nylon 6 showed the greatest improvement in bondability after treatment, and Mylar showed moderate improvement. Polycarbonate, cellulose acetate butyrate, and the poly(oxymethylene) copolymer gave approximately two-fold increases in lap-shear bond strength. In several cases, significant differences in response to time of treatment and type of excited gas were found.     

Cycling hardening and serration yielding of Fe-Ni-Cr alloy at high temperature under out-phase TMF

Behaviour of hardening and serration yield of a Fe-Ni-Cr alloy under isothermal cycling (ISC) and out-phase TMF was studied on the basis of varied hysteresis loops. Cycling hardening and serrated yielding for ISC depend on the temperature and the total strain range, stronger hardening with serrated yielding at higher strain range under ISC at 600 °C, but no hardening and serrated yielding occurred under ISC at 800 °C. Stronger hardening with stress serration occurred at the thermal path going to the lowest temperature, no stress serration occurred at the highest temperature under the out-phase. The hardening also depends on the total strain range, higher total strain range with lower cycling temperature resulted in a stronger hardening and remarkable serration yielding behavior. Weaker hardening without serrated yielding occurred at near 800 °C may due to an obvious cycling stress drop under out-phase TMF. Change in the shape of the hysteresis loops also expresses the degree of the damage of the tested alloy under out-phase and ISC.     

Fabrication and characterization of nano silver powder prepared by spray pyrolysis

Silver powder was fabricated by spray pyrolysis, using 2%–20% AgNO₃ solution, 336–500 mL/h flux of AgNO₃ solution, 0.28–0.32 MPa flux of carrier gas and in the 620–820 °C temperature range. The effects of furnace set temperature, concentration of AgNO₃ aqueous solution, flux of AgNO₃ aqueous solution as well as carrier gas on the morphology and particle size distribution of silver powder, were investigated. The experimental results showed that with the high concentration of AgNO₃ aqueous solution, the average grain size of silver decreased with the increasing of furnace set temperature. But the gain size distribution was not homogenous, the discontinuous grain growth occurred. With the low concentration of AgNO₃ aqueous solution, the higher furnace set temperature made the nano sliver grains sintered together to grow. Nano silver powder about 100 nm was fabricated by spray pyrolysis, using 2wt% AgNO₃ solutions, 336 mL/h flux of AgNO₃ aqueous solution, 0.32 MPa flux of carrier gas at 720 °C furnace set temperature.