Synchronal measurement of flow structure and heat transfer of impingement jet

This paper will present the characteristics of flow behavior and thermal field of both free and
impingement jet issued from a circular orifice nozzle at Re=8900.The flow behavior of a single round
jet and impingement jet was observed by smoke flow visualization recorded by a high speed camera
using 5000 frame per second.Heat transfer coefficient on the impingement surface was measured by
means of infrared camera （TVS-8500,Avio） with a two-dimensional array of Indeum-Antimony （In Sb）
sensors varying in the separation distance between the nozzle and the target plate.The heat transfer
coefficient changes in time and spatial.Therefore,the root mean square distribution of the heat
transfer was obtained from the data.As a result,it was confirmed that the longitudinal vortex was
observed outside of the ring vortex,and then the longitudinal vortex was penetrated in the jet
flow.Moreover,the high value of root mean square of the heat transfer coefficient has spread radially
in stripy manner,which is caused as the results of the longitudinal vortexes flowing in the radial
direction on the impingement plate.     

Germanium recovery using polyphenol microspheres prepared by horseradish peroxidase reaction

BACKGROUND: The formation of polyphenol microspheres by the polymerization of 3‐methylcatechol was performed in a methanol/phosphate buffer solution using horseradish peroxidase (HRP), without the use of a surfactant or a water/oil interface, to be used for germanium recovery. RESULTS: The polyphenol microspheres were of diameter 1 mm. The functional group density of phenol group in the polymer was approximately 15 mol kg^?1 determined by the Folin‐Denis method. In batchwise experiments, the amount of germanium adsorbed was 0.23 mol kg^?1. CONCLUSION: Because germanium is a rare metal, a system for its recovery is required. Using the proposed system, continuous recovery of germanium can be achieved using multilayered microspheres. Copyright © 2011 Society of Chemical Industry     

Fretting fatigue behaviour of Ni-free high-nitrogen stainless steel in a simulated body fluid

Abstract

Fretting fatigue behaviour of Ni-free high-nitrogen steel (HNS) with a yield strength of about 800 MPa, which was prepared by nitrogen gas pressurized electroslag remelting, was studied in air and in phosphate-buffered saline (PBS(-)). For comparison, fretting fatigue behaviour of cold-rolled SUS316L steel (SUS316L(CR)) with similar yield strength was examined. The plain fatigue limit of HNS was slightly lower than that of SUS316L(CR) although the former had a higher tensile strength than the latter. The fretting fatigue limit of HNS was higher than that of SUS316L(CR) both in air and in PBS(-). A decrease in fatigue limit of HNS by fretting was significantly smaller than that of SUS316L(CR) in both environments, indicating that HNS has better fretting fatigue resistance than SUS316L(CR). The decrease in fatigue limit by fretting is discussed taking into account the effect of friction stress due to fretting and the additional influences of wear, tribocorrosion and plastic deformation in the fretted area.     

A hybrid model for a multiproduct pipeline planning and scheduling problem

Brazilian petrobras is one of the world largest oil companies. Recurrently, it faces a very difficult planning and scheduling problem: how to operate a large pipeline network in order to adequately transport oil derivatives and biofuels from refineries to local markets. In spite of being more economical and environmentally safer, the use of a complex pipeline network poses serious operational difficulties related to resource allocation and temporal constraints. The current approaches known from the literature only consider a few types of constraints and restricted topologies, hence they are far from being applicable to real instances from petrobras. We propose a hybrid framework based on a two-phase problem decomposition strategy. A novel Constraint Programming (CP) model plays a key role in modelling operational constraints that are usually overlooked in literature, but that are essential in order to guarantee viable solutions. The full strategy was implemented and produced very adequate results when tested over large real instances.     

Long-term trends of electric efficiencies in electricity generation in developing countries

This analysis provides time-series data on electric efficiencies for 138 countries and regions, covering all fossil fuels for the period 1971–2005, with an emphasis on non-Organization for Economic Cooperation and Development (OECD) countries. Fossil fuel consumption for electricity generation in non-OECD countries now exceeds that in the OECD. The historical performance of the top five non-OECD consumers of each fossil fuel for which reliable data are available is presented and discussed. For each fuel, the countries that lead the world in efficiency are used for benchmarks; bringing the rest of the world up to these standards would result in energy savings of 26 EJ (equivalent to 5% of global energy consumption) and CO₂ emissions reduction of 2.1 Pg (equivalent to 8% of global CO₂ emissions). Coal showed the largest potential margin of improvement for both energy and CO₂, with possible savings equivalent to 3% of current global energy consumption and 5% of global CO₂ emissions. The gap in electric efficiency between OECD and non-OECD countries over the past 35 years has widened for coal-fired generation, stayed relatively constant for natural gas, but has shrunk for petroleum. The results show the very gradual nature of overall efficiency improvements and the significant differences among regions and countries.     

Evaluation of selective plating media for the detection of heat- or freeze-injured Staphylococcus aureus

The efficacy of Baird-Parker (BP) agar, mannitol-salt-egg yolk (MSEY) agar and mannitol salt (MS) agar in detecting Staphylococcus aureus FRI-100 heated at 52 degrees C for 20 min in 100 mmol/L potassium phosphate buffer was determined. Brain heart infusion agar with 1% pyruvate (BHIP agar) supported the highest recovery of injured cells and was used as the control medium. Of the three selective media, significantly higher recovery of heat-injured cells was observed on BP agar than MSEY agar, and the poorest recovery was observed on MS agar (p < 0.05). Low recovery of unheated cells was obtained for MS compared with other media (p < 0.05). A reduction in populations occurred gradually in reagent-grade water stored for 14 days at -20 degrees C. There was no significant difference between BHIP agar and MS agar in the number of freeze-injured cells recovered from 1 to 14 days.     

A novel ferromagnetic thermo-stent for plaque stabilization that self-regulates the temperature

The purpose of this study is to investigate the vascular wall with a thermally self-regulating, cylindrical stent made of a low Curie temperature ferromagnetic alloy. Physiologic saline was circulated in the silicone model vessel implanted with the stent. The stent-temperature remained nearly constant for variable saline flows, saline temperatures, and magnetic flux densities. Stent implants of this type in human blood vessels could potentially enable thermotherapy and temperature determination without catheterization.     

Study of a Helium Film in 10 μm Porous Glass by Torsional Oscillator in Free Decay Mode

Dissipation and superfluid density of a thin helium film (superfluid transition at temperature T_c=0.88 K), placed in 10 m porous glass are studied as a function of oscillation amplitude or AC amplitude at fixed temperatures near superfluid transition. The measurements are performed using a high-Q torsional oscillator in the free decay mode as well as constant drive mode. Results show decreasing superfluid density with increasing velocity and non-monotonic behavior of the dissipation in the film.     

Analytical tool development for coarse break-up of a molten jet in a deep water pool

A computer code JASMINE-pre was developed for the prediction of premixing conditions of fuel–coolant interactions and debris bed formation behavior relevant to severe accidents of light water reactors. In JASMINE-pre code, a melt model which consists of three components of sub-models for melt jet, melt particles and melt pool, is coupled with a two-phase flow model derived from ACE-3D code developed at JAERI. The melt jet and melt pool models are one-dimensional representations of a molten core stream falling into a water pool and a continuous melt body agglomerated on the bottom, respectively. The melt particles generated by the melt jet break-up are modeled based on a Lagrangian grouped particle concept. Additionally, a simplified model pmjet was developed which considers only steady state break-up of the melt jet, cooling and settlement of particles in a stationary water pool. The FARO corium quenching experiments with a saturation temperature water pool and a subcooled water pool were simulated with JASMINE-pre and pmjet. JASMINE-pre reproduced the pressurization and fragmentation behavior observed in the experiments with a reasonable accuracy. Also, the influences of model parameters on the pressurization and fragmentation were examined. The calculation results showed a quasi-steady state phase of melt jet break-up during which the amount of molten mass contained in the premixture was kept almost constant, and the steady state molten premixed masses evaluated by JASMINE-pre and pmjet agreed well.     

Numerical prediction of fraction of eutectic phase in Sn−Ag−Cu soldring using the phase-field method

A combination of macroscale solidification simulation and phase-field calculation is employed to predict the volume fraction of the eutectic phase in Sn-4.0 mass% Ag-XCu solder alloys (X=0.5–1.1 mass%). The solidification simulation incorporates the cooling rate in the phase-field simulation. We assume the residual liquid solidifies as eutectic phase when the driving force for the nucleation of Cu₆Sn₅ amounts to a critical value, which is determined based on the experimental data. Though the calculation results depend on the experimental data, the obtained fractions are about 40% for 0.5 mass% Cu and more than 90% for 1.1 mass% Cu alloy, which shows good agreement with the experimental data.