Stability and electronic properties of armchair boron nitride/carbon nanotubes

In this work are studied the electronic and structural properties of armchair boron nitride/carbon nanotubes using first principles calculations. The density functional within the generalized gradient approximation (HSEh1PBE-GGA) is used. For each composition, different bonding schemes for the construction of the hybrid systems were employed. Among them, structural stability with neutral charge was determined for the following compositions: T1: B₄₀N₃₅C₇₅H₂₀, T2: B₃₅N₄₀C₇₅H₂₀, T3: B₃₇N₃₈C₇₅H₂₀, T4 : B₃₇N₃₇C₇₆H₂₀, and T7: B₃₅N₃₅C₈₀H₂₀. All these hybrid nanotubes have high polarity; the T3, T4 and T7 are semiconductors: whereas T1 and T2 are conductor in character. The formers also have magnetic behavior. These properties together with a low-chemical potential suggest applications as nano-vehicle for drug delivery. These mixed nanotubes also have potential applications in the electronic devices based on the small work function.     

Photocatalytic activity of a new composite material of Fe (III) oxide nanoparticles wrapped by a matrix of polymeric carbon nitride and amorphous carbon

Polymeric carbon nitride was synthesized from urea and doped with Cu and Fe to act as co-catalysts. The material doped with Fe was a new composite material composed of Fe(III) oxides (acting as a co-catalyst) wrapped by the polymer layers and amorphous carbon. Furthermore, the copper doped material was described in a previous report. The photocatalytic degradation of the azo dye direct blue 1 (DB) was studied using as photocatalysts: pure carbon nitride (CN), carbon nitride doped with Cu (CN-Cu) and carbon nitride doped with Fe (CN-Fe). The catalysts were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), by X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller method (BET), etc. The adsorption phenomenon was studied using the Langmuir and Freundlich models. For the kinetic study, a solution of 500 mg L^?1 of DB1 was treated with each catalyst, visible light and H₂O₂. The dye concentration was measured by spectrophotometry at the wavelength of 565 nm, and the removal of the total organic content (TOC) was quantified. BET analysis yielded surface areas of 60.029, 20.116 and 70.662 m²g^?1 for CN, CN-Cu and CN-Fe, respectively. The kinetics of degradation were pseudo-first order, whose constants were 0.093, 0.039 and 0.110 min^?1 for CN, CN-Cu and CN-Fe, respectively. The total organic carbon (TOC) removal reached the highest value of 14.46% with CN-Fe.     

Utilizing Iron's Attractive Chemical and Magnetic Properties in Microrocket Design,Extended Motion,and Unique Performance

All‐in‐one material for microrocket propulsion featuring acid‐based bubble generation and magnetic guidance is presented. Electrochemically deposited iron serves as both a propellant, toward highly efficient self‐propulsion in acidic environments, and as a magnetic component enabling complete motion control. The new microrockets display longer lifetime and higher propulsion efficiency compared to previously reported active metal zinc‐based microrockets due to the chemical properties of iron and the unique structure of the microrockets. These iron‐based microrockets also demonstrate unique and attractive cargo towing and autonomous release capabilities. The latter is realized upon loss of the magnetic properties due to acid‐driven iron dissolution. More interestingly, these bubble‐propelled microrockets assemble via magnetic interactions into a variety of complex configurations and train structures, which enrich the behavior of micromachines. Modeling of the magnetic forces during the microrocket assembly and cargo capture confirms these unique experimentally observed assembly and cargo‐towing behaviors. These findings provide a new concept of blending propellant and magnetic components into one, toward simplifying the design and fabrication of artificial micro/nanomachines, realizing new functions and capabilities for a variety of future applications.     

Hybrid Nanoscopy of Hybrid Nanomaterials

The combination of complementary techniques to characterize materials at the nanoscale is crucial to gain a more complete picture of their structure, a key step to design and fabricate new materials with improved properties and diverse functions. Here it is shown that correlative atomic force microscopy (AFM) and localization‐based super‐resolution microscopy is a useful tool that provides insight into the structure and emissive properties of fluorescent β‐lactoglobulin (βLG) amyloid‐like fibrils. These hybrid materials are made by functionalization of βLG with organic fluorophores and quantum dots, the latter being relevant for the production of 1D inorganic nanostructures templated by self‐assembling peptides. Simultaneous functionalization of βLG fibers by QD655 and QD525 allows for correlative AFM and two‐color super‐resolution fluorescence imaging of these hybrid materials. These experiments allow the combination of information about the topography and number of filaments that compose a fibril, as well as the emissive properties and nanoscale spatial distribution of the attached fluorophores. This study represents an important step forward in the characterization of multifunctionalized hybrid materials, a key challenge in nanoscience.     

Use of 3D printing for biofuel production: efficient catalyst for sustainable biodiesel production from wastes

This work deals with the sustainable biodiesel production from low-cost renewable feedstock (waste and non-edible oils) using a heterogeneous catalyst constituted by potassium loaded on an amorphous aluminum silicate naturally occurring as volcanic material (pumice). The main challenge to biodiesel production from low-quality oils (used oils and greases) is the high percentage of free fatty acids (FFAs) and water in the feedstock that causes undesirable side reactions. The catalytic materials studied were tested in the transesterification reaction when using low-quality oils containing a high proportion of free fatty acids (FFAs) and water. Results indicated that the amount of acid and basic sites on the catalytic surface increases upon increasing potassium loading in the catalyst, displaying better performance for biodiesel production. Indeed, the modification of the aluminum silicate substrate upon potassium incorporation results in a catalytic material containing both acidic and basic sites, which are responsible for both triglycerides transesterification and FFA esterification reactions. The studied catalyst not only showed good performance in the biodiesel production reaction but also good tolerance to FFA and water contained in the feedstock for biodiesel production. The catalytic material was microstructured by 3D printing in order to design a catalytic stirring system with high mechanical strength, efficient and reusable. The use of 3D printing in biofuel production is a novelty that brings good solutions for catalyst production.     

How can Cleaner Production practices contribute to meet ISO 14001 requirements? Critical analysis from a survey with industrial companies

The companies’ needs to adopt changes in their way of production to maximize the environmental performance required by their stakeholders, and at the same time, to maximize their economic and market performance, have made them seek for environmental strategies and certifications. In this sense, the Cleaner Production and the Environmental Management System based on ISO 14001 have been, respectively, presented, since the main objective of this research is to identify and analyze Cleaner Production contributions to comply with ISO 14001 requirements. For such, a survey research has been carried out in Brazilian industrial companies certified by ISO 14001. We have identified the main performance factors by leading practices and variables of Cleaner Production that contribute to the compliance with the standard requirements by companies. Thus, it has been noted that Cleaner Production is an important strategy for the preparation of companies for certification as well as for improving their environmental performance.     

Incorporating linear programing and life cycle thinking into environmental sustainability decision-making: a case study on anchovy canning industry

Life cycle assessment (LCA) is a powerful tool to support environmental informed decisions among product and process alternatives. LCA results reflect the process stage contributions to several environmental impacts, which should be made mutually comparable to help in the decision-making process. Aggregated environmental indexes enable the translation of this set of metrics into a one final score, by defining the attached weights to impacts. Weighting values reflect the corresponding relevance assigned to each environmental impact. Current weighing schemes are based on pre-articulation of preferences, without considering the specific features of the system under study. This paper presents a methodology that combines LCA methodology and linear programming optimisation to determine the environmental improvement actions that conduct to a more sustainable production. LCA was applied using the environmental sustainability assessment methodology to obtain two main indexes: natural resources (NR) and environmental burdens (EB). Normalised indexes were optimised to determine the optimal joint of weighting factors that lead to an optimised global Environmental Sustainability Index. The proposed methodology was applied to a food sector, in particular, to the anchovy canning industry in Cantabria Region (Northern Spain). By maximising the objective function composed of NR and EB variables, it is possible to find the optimal joint of weights that identify the best environmental sustainable options. This study proves that LCA can be applied in combination with linear programing tools as a part of the decision-making process in the development of more sustainable processes and products.     

3D Orientational Control in Self‐Assembled Thin Films with Sub‐5 nm Features by Light

While self‐assembled molecular building blocks could lead to many next‐generation functional organic nanomaterials, control over the thin‐film morphologies to yield monolithic sub‐5 nm patterns with 3D orientational control at macroscopic length scales remains a grand challenge. A series of photoresponsive hybrid oligo(dimethylsiloxane) liquid crystals that form periodic cylindrical nanostructures with periodicities between 3.8 and 5.1 nm is studied. The liquid crystals can be aligned in‐plane by exposure to actinic linearly polarized light and out‐of‐plane by exposure to actinic unpolarized light. The photoalignment is most efficient when performed just under the clearing point of the liquid crystal, at which the cylindrical nanostructures are reoriented within minutes. These results allow the generation of highly ordered sub‐5 nm patterns in thin films at macroscopic length scales, with control over the orientation in a noncontact fashion.