GaSb and InAs: New Materials for Metal-Semiconductor Point-Contact Diodes

Metal-semiconductor point contact diodes have proved to be good detectors and mixers for radiation from the far-infrared to visible. Until now GaAs, InSb and InP are the most studied and used semiconductor materials for these devices. In this work we present the performance in the visible and infrared region for metal-semiconductor point-contact diodes with GaSb or InAs as the semiconductor layers. These two new materials have shown good characteristics.     

Provisioning of dynamic traffic in mixed-line-rate optical networks with launch power determination

In mixed-line-rate (MLR) networks, different line rates on different wavelengths can coexist on the same fiber. MLR architectures can be built over transparent optical networks, where the transmitted signals remain in the optical domain along the entire path. Along the transparent optical path, a signal experiences various physical layer impairments (PLIs), and its quality degrades as it travels through each optical component. One of the major factors that affect the transmission quality is the launch power of the optical signal. The power must be large enough to ensure noise resiliency at the receiver, but it must be below the limit where fiber nonlinearities distort the signal. Moreover, high launch power is disruptive not only for the actual lightpath itself but also for neighboring lightpaths, and this effect is particularly critical in MLR networks since advanced modulation techniques used for high line rates are highly susceptible to PLIs. In this study, we investigate the problem of determining the appropriate launch power for provisioning of dynamic connection requests in MLR networks. By setting the appropriate launch power for each connection, we aim to maximize the number of established connections. We propose two different heuristics to determine the appropriate launch power of a lightpath. Worst-case best-case average (WBA) is based on optical reach of signal in a transparent optical network. In impairment-aware launch power determination (I-ALPD), current state of the network and impairments are evaluated to determine the launch power. The proposed approaches are practical and can adapt to the needs of network operators. Simulation results show that the performances of the proposed approaches show better results than the existing schemes in terms of blocking probability and bandwidth blocking ratio.     

Recent Advances on High-Speed and Holographic Two-Photon Direct Laser Writing

Two-Photon Lithography, thanks to its very high sub-diffraction resolution, has become the lithographic technique par excellence in applications requiring small feature sizes and complex 3D pattering. Despite this, the fabrication times required for extended structures remain much longer than those of other competing techniques (UV mask lithography, nanoimprinting, etc.). Its low throughput prevents its wide adoption in industrial applications. To increase it, over the years different solutions have been proposed, although their usage is difficult to generalize and may be limited depending on the specific application. A promising strategy to further increase the throughput of Two-Photon Lithography, opening a concrete window for its adoption in industry, lies in its combination with holography approaches: in this way it is possible to generate dozens of foci from a single laser beam, thus parallelizing the fabrication of periodic structures, or to engineer the intensity distribution on the writing plane in a complex way, obtaining 3D microstructures with a single exposure. Here, the fundamental concepts behind high-speed Two-Photon Lithography and its combination with holography are discussed, and the literary production of recent years that exploits such techniques is reviewed, and contextualized according to the topic covered.     

Reaching the Fundamental Limitation in CO2 Reduction to CO with Single Atom Catalysts

The electrochemical CO₂ reduction reaction (CO₂RR) to value-added chemicals with renewable electricity is a promising method to decarbonize parts of the chemical industry. Recently, single metal atoms in nitrogen-doped carbon (MNC) have emerged as potential electrocatalysts for CO₂RR to CO with high activity and faradaic efficiency, although the reaction limitation for CO₂RR to CO is unclear. To understand the comparison of intrinsic activity of different MNCs, two catalysts are synthesized through a decoupled two-step synthesis approach of high temperature pyrolysis and low temperature metalation (Fe or Ni). The highly meso-porous structure results in the highest reported electrochemical active site utilization based on in situ nitrite stripping; up to 59±6% for NiNC. Ex situ X-ray absorption spectroscopy (XAS) confirms the penta-coordinated nature of the active sites. The catalysts are amongst the most active in the literature for CO₂ reduction to CO. The density functional theory calculations (DFT) show that their binding to the reaction intermediates approximates to that of Au surfaces. However, it is found that the turnover frequencies (TOFs) of the most active catalysts for CO evolution converge, suggesting a fundamental ceiling to the catalytic rates.     

Zr‐Doped Indium Oxide (IZRO) Transparent Electrodes for Perovskite‐Based Tandem Solar Cells

Parasitic absorption in transparent electrodes is one of the main roadblocks to enabling power conversion efficiencies (PCEs) for perovskite‐based tandem solar cells beyond 30%. To reduce such losses and maximize light coupling, the broadband transparency of such electrodes should be improved, especially at the front of the device. Here, the excellent properties of Zr‐doped indium oxide (IZRO) transparent electrodes for such applications, with improved near‐infrared (NIR) response, compared to conventional tin‐doped indium oxide (ITO) electrodes, are shown. Optimized IZRO films feature a very high electron mobility (up to ≈77 cm² V^?1 s^?1), enabling highly infrared transparent films with a very low sheet resistance (≈18 Ω □^?1 for annealed 100 nm films). For devices, this translates in a parasitic absorption of only ≈5% for IZRO within the solar spectrum (250–2500 nm range), to be compared with ≈10% for commercial ITO. Fundamentally, it is found that the high conductivity of annealed IZRO films is directly linked to promoted crystallinity of the indium oxide (In₂O₃) films due to Zr‐doping. Overall, on a four‐terminal perovskite/silicon tandem device level, an absolute 3.5 mA cm^?2 short‐circuit current improvement in silicon bottom cells is obtained by replacing commercial ITO electrodes with IZRO, resulting in improving the PCE from 23.3% to 26.2%.     

From irradiance to output power fluctuations: the PV plant as a low pass filter

The power generated by large grid‐connected photovoltaic (PV) plants depends greatly on the solar irradiance. This paper studies the effects of the solar irradiance variability analyzing experimental 1‐s data collected throughout a year at six PV plants, totaling 18 MWp. Each PV plant was modeled as a first order filter function based on an analysis in the frequency domain of the irradiance data and the output power signals. An empiric expression which relates the filter parameters and the PV plant size has been proposed. This simple model has been successfully validated precisely determining the daily maximum output power fluctuation from incident irradiance measurements. Copyright © 2011 John Wiley & Sons, Ltd.     

Characterization and exploitation of heterogeneous OFDM primary users in cognitive radio networks

The fundamental features of cognitive radio (CR) systems are their ability to adapt to the wireless environment where they operate and their opportunistic occupation of the licensed spectrum bands assigned to the primary network. CR users in CR systems should not cause any interference to primary users (PUs) of the primary network. For this purpose, CR users need to accurately estimate the features and activities of the primary users. In this paper, a novel characterization of heterogeneous PUs and a novel reconfigurability solution in CR networks are introduced. The characterization of PUs consists of a detector and classifier that distinguishes between heterogenous PUs. The PU characteristics stored in radio environmental maps are utilized by an interference/throughput adapter for the optimization of CR parameters. The performance of the proposed solutions is evaluated by showing false alarm and missed detection probabilities of the detector/classifier in a multipath fading channel with additive white Gaussian noise. Moreover, the impact of the PU characteristics on the CR throughput is analyzed.     

Security and delay issues in SIP systems

The deployment of multimedia over IP (MoIP), and in particular voice over IP services, requires to solve new security issues they introduce, before completely exploiting the great opportunities they offer to telecommunication market. Furthermore, the implementation of various security measures can cause a marked deterioration in quality of service, which is fundamental to the operation of an MoIP network that meets users' quality expectations. In particular, because of the time‐critical nature of MoIP and its low tolerance for disruption and packet loss, many security measures implemented in traditional data networks are simply not applicable in their current form. This paper presents an analysis of the security options of Session Initiation Protocol‐ (SIP)‐based MoIP architecture aimed at evaluating their impact on delay. In particular, each security option is analyzed in terms of clock cycles needed to perform the related operations. This parameter could be used to estimate the delay introduced by the security mechanisms. Moreover the paper proposes a rigorous definition of five security profiles, which provide different levels of security to a MoIP system. Copyright © 2009 John Wiley & Sons, Ltd.     

Densification of Oxide Nanoparticle Thin Films by Irradiation with Visible Light

A technique is presented that allows for altering of the physical characteristics of films of TiO₂ nanoparticles by exposure to visible light. In this technique, dye‐sensitized oxide nanoparticles are deposited on a substrate by dip‐coating. Photodissociation of the organic ligand layer leads to cross‐linking of the nanoparticles. Consequently, irradiated films have a decreased porosity, an increased index of refraction and an increased hydrophobicity. Films irradiated with green light are compared to films irradiated with UV light. Within experimental error, visible‐ and UV‐illumination induces the same changes in the films. The mechanism of surfactant elimination in dye‐sensitized oxide particles is discussed, patterning is demonstrated, and prospective applications of the technique are considered.