Performance evaluation of anti-radiation based on the gamma degradation process

In the environment of space radiation, the high-energy charged particles or high-energy photons acting on a spacecraft can cause either temporary device degradation or permanent failure. The traditional probability model is difficult to obtain reliable estimation of unit radiation resistance performance with small samples. Considering that different products will change differently after high-energy particle radiation, we construct a model based on the gamma degradation process. This model can efficiently describe the law of unit radiation resistance variation with the total radiation dose levels under the effect of the total dose and displacement damage. Finally, the proposed model is used to assess the anti-radiation performance of the N-channel power MOSFET device STRH60N20FSY3 produced by STM to obtain average unit radiation resistance, survival probability, survival function, etc.     

Effect of ambient wind on pressure wave generated by high-speed train entering a tunnel

Journal of Central South University - Using three-dimensional, unsteady N-S equations and k-ε turbulence model, the effect of ambient wind on the pressure wave generated by a high-speed train...     

Improved Computational Model of Grid Cells Based on Column Structure

To simulate the firing pattern of biological grid cells, this paper presents an improved computational model of grid cells based on column structure. In this model, the displacement along different directions is processed by modulus operation, and the obtained remainder is associated with firing rate of grid cell. Compared with the original model, the improved parts include that: the base of modulus operation is changed, and the firing rate in firing field is encoded by Gaussian-like function. Simulation validates that the firing pattern generated by the improved computational model is more consistent with biological characteristic than original model. Besides, the firing pattern is badly influenced by the cumulative positioning error, but the computational model can also generate the regularly hexagonal firing pattern when the real-time positioning results are modified.     

高分2号图像业务化大气校正查找表的设计与实现

为实现高分2号图像(GF2)业务化大气校正,利用矢量6S模型(6SV)将辐射传输散射与吸收进行分离计算,其中散射部分采用涵盖各种大气模式、气溶胶类型、成像几何等条件下的大气校正查找表(look-up tables,LUTs)表示,大气吸收部分采用6SV拟合计算的6种大气模式下大气透过率的经验公式表示,这种处理有效简化了查找表大小.在内存4 GB、主频3.10 GHz条件下,通过比较基于本查找表方法和基于FLAASH大气校正软件对北京地区一景GF2数据处理.结果表明:以6SV模型直接大气校正法结果作为真值,两者的绝对误差分别为0.8%和2.6%,处理时间分别为77 s和240 s,该大气校正查找表在处理精度和效率更加适合业务化大气校正.     

Aerodynamic performance analysis of trains on slope topography under crosswinds

This work used the computational fluid dynamics method combined with full-scale train tests to analyze the train aerodynamic performance on special slope topography. Results show that with the increment in the slope gradient, the aerodynamic forces and moment increase sharply. Compared with the flat ground condition, the lateral force, lift force, and overturning moment of the train on the first line increase by 153.2%, 53.4% and 124.7%, respectively, under the slope gradient of 20°. However, with the increment of the windward side's depth, the windbreak effect is improved obviously. When the depth is equal to 10 m, compared with the 0 m, the lateral force, lift force and overturning moment of the train on the first line decrease by 70.9%, 77.0% and 70.6%,respectively. Through analyzing the influence of slope parameters on the aerodynamic performance of the train, the relationships among them are established. All these will provide a basic reference for enhancing train aerodynamic performances under different slope conditions and achieve reasonable train speeds for the operation safety in different wind environments.     

层间接触状态和横向力大小对车辙贡献率的影响

车辙贡献率是反映沥青路面各结构层车辙病害程度的一个主要参数,可用于指导沥青路面的设计和施工.利用三维有限元计算软件建立三维有限元模型用于理论分析,将有限元计算结果与理论解进行对比,验证了该三维有限元模型的可靠性.采用实测的轮胎接地压力,考虑不同层间接触状态和横向力大小,结合有限元计算的数据,分析了沥青路面结构层的车辙贡献率.结果表明:在层间完全连续状态下,横向力大小的选取不能简单地选取最大垂直轮胎接地压力的一定比例,而是要根据所研究的具体情况具体分析.在对沥青路面车辙贡献率的研究中,可以忽略层间接触状态,即假定层间完全连续.     

Weathering modification of acrylic emulsion by introducing UV absorbing groups

A new kind of UV-absorbing silicon-fluorinated acrylic emulsion was prepared by emulsion polymerization with 4-allyloxy-2-hydroxybenzophenone, 3-methacryloxypropyltrimethoxysilane (MPS) and hexafluorobutyl methacrylate (HFMA) as functional monomers. The emulsion and its coating were characterized by transmission electron microscope, Fourier transform infrared spectrum (FTIR), X-ray photoelectron spectroscopy, ultraviolet absorption spectrum,thermo-gravimetric analysis, water contact angle (CA), and artificial accelerated aging test. The results indicated that the emulsion with core-shell structure was synthesized and showed prominent absorption peaks at 320 and 350 nm. The water CA of the coating was increased from 70.2° to 86.7° because of the incorporated HFMAs and MPSs. Both of the initial and final decomposition temperatures of the coating were increased by more than 20°C compared with those of the unmodified coating. After 10 days of accelerated aging, the color difference (ΔE) and rate of loss of gloss (ΔG) were only 2.78% and 5.22%, while those of the unmodified coating were as high as 22.94% and 78.57%, respectively. Because of the UV absorbers were incorporated by chemical reaction, the new coating had a more durable and effective anti-ultraviolet performance compared with the coatings the UV absorbers were introduced by physical blending.     

中国的稀有金属

本文简要介绍了中国稀有金属在研究、生产方面的发展概况。     

Accelerated electrospark deposition and the wear behavior of coatings

Electrospark deposition (ESD) is a coating process that is featured by low heat input to the substrate. Low coating efficiency and other limitations influence its wider application. The present paper introduces newly designed ESD equipment, by which a higher coating rate can be reached. The relationship among coating thickness, surface roughness, and process parameters such as pulse energy, pulse frequency, and deposition time are presented. Electrospark deposition coating by the new equipment on AISI 1045 steel (with WC-8% Co as electrode) increases the wear resistance by 5 to 8 times. The micromechanism is investigated by scanning electron microscopy observation.     

用双层辉光等离子法在钛表面制备的Ti-Pd合金层性能研究

采用双层辉光等离子冶金技术在纯钛表面制备了Ti—Pd合金层。其深度大约为90μm，Pd含量呈梯度变化，并出现了TiPd3，TiPd2，Ti2Pd3，Ti3Pd5，TiPd，Ti4Pd等6种化合物相和Pd相。合金层在100℃的NaCl饱和溶液＋HCl溶液以及40℃的8．6％H2SO4溶液中的耐缝隙腐蚀性能优于Ti0．2Pd合金；在室温80％H2SO4的溶液中，腐蚀速率仅为0．682mm／a，是Ti0．2Pd合金的18．2％：在室温30％HCl的溶液中，表面Ti—Pd的腐蚀速率仅为0．004mm／a，是Ti0．2Pd合金的12．5％。